• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.117-125
• /
• 2014

The temperature distribution of steady state rolling tires with detailed tread blocks is numerically predicted using the three dimensional full patterned tire model. A three dimensional periodic patterned tire model is constructed by copying 1-sector mesh in the circumferential direction. Using the static tire contact analysis, the strain cycles during one revolution are approximated with the strains at Guassian points of the elements which are sector-wise repeated within the same circular ring of elements, by neglecting the tire rolling effect. Based upon the multi-axial fatigue theory, the maximum principal strain is used to represent the combined effect of six strain components on the hysteretic loss. In the following, the deformation due to the inflation and vertical load is calculated using ABAQUS. Then heat generation rate in each element is calculated using an in-house code. Lastly, temperature distribution is calculated using ABAQUS again. Through the numerical experiments, the validity of the proposed prediction method is examined by comparing with the experiment and the temperature distribution of a patterned tire model is compared with those of the main-grooved simple tire model.

• Elastomers and Composites
• /
• 제8권1호
• /
• pp.33-51
• /
• 1973

We have studied the blending effects of Diene NF 35 R and Alfin 1530 at various blending ratios, 100/0, 70/30, 50/50, 30/70, 0/100, and of carbon black HAF-HS and ISAF-HS at various compounding ratios of 45 PHR, 55 PHR, 65 PHR, for tyre tread rubber. As the results, it was found that; 1. For tyre tread rubber, as the blending ratio, AR 1530/Diene NF 35R, indicated 70/30, the physical properties we examined were most excellent. 2. Excellent result was obtained in the case of carbon black compounding ratio of 55 PHR. The compounding of ISAF-HS made better result than that of HAF-HS for tensile strength, but the compounding of HAF-HS made better result than that of ISAF-HS for tearing strength and best result for abrasion quantity. 3. Heat buildup obtained from compounding carbon black HAF-HS indicated low temperature than that from compounding carbon black HAP-HS. As the compounding amount of carbon black increased, and as the blending amount of AR 1530 decreased, the heat buildup increased. 4. Carbon black was more efficient to AR 1630 than io Diene NF 35 R. 5. In the physical properties, mooney viscosity and mooney scorch time, as the compounding amount of carbon black increased, the values of mooney viscosity increased, but that of mooney scorch time had a max. point at the compoundiug amount of carbon black, 55 PHR.

• 실천공학교육논문지
• /
• 제6권1호
• /
• pp.1-7
• /
• 2014

이 연구는 귀납법적 확증(confirmation)을 위해서 실행하는 실험이 확률론적 추론임을 밝히고 이의 단점을 보완하기 위해서 적용된 확률적 확인론에 따라서 수행하는 실험에서 통제하는 절차와 방법을 다루었다. 이 통제란 알려진 조건과 상황들을 인위적으로 조작하되 가설에서 명시된 특정조건(즉 독립변수) 이외의 조건(기타 변수)이 작용하여 현상이 발생(종속변수)될 가능성을 막는 것이다. 특정조건에 의하여 현상이 발생할 가능성을 극대화 시키고 기타 조건에 의하여 현상이 발생할 가능성을 최소화시키는 것이다. 그렇게 함으로써 특정 선행사건(독립변수)과 후행사건(종속변수) 사이의 진정한 인과관계성(the causal relationship)을 객관적으로 정확하게 추론하도록 보장하는 방법이 통제인 것이다. 이 연구에서는 변수통제에 대해 좀 더 구체적으로 다루기 위해 대표적인 헬스기구인 Elliptical Trainer (ET)와 Tread Mill (TM)를 이용한 실험에서 변수통제를 가하여 운동속도(독립변수)에 따른 에너지 소비량 변화(종속변수)와 운동속도(독립변수)에 따른 호흡교환율(RER)과 심장 박동율(HR)의 변화(종속변수)를 얻었다. 마지막으로 이 통제를 통해 얻어진 실험결과들을 그래프로 그려 그 결과에 따라 연구의 결론이 다루어졌다.

• Journal of Biosystems Engineering
• /
• 제12권4호
• /
• pp.9-15
• /
• 1987

The vibrational characteristics of a radial-ply (155SR13 4PR) and a biased-ply tire (6.15-134PR) were investigated for examining the effects of tires with different structure on the ride characteristics of the vehicle. The natural frequencies at the tread band, mode shapes, and damping factors of two tires at the state of plane vibration were determined experimentally. The test work was performed at four levels of the inflation pressure, ranging from 171.7 kPa to 245.2 kPa, and three levels of the vertical load, deviating by 10% from the standard load designated by the Department of Transportation of the United States of America. The following results were drawn