Steel and Composite Structures

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Optimum location of second outrigger in RC core walls subjected to NF earthquakes

  • Beiraghi, Hamid (Department of Civil Engineering, Mahdishahr Branch, Islamic Azad University) ;
  • Hedayati, Mansooreh (Department of Civil Engineering, Mahdishahr Branch, Islamic Azad University)
  • Received : 2020.05.19
  • Accepted : 2021.02.18
  • Published : 2021.03.25
⟨ Previous Next ⟩

Abstract

Seismic responses of RC core wall with two outriggers are investigated in this study. In the models analyzed here, one of the outriggers is fixed at the top of the building and the second is placed at different levels along the height of the system. Each of the systems resulting from the placement of the outrigger at different locations is designed according to the prescriptive codes. The location of the outrigger changes along the height. Linear design of all the structures is accomplished by using prescriptive codes. Buckling restrained braces (BRBs) are used in the outriggers and forward directivity near fault and far fault earthquake record sets are used at maximum considered earthquake (MCE) level. Results from nonlinear time history analysis demonstrate that BRB outriggers can change the seismic responses like force distribution and deformation demand of the RC core-walls over the height and lead to the new plastic hinge arrangement over the core-wall height. Plasticity extension in the RC core wall occurs at the base as well as adjacent to the outrigger levels. Considering the maximum inter-story drift ratio (IDR) demand as an engineering parameter, the best location for the second outrigger is at 0.75H, in which the maximum IDR at the region upper the second outrigger level is approximately equal to the corresponding value in the lower region.

Keywords

References

  1. Abdollahzadeh, G. and Banihashemi, M. (2013), "Response modification factor of dual moment-resistant frame with buckling restrained brace (BRB)", Steel Compos. Struct., 14(6), 621-636. https://doi.org/10.12989/scs.2013.14.6.621.
  2. Abdollahzadeh, G. and Banihashemi, M. (2013), "Response modification factor of dual moment-resistant frame with buckling restrained brace (BRB)", Steel Compos. Struct., 14(6), 621-636. https://doi.org/10.12989/scs.2013.14.6.621.
  3. ACI 318-11 (2011), Building code requirements for structural concrete and commentary, ACI Committee 318, Farmington Hills.
  4. Aiken, I.D., Mahin, S.A. and Uriz, P. (2002), "Large-scale testing of buckling-restrained braced frames" Proceedings of the Japan Passive Control Symposium, Tokyo Institute of Technology, Japan.
  5. AISC (2010), Seismic provision for structural steel buildings, American Institute of Steel Construction: Chicago.
  6. Akkar, S., Yazgan, U. and Gulkan, P. (2005), "Drift estimates in frame buildings subjected to near-fault ground motions", J. Struct. Eng., 131(7), 1014-1024. https://doi.org/10.1061/(asce)0733-9445(2005)131:7(1014)
  7. Alam, Z., Sun, L., Zhang, C., Su, Z. and Samali, B. (2020a), "Experimental and numerical investigation on the complex behaviour of the localised seismic response in a multi-storey plan-asymmetric structure", Struct. Infrastruct. Eng., DOI 10.1080/15732479.2020.1730914.
  8. Alam, Z., Zhang, C. and Samali, B. (2020b), "Influence of seismic incident angle on response uncertainty and structural performance of tall asymmetric structure", Struct. Des. Tall Spec. Build., DOI 10.1002/tal.1750.
  9. Alavi, B. and Krawinkler, H. (2004), "Behavior of moment-resisting frame structures subjected to near-fault ground motions", Earthq. Eng. Struct. D., 33, 687-706. https://doi.org/10.1002/eqe.369.
  10. Applied Technology Council. (2010), ATC-72: Modeling and Acceptance Criteria for Seismic Design and Analysis of Tall Buildings, ATC: Redwood City, CA.
  11. ASCE/SEI 41-13. (2013), Seismic rehabilitation of existing buildings (Including Supplement # 1), American Society of Civil Engineers: Reston, VA.
  12. ASCE/SEI 7 (2010), Minimum design loads for buildings and other structures, American Society of Civil Engineers. Reston, VA.
