• Journal of the Korean Geotechnical Society
• /
• v.36 no.12
• /
• pp.69-76
• /
• 2020

Since the mechanically stabilized earth walls have a form of retaining wall compatible with a narrow section, the geogrid overlaps according to the separation distance between the walls. There is a problem that the overall behavior may occur in the state of being integrated with the stress change due to the interaction of the geogrid. Therefore, a careful approach is required at the design stage, but there are currently no design criteria or guidelines in Korea. This study investigated the optimal reinforcement length ratio according to the retaining wall width to height ratio (width to height ratio, Wb/H) for these back-to-back mechanically stabilized earth walls. Retaining wall width ratio is 1.1H, 1.4H, 1.7H, 2.0H for Case II of the FHWA design standard, and the height is 3.0 m, 5.0 m, 7.0 m, and 10.0 m, which are most commonly applied. Through numerical analysis, the appropriateness of the FHWA design standard and the optimal reinforcement length ratio according to the height of the retaining wall and the width of the retaining wall were proposed.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.139-149
• /
• 2019

For retaining wall designs, horizontal earth pressure induced by traffic loads over the walls is calculated based on equivalent uniform pressure height. The AASHTO LRFD design standards propose equivalent uniform pressure height of traffic loads; however, the equivalent uniform pressure height is calibrated using the US standard trucks. As the domestic standard trucks are different from the US standard trucks, in this study, new domestic equivalent uniform pressure height is proposed using the Boussinesq theory varying vehicle directions, Poisson's ratios of pavement layers, and retaining wall height. The proposed equivalent uniform pressure heights are generally higher than those proposed by the AASHTO design standards because the axle loads and their densities of two domestic standard trucks are higher than those of the US standard trucks. The most highest equivalent uniform pressure height was found for traffic direction perpendicular to longitudinal direction of retaining wall.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.5
• /
• pp.153-162
• /
• 2007

For the reinforced earth wall constructed on a soft ground in parallel with replacing soft soils, the behavior of the wall according to variations of thickness and stiffness of soft layer, replacement depth, and wall height is investigated using a finite element method, in which incremental construction steps including consolidation of soft soil layer are considered. The behavior of wall is characterized by investigating displacements and settlements developing at the wall, and shear strains developing in a soil deposit. The stability of wall is, then, evaluated by comparing these values with the safety criteria determined on the basis of the literature. Based on the investigation, it is shown that the behavior of wall is influenced naturally from soft soil thickness(t), replacement depth(d) and wall height(h), but more significantly from d and h. In addition, it is also shown that the normalized replacement depth, d/h, required for the safety of wall is not influenced significantly by the variations of t and h. Consequently, it can be concluded that the proper replacement depth can be suggested in an equivalent value in terms of d/h, even for the cases where the wall height is varying with stations, but the variation is not significant.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6B
• /
• pp.627-634
• /
• 2008

In a numerical simulation of open channel turbulent flows using RANS (Reynolds averaged Navier-Stokes) equations model equipped with VOF (Volume of Fluid) scheme, the determination of wall roughness for wall function was studied. The roughness constant, based on the law-of-the-wall for flow on rough walls, obtained by experimental works for pipe flows is employed in general wall functions. However, this constant of wall function is the function of Froude number in open channel flows. Thus, the wall roughness should be determined by taking into account the effect of Froude number. In addition, the wall roughness should be corresponding to Manning's roughness coefficient widely used for open channels. In this study, the relation between wall roughness height as an input condition and Manning's roughness coefficient was investigated, and an equation for effective wall roughness height considering the characteristics of numerical models was proposed as a function of Manning's roughness coefficient.

• Advances in Computational Design
• /
• v.1 no.3
• /
• pp.221-234
• /
• 2016

The present study dictates the behavior of shear wall under a seismic event in slender high rise buildings, and studies the effect of height, location and distribution of shear wall in slender high rise building with and without boundary elements induced by the effect of an earthquake. Shear walls are located at the sides of the building, to counter the earthquake forces. This study is carried out in a 12 storeys building using SAP2000 software. The obtained results disclose that the behavior of the structure is definitely affected by the height and location of shear walls in slender high rise building. The stresses are concentrated at the limit between the shear wall region and the upper non shear wall especially for shear walls without columns. Displacements are doubled between the shear wall region and the upper non shear wall especially for shear walls without columns.

