• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.441-444
• /
• 1998

This paper is concerned with researching latch-up immune CMOS structure was performed. By the simulation results, the connecting layer had more effect than the buried layer to latch-up immune. When the connecting layer was the dose 1*10$^{14}$ /cm$^{2}$ and the energy 500KeV, the trigger current was more 0.6mA/.mu.m and the trigger voltage was 6V. The more the connecting layer dose was lower, the more the latch-up immune characteristics was butter.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.15 no.3
• /
• pp.30-34
• /
• 1978

A bridge inverter circuit with a paralled resonant circuit load is analyzed. The approach to the circuit analysis leads to reasonable reality. The limit of trigger frequency, the range of SCR turn-off time, the peak capacitor voltage and the relation between the load current and trigger rate are derived for the suitable design criteria. Numerical method is used for calculation of transcendental equation.

• Journal of IKEEE
• /
• v.18 no.1
• /
• pp.25-30
• /
• 2014

In this paper, SCR(Silicon Controlled Rectifier)-based ESD(Electrostatic Discharge) protection circuit for power clamp is proposed. In order to improve latch-up immunity caused by low holding voltage of the conventional SCR, it is modified by inserting n+ floating region and n-well, and extending p+ cathode region in the p-well. The resulting ESD capability of our proposed ESD protection circuit reveals a high latch-up immunity due to the high holding voltage. It is verified that electrical characteristics of proposed ESD protection circuit by Synopsys TCAD simulation tool. According to the simulation results, the holding voltage is increased from 4.61 V to 8.75 V while trigger voltage is increased form 27.3 V to 32.71 V, respectively. Compared with the conventional SCR, the proposed ESD protection circuit has the high holding voltage with the same triggering voltage characteristic.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.4
• /
• pp.351-358
• /
• 2013

We propose a correction method of nonlinear frequency sweep in an FMCW(Frequency Modulated Continuous Wave) laser range finder. FMCW laser range finder requires linear frequency sweep for high resolution, and nonlinear frequency sweep makes the system performance degrade. In general, VCO(Voltage Controlled Oscillator) which is a component used for frequency modulation in FMCW method has nonlinear property. To correct the nonlinear frequency sweep, we utilize an auxiliary delay structure for generating trigger signal of ADC(Analog to Digital Converter). Because the trigger signal has same rate of change with the beat signal, the nonlinearity of the beat signal can be corrected. the experimental results show that the proposed method effectively eliminates the nonlinear frequency sweep problem and enhances the system performance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.144.1-144.1
• /
• 2015

The triggered vacuum switch(TVS) is a one of the important component in consisiting high power control systems(HPCS). The operating condition is depended on material, geometry, operating power and so on. Our research is focused on the effects of thses basic properties and ptimized condition, because these are critical conditons in understanding the TVS operation. Our experiment is accomplished with a copper electrode and a tungsten trigger pin after being assembled into a vacuum chamber. The operating voltage in our system is more than dozens of kV at the 5kV trigger pulse. Our goal is up to 300kJ, therefore the currents should be more optimized in additional experiments,

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1823-1826
• /
• 2002

The purpose of this experiment was to develope Triggered Vacuum Switch (TVS) for the high voltage and high current. The TVS has an array of rods of alternate polarity in which a fixed gap spacing is maintained between the rods. The cross section of each rod has trapezoidal shape. It consists of electrode, ceramic chamber, getter and trigger. Currently, triggered vacuum switch (TVS) with seal-off has been designed and fabricated at PAL. An experimentation and trigger devices for TVS were designed for testing characteristics of electricity. For making the prototype of TVS, it is developed of fabrication process and fined of electrode material. The fabrication of the TVS is a lot of process which have manufacturing of part, chemical clean, ceramic brazing and metal welding. The fabricated TVS is tested of leak for vacuum, hold-off voltage and conditioning of trigger system. The TVS has pinch-off after it is removed of gas in the TVS and activated of getter in degassing furnace. The prototype TVS tested about 20 kV, 75 kA, 83 ${\mu}s$ with 100 kJ capacitor bank and inductance 5 ${\mu}H$. This paper describes the results of tests and the characteristics of the switch.

• Journal of Sensor Science and Technology
• /
• v.6 no.3
• /
• pp.194-199
• /
• 1997

When voltage or current gets out of the magnetic sensor as it is, we have often faced the problems such as introduction of noise and loss of voltage. In order to reduce these problems, a 2 drain MAGFET operating in the saturation region and fabricated by CMOS process, the system of I/V converter, VCO with operational amplifier, and V/F conversion circuits with Schmitt Trigger are designed and fabricated in one package. The absolute sensitivity of magnetic sensor shows 1.9 V/T and the product sensitivity is $3.2{\times}10^{4}\;V/A{\cdot}T$. The characteristic of V/F conversion is very stabilized and has the value of 190 kHz/T.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.6
• /
• pp.29-37
• /
• 2012

As the demand for the fresh non-thermal food is increased, it is required to develop the fast and perfect sterilization method. The conventional sterilization method using ultraviolet lamp has some disadvantages such as imperfect sterilization and longer process time. In this research, IPL(Intense Pulsed Light) sterilization system is introduced to overcome the drawbacks of the conventional system, and suitable power supply architecture for the system is discussed. Since the IPL sterilization system uses Zenon lamps which requires the 600~2,100[V] for the lightning and 16~30[kV] for the trigger, the converter for the system should be able to generate the high voltage and to discharge the large amount of energy instantaneously. In this research a new power system architecture which has a modified forward converter topology with two switches for generating high voltage and a capacitor bank to control the energy for the lightning by switching is introduced.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.12
• /
• pp.584-590
• /
• 2002

Crowbar system is usually applied to a pulsed power system in which a capacitor bank is discharged into a load. This provides a free wheeling path for the load current and prevents the capacitor from recharging due to a reverse voltage. Usually diodes have been used as a crowbar switch, but it is not a practical system because the cost of the diodes goes up enormously with increasing the system voltage and current. This paper presents a novel protection scheme of a charging and discharging system of a 300 kJ capacitor bank using a low-cost crowbar system which consists of a crowbar switch and resistors. Triggered vacuum switch(TVS) was used for a crowbar switch, and Rogowski coil was used to determine a trigger time of TVS. When this crowbar system is applied to our pulsed power system which consists of capacitor bank($123muF$), inductor() for forming a pulse, load resistor$(100 m\Omega)$, and a closing switch, instantaneous reversal voltage of capacitor bank could be limited less than 1.8 ㎸ until capacitor bank was charred to 17 ㎸.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.3
• /
• pp.343-348
• /
• 2008

We investigated the quench characteristics accordance with increase of turns and applied voltage of matrix-type superconducting fault current limiter (SFCL) with $1{\times}3$ matrixes. The matrix-type SFCL consists of the trigger part to apply magnetic field and the current-limiting part to limit fault current. The fault current limiting characteristics according to the increase of magnetic field and applied voltage were nearly same. This is because the application of magnetic field has not an affect on total impedance of SFCL. When number of turns of reactor increased, the voltage difference between two superconducting units in the current-limiting part according was decreased. The resistance difference generated in two superconducting units also was decreased. Therefore, we confirmed that the differences of critical behaviors between superconducting units by application of magnetic field were decreased. By this results, we could be decided the optimum number of turns of reactor to apply magnetic field.