  13. Asgarian, B. and Shokrgozar, H.R. (2009), "BRBF response modification factor", J. Constr. Steel Res., 65, 290-298. https://doi.org/10.1016/j.jcsr.2008.08.002.
  14. Baker, J.W. (2007), "Quantitative classification of near-fault ground motions using wavelet analysis", Bull. Seismol. Soc. Am., 97(5). 1486-1501. https://doi.org/10.1785/0120060255.
  15. Beiraghi, H. (2017), "Earthquake effects on the energy demand of tall reinforced concrete walls with buckling-restrained brace outriggers", Struct. Eng. Mech., 63(4), 521-536. https://doi.org/10.12989/sem.2017.63.4.521.
  16. Beiraghi, H. (2018a), "Reinforced concrete core-walls connected by a bridge with buckling restrained braces subjected to seismic loads", Earthq. Struct., 15(2), 203-214. https://doi.org/10.12989/eas.2018.15.2.203.
  17. Beiraghi, H. (2018b), "Near-fault ground motion effects on the responses of tall reinforced concrete walls with buckling-restrained brace outriggers", Scientia Iranica A, 25(4), 1987-1999. DOI:10.24200/sci.2017.4205.
  18. Beiraghi, H. (2018c), "Energy Dissipation of Reinforced Concrete Wall Combined with Buckling-Restrained Braces Subjected to Near- and Far-Fault Earthquakes", Iran J. Sci. Technol. T. Civ. Eng., 42(4), 345-359. https://doi.org/10.1007/s40996-018-0109-0.
  19. Beiraghi, H. (2018d), "Energy demands in reinforced concrete wall piers coupled by buckling restrained braces subjected to near-fault earthquake", Steel Compos. Struct., 27(6), 703-716. https://doi.org/10.12989/scs.2018.27.6.703.
  20. Beiraghi, H. (2019), "Earthquake effect on the concrete walls with shape memory alloy reinforcement", Smart Struct. Syst., 24(4), 491-506. https://doi.org/10.12989/sss.2019.24.4.491.
  21. Beiraghi, H. (2019a), "Fragility assessment of shear walls coupled with buckling restrained braces subjected to near-field earthquakes", Steel Compos. Struct., 33(3), 389-402. https://doi.org/10.12989/scs.2019.33.3.389.
  22. Beiraghi, H. (2019b), "Seismic response of dual structures comprised by Buckling-Restrained Braces (BRB) and RC walls", Struct. Eng. Mech., 72(4), 443-454. https://doi.org/10.12989/sem.2019.72.4.443.
  23. Beiraghi, H. and Siahpolo, N. (2016), "Seismic assessment of RC core-wall building capable of three plastic hinges with outrigger", Struct. Des. Tall Spec. Build., 26(2), e1306. https://doi.org/10.1002/tal.1306.
  24. Bengar, H.A. and Aski, R.M. (2016), "Performance based evaluation of RC coupled shear wall system with steel coupling beam", Steel Compos. Struct., 20(2), 337-355. https://doi.org/10.12989/scs.2016.20.2.337.
  25. Bernal, D. (1994), "Viscous damping in inelastic structural response", J. Struct. Eng., 120(4), 1240-1254. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:4(1240).
  26. Bertero, V., Mahin, S. and Herrera, R. (1978), "A seismic design implications of near-fault San Fernando earthquake records", Earthq. Eng. Struct. D., 6(1), 31-42. https://doi.org/10.1002/eqe.4290060105.
  27. Black, C., Makris, N. and Aiken, I. (2002), "Component testing, stability analysis and characterization of buckling-restrained braces", Report No. PEER-2002/08, Pacific Earthquake Engineering Research Center, University of California, Berkeley, CA, USA.
  28. Bosco, M. and Marino, E.M. (2013), "Design method and behavior factor for steel frames with buckling restrained braces", Earthq. Eng. Struct. D., 42(1), 1243-1263. DOI:10.1002/eqe.2269. DOI:10.1002/eqe.2269.