• Journal of the Korean Society of Safety
• /
• v.38 no.2
• /
• pp.44-51
• /
• 2023

With the recent increase in gas energy use, risk management for explosion accidents has been emphasized. Protective walls can be used to reduce damage from explosions. The KOSHA GUIDE D-65-2018 suggests the minimum thickness and height of protective walls, minimum reinforcement diameter, and maximum spacing of reinforcements for the structural safety of the protective walls. However, no related evidence has been presented. In this study, the blast load carrying capacity of the protective wall was analyzed by the pressure-impulse diagrams while changing the yield strength of the reinforcement, concrete compressive strength, reinforcement ratio, protective wall height, and thickness, to check the adequacy of the KOSHA GUIDE. Results show that failure may occur even with design based on the criteria presented by KOSHA GUIDE. In order to achieve structural safety of protective walls, additional criteria for minimum reinforcement yield strength and maximum height of protective wall are suggested for inclusion in KOSHA GUIDE. Moreover, the existing value for minimum reinforcement ratio and the thickness of the protective wall should be increased.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.4
• /
• pp.230-234
• /
• 2010

This study examined the effect of wall friction on deformation characteristics of the cellular bulkhead, in terms of artificial wall friction based on the results of model tests according to the existing penetration ratio and loading height. 1. The effect of wall friction on deformation characteristics of the cellular bulkhead turned out to be less as the loading height decreases and the penetration ratio increases. The yield load also becomes less as wall friction decreases. 2. The ratio of the rotational displacement to the horizontal displacement of the cellular bulkhead becomes less as the loading height decreases and the penetration ratio increases. Hence it is concluded that the effect of wall friction has close relationship with the rotational displacement.

• Journal of Korean Society of Forest Science
• /
• v.84 no.4
• /
• pp.409-414
• /
• 1995

This study was carried out for the analysis and comparison about the noise diminution effects by the height, width and density of Euonymus japonica wall, the distance of sound source, the distance of sound receiver, the height of sound source, and the height of sound receiver. The results obtained were summarized as follows; 1. After the establishment of tree wall, the volume of noise diminution measured 6.8dB and the effects of noise diminution measured heigher than before by 10.6% and t-value was significant at the 1% level 2. In simple correlation between the effects of noise diminution and variables, the density of tree wall was found as the most significant factor, and the last were found in the order of the distance of sound receiver, the width of tree wall, and the distance of sound source. 3. In partial correlation coefficients the effects of noise diminution and variables, the density of tree wall (r=-0.959) was found as the most significant factor, and the last were found in order of the distance of sound receiver (r=-0.906) and the width of tree wall (r=-0.753). 4. The estimated equation to measure the effects of noise diminution according to variables (the height of tree wall, the width of tree wall, the density of tree wall, the distance of sound source, the distance of sound receiver, the height of sound source, and the height of sound receiver) was $Y=69.520-1.672X_1-1.656X_2-0.066X_3-0.248X_4-3.134X_5-0.222X_6-0.343X_7$, and the coefficient of determination of this estimated equation was highly found as 0.950. 5. In semi-partial correlation coefficient the effects of noise diminution were found in the order of the density of tree wall, the distance of sound receiver, the width of tree wall, and the height of tree wall from the highest to the lowest. Therefore, it was considered that the density of tree wall, the distance of sound receiver, the width of tree wall and the distance of sound source should be controlled effectively to increase the effects of noise diminution by Euonymus japonica wall.

• Steel and Composite Structures
• /
• v.38 no.6
• /
• pp.671-690
• /
• 2021

Seismic responses of RC core wall with two outriggers are investigated in this study. In the models analyzed here, one of the outriggers is fixed at the top of the building and the second is placed at different levels along the height of the system. Each of the systems resulting from the placement of the outrigger at different locations is designed according to the prescriptive codes. The location of the outrigger changes along the height. Linear design of all the structures is accomplished by using prescriptive codes. Buckling restrained braces (BRBs) are used in the outriggers and forward directivity near fault and far fault earthquake record sets are used at maximum considered earthquake (MCE) level. Results from nonlinear time history analysis demonstrate that BRB outriggers can change the seismic responses like force distribution and deformation demand of the RC core-walls over the height and lead to the new plastic hinge arrangement over the core-wall height. Plasticity extension in the RC core wall occurs at the base as well as adjacent to the outrigger levels. Considering the maximum inter-story drift ratio (IDR) demand as an engineering parameter, the best location for the second outrigger is at 0.75H, in which the maximum IDR at the region upper the second outrigger level is approximately equal to the corresponding value in the lower region.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.5B
• /
• pp.301-312
• /
• 2012

This study investigates the wave height distributions in front of a perforated wall generated by obliquely incident monochromatic waves through laboratory experiments conducted in a wave basin. Attention is paid to the difference or similarity between a plain wall and a perforated wall. And the investigation is focused on the chamber width and side wall effects of a perforated wall on the propagation characteristics of waves. The main results of this study show that the normalized wave height along a perforated wall is a significant difference compare to a plain wall cases. The side wall in the chamber suppresses the growth of the stem waves.