  29. Calugaru, V. and Panagiotou, M. (2012), "Response of tall cantilever wall buildings to strong pulse type seismic excitation", Earthq. Eng. Struct. D., 41, 1301-1318. DOI:10.1002/eqe.1185.
  30. CEN EC8. (2004), "Design of Structures for Earthquake Resistance. European Committee for Standardisation: Brussels", Belgium", J. Struct. Eng., 136(11), 1435-1443.
  31. Chen, Y., Cai, K. and Wang, X, (2018), "Parameter study of framed-tube structures with outriggers using genetic algorithm", Struct. Des. Tall Spec. Build., 27(14), 1-26, https://doi.org/10.1002/tal.1499.
  32. Chen, Y., McFarland, D.M., Wang, Z., Spencer, B.F. and Bergman, L.A. (2010), "Analysis of Tall Buildings with Damped Outriggers", J. Struct. Eng., 136(11), 1435-1443. DOI: 10.1061/(ASCE)ST.1943-541X.0000247.
  33. Choi, H., Ho, G., Joseph, L. and Mathias, N. (2017), "Outrigger Design for High-Rise Buildings", 2nd Ed.: An output of the CTBUH Outrigger Working, Eng. Struct. D., 41, 1301-1318.
  34. Chopra, A.K. (2001), Dynamics of structures. Prentice-Hall: New Jersey.
  35. CSA Standard A23.3-04. (2005), Design of Concrete Structures. Canadian Standard Association: Rexdale, Canada.
  36. Eskandari, R. and Vafaei, D. (2015), "Effects of near-fault records characteristics on seismic performance of eccentrically braced frames", Struct. Eng. Mech., 56(5), 855-870. https://doi.org/10.12989/sem.2015.56.5.855.
  37. Eskandari, R., Vafaei, D., Vafaei, J. and Shemshadian, M.E. (2017), "Nonlinear static and dynamic behavior of reinforced concrete steel-braced frames", Earthq. Struct., 12(2), 191-200. https://doi.org/10.12989/eas.2017.12.2.191.
  38. ETABS, Version 13.1.1. (2013), Computers and Structures. Inc.: Berkeley, California, USA.
  39. Fahnestock, L.A., Ricles, J.M. and Sause, R. (2007a), "Experimental evaluation of a large-scale buckling-restrained braced frame", J. Struct. Eng., 133(9), 1205-1214. https://doi.org/10.1061/(ASCE)0733-9445(2007)133:9(1205).
  40. FEMA P695 (2009), Quantification of Building Seismic Performance Factors (ATC-63 Project), Federal Emergency Management Agency, Washington D.C.
  41. Gao, D., You, P., Zhang, L. and Yan, H. (2018), "Seismic behavior of SFRC shear wall with CFST columns", Steel Compos. Struct., 28(5), 527-539. https://doi.org/10.12989/scs.2018.28.5.527.
  42. Ghodsi, T., Ruiz, J.F., Massie, C. and Chen, Y. (2010), "Pacific earthquake engineering research/seismic safety commission tall building design case study", Struct. Des. Tall Spec. Build., 19(2), 197-256. https://doi.org/10.1002/tal.542.
  43. Ghorbanirenani, I., Tremblay, R., Leger, P. and Leclerc, M. (2012), "Shake table testing of slender rc shear walls subjected to eastern north america seismic ground motions", J. Struct. Eng., 138(12), 1515-1529. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000581.
  44. Grant, D. and Diaferia, R. (2012), "Assessing adequacy of spectrum matched ground motions for response history analysis", Earthq. Eng. Struct. D., 42(9), 1265-1280 DOI: 10.1002/eqe.2270.
  45. Guneyisi, E.M. and Ameen, N. (2014), "Structural behavior of conventional and buckling restrained braced frames subjected to near-field ground motions", Earthq. Struct., 7(4), 553-570. https://doi.org/10.12989/eas.2014.7.4.553.
  46. Inoue, K., Sawaisumi, S. and Higashibata, Y. (2001), "Stiffening requirements for unbonded braces encased in concrete panels", ASCE J. Struct. Eng., 127(6), 712-719. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:6(712).
  47. Jones, P. and Zareian, F. (2013), "Seismic response of a 40-storey buckling-restrained braced frame designed for the Los Angeles region", Struct. Des. Tall Spec. Build., 22(3), 291-299. DOI:10.1002/tal.687.
  48. Kim, H.S. (2017), "Optimum design of outriggers in a tall building by alternating nonlinear programming", Eng. Struct., 150, 91-97. https://doi.org/10.1016/j.engstruct.2017.07.043.
  49. Kim, J., Park, J. and Kim, S. (2009), "Seismic behavior factors of buckling restrained braced frames", Struct. Eng. Mech., 33(3), 261-284. https://doi.org/10.12989/sem.2009.33.3.261.
  50. Klemencic, R., Fry, A., Hooper, J.D. and Morgen, B.G. (2007), "Performance based design of ductile concrete core wall buildings-issues to consider before detail analysis", Struct. Des. Tall Spec. Build., 16, 599-614. https://doi.org/10.1002/tal.437.
  51. LATBSDC (2011), An Alternative Procedure For Seismic Analysis and Design of Tall Buildings Located in the Los Angeles Region, Los Angeles Tall Buildings Structural Design Council: Los Angeles.
  52. Leger, P. and Dussault, S. (1992), "Seismic-energy dissipation in MDOF structures", J. Struct. Eng., 118(5), 1251-1269. https://doi.org/10.1061/(ASCE)0733-9445(1992)118:5(1251).
  53. Li, J., Zhou, H. and Ding, Y. (2018), "Stochastic seismic collapse and reliability assessment of high-rise reinforced concrete structures", Struct. Des. Tall Spec. Build., 27(2), e1417. https://doi.org/10.1002/tal.1417.
  54. Mahmoudi, M. and Zaree, M. (2010), "Evaluating response modification factors of concentrically braced steel frames", J. Constr.l Steel Res., 66(10), 1196-1204. https://doi.org/10.1016/j.jcsr.2010.04.004.
  55. Mander, J.B., Priestley, M.J.N. and Park, R. (1988), "Theoretical stress-strain model for confined concrete", ASCE J. Struct. Eng., 114(8), 1804-1826. https://doi.org/10.1061/(ASCE)0733-9445(1988)114:8(1804).
  56. National Institute of Standards and Technology, (2012), Seismic Design of Cast-in-Place Concrete Special Structural Walls and Coupling Beams, NEHRP Seismic Design Technical Brief No. 6 2012.
  57. Nguyen, A.H., Chintanapakdee, C. and Hayashikawa, T. (2010), "Assessment of current nonlinear static procedures for seismic evaluation of BRBF buildings", J. Constr. Steel Res., 66(8-9), 1118-1127. DOI:10.1016/j.jcsr.2010.03.001.
  58. NZS 3101. (2006), New Zealand Standard, Part 1- The Design of Concrete Structures. Standards New Zealand: Wellington, New Zealand.
  59. Orakcal, K. and Wallace, J.W. (2006), "Flexural modeling of reinforced concrete walls-experimental verification", ACI Struct. J., 103(2), 196-206.
  60. Panagiotou, M. and Restrepo, J. (2009), "Dual-plastic hinge design concept for reducing higher-mode effects on high-rise cantilever wall buildings", Earthq. Eng. Struct. D., 38(12), 1359-1380. https://doi.org/10.1002/eqe.905.
  61. Park, R. and Paulay, T. (1975), Reinforced concrete structures. Wiley: New York, United States of America.
  62. Paulay, T. and Priestley, M.J.N. (1992), Seismic Design of Reinforced Concrete and Masonry, Wiley: New York, United States of America.
  63. PERFORM-3D. (2006), Nonlinear Analysis and Performance Assessment for 3D Structures. V.4, User Guide. Computers and Structures, Inc.: Berkeley, CA.
  64. PERFORM-3D. (2011), Nonlinear Analysis and Performance Assessment for 3D Structures, V.4.0.3. Computers and Structures, Inc.: Berkeley, CA.
  65. Priestley, M.J.N., Calvi, G.M. and Kowalsky, M.J. (2007), Displacement-Based Seismic Design of Structures. IUSS Press: Pavia, Italy.ISBN:88-6198-000-6.
  66. Qin, Y., Shu, G., Zhou, X., Han, J. and He, Y. (2019), "Heightthickness ratio on axial behavior of composite wall with truss connector", Steel Compos. Struct., 30(4), 315-325. https://doi.org/10.12989/scs.2019.30.4.315.
  67. Rahgozar, R. and Sharifi, Y. (2009), "An approximate analysis of framed tube, shear core and belt truss in high-rise building", Struct. Des. Tall Spec. Build., 18, 607-624. DOI:10.1002/tal.503.
  68. Sahoo, D.R. and Chao, S. (2010), "Performance-based plastic design method for buckling-restrained braced frames", Eng. Struct., 32(1), 2950-2958. DOI: 10.1016/j.engstruct.2010.05.014.
  69. Satake, N., Suda, K., Arakawa, T., Sasaki, A. and Tamura, Y. (2003), "Damping evaluation using full-scale data of buildings in Japan", J. Struct. Eng., 129(4), 470-477. DOI: 10.1061/(ASCE)0733-9445(2003)129:4(470)
  70. Simpson, Gumpertz, Heger, Inc. (2009), "Detailed Design Writeup for BRBF building", Simpson, Gumpertz, & Heger, Inc.: San Francisco, CA.
  71. Smith, B.S. and Coull, A. (1991), Tall building Structures: Analysis and Design, 1 edn. John Wiley & Sons Inc.: New York.
  72. Smith, B.S. and Salim, I. (1981), "Parameter study of outrigger-braced tall building structures", J. Struct. Div., 107(10), 2001-2014. https://doi.org/10.1061/JSDEAG.0005798.
  73. Smith, R.J. and Willford, M.R. (2007), "The damped outrigger concept for tall buildings", Struct. Des. Tall Spec. Build., 16(4), 501-517. DOI:10.1002/tal.413
  74. Soong, T.T. and Spencer, B.F. (2002), "Supplemental energy dissipation: state-of-the-art and state-of-the-practice", Eng. Struct., 24(3), 243-259. DOI: 10.1016/S0141-0296(01)00092-X.
  75. Taranath, B.S. (1974), "Optimum belt truss location for high rise structures", Eng. J., 18-21.
  76. Taranath, B.S. (1988), Structural Analysis and Design of Tall Buildings, Mc Graw Hill: New York.
  77. Teran-Gilmore, A. and Ruiz-Garcia, J. (2011), "Comparative seismic performance of steel frames retrofitted with buckling-restrained braces through the application of Force-Based and Displacement-Based approaches", Soil Dynam. Earthq. Eng., 31, 478-490. https://doi.org/10.1016/j.soildyn.2010.11.003.
  78. Thomsen, J.H. and Wallace, J.W. (2004), "Experimental verification of displacement-based design procedures for slender reinforced concrete structural walls", J. Struct. Eng.-ASCE, 130(4), 618-630. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:4(618)
  79. Tremblay, R., Bolduc, P., Neville, R. and DeVall, R. (2006), "Seismic testing and performance of buckling restrained bracing systems", Can. J. Civil Eng., 33, 183-198. https://doi.org/10.1139/l05-103.
  80. Tremblay, R., Degrange G. and Blouin J. (1999), "Seismic rehabilitation of a four-storey building with a stiffened bracing system", Proceedings of the 8th Canadian Conference on Earthquake Engineering, Vancouver, Canada.
  81. Tsai, K.C., Hsiao, P.C., Wang, K.J., Weng, Y.T., Lin, M.L., Lin, K.C., Chen, C.H., Lai, J.W. and Lin, S.L. (2008), "Pseudo-dynamic tests of a full-scale CFT/BRB frame-Part I: Specimen design, experiment and analysis", Earthq. Eng. Struct. D., 37, 1081-1098. https://doi.org/10.1002/eqe.804.
  82. Ucar, T, (2020), "Computing input energy response of MDOF systems to actual ground motions based on modal contributions", Earthq. Struct., 18(2), 263-273. https://doi.org/10.12989/eas.2020.18.2.263.
  83. Uriz, P. and Mahin, S.A. (2008), "Toward earthquake-resistant design of concentrically braced steel-frame structures", PEER 2008/08, Pacific Earthquake Engineering Research Center, University of California, Berkeley, CA.
  84. Vafaei, D. and Eskandari, R. (2015), "Seismic response of mega buckling-restrained braces subjected to fling step and forward directivity near-fault ground motions", Struct. Des. Tall Spec. Build., 24(9), 672-686. DOI: 10.1002/tal.1205.
  85. Vafaei, D. and Eskandari, R. (2016), "Seismic performance of steel mega braced frames equipped with shape memory alloy braces under near fault earthquakes", Struct. Des. Tall Spec. Build., 25(1), 3-21. DOI: 10.1002/tal.1225.
  86. Vafaei, D., Shemshadian, M.E. and Zahrai, S.M. (2010), "Seismic behavior of BRB frames under near fault excitations", Proceedings of the 9th US National and 10th Canadian Conference on Earthquake Engineering.
  87. Watanabe, A. (1992), "Development of composite brace with a large ductility", Proceedings of the U.S.-Japan Workshop on Composite and Hybrid Structures, Berkeley, CA, September 10-12.
  88. Watanabe, A., Hitomi, Y., Saeki, E., Wada, A. and Fujimoto, M. (1988), "Properties of brace encased in buckling-restraining concrete and steel tube", Proceedings of the 9th World Conference on Earthquake Engineering, Tokyo-Kyoto, Japan.
  89. Wu, J.R. and Li, Q.S. (2003), "Structural performance of multi-outrigger-braced tall buildings", Struct. Des. Tall Spec. Build., 12(2), 155-176. DOI:10.1002/tal.219.
  90. Xu, P.F., Huang, J.F., Xiao, C.Z., Li, Y.G. and Huang, S.M. (1999), "Some problems in seismic design of frame-core wall structures with strengthened stories", J. Build. Struct., 20(4), 2-10.
  91. Zhang, C., Alam, Z. and Samali, B. (2016), "Evaluating contradictory relationship between floor rotation and torsional irregularity coefficient under varying orientations of ground motion", Earthq. Struct., 11(6), 1027-1041. https://doi.org/10.12989/eas.2016.11.6.1027.
  92. Zhang, C., Alam, Z., Sun, L., Su, Z. and Samali, B. (2018), "Fibre Bragg grating sensor-based damage response monitoring of an asymmetric reinforced concrete shear wall structure subjected to progressive seismic loads", Struct. Control Health Monit., DOI 10.1002/stc.2307.
  93. Zhao, X., Yaomin, D., and Tianyi, Y. (2014), "Outrigger System Optimization under Story Drift and Vibration PeriodConstraints for SuperTall Buildings", In IABSE Symposium Report, 102(37), 475-482. International Association for Bridge and Structural Engineering, 2014. https://doi.org/10.2749/222137814814028034
  94. Zhou, H. and Li, J. (2019), "Comparison study of two criteria for identification of structural dynamic stability", Science China Technol. Sci., 62(5), 856-867. https://doi.org/10.1007/s11431-017.
  95. Zhou, H., Li, J. and Ren, X., (2016), "Multiscale stochastic structural analysis toward reliability assessment for large complex reinforced concrete structures", Int. J. Multiscale Comput. Eng., 14(3), 303-321. https://doi.org/10.1061/(ASCE)EM.1943-7889.0001618.
  96. Zhou, Y. and Li, H. (2013), "Analysis of a high-rise steel structure with viscous damped outriggers", Struct. Des. Tall Spec. Build., 23(13), 963-979. https://doi.org/10.1002/tal.1098.
  97. Zhu, L., Zhang, C., Guan, X., Uy, B., Sun, L. and Wang, B. (2018), "The multi-axial strength performance of composite structural B-C-W members subjected to shear forces", Steel Compos. Struct., https://doi.org/10.12989/scs.2018.27.1.075.

Cited by

  1. Feasibility study of buckling-restrained braces with PM-35 steel core vol.79, pp.2, 2021, https://doi.org/10.12989/sem.2021.79.2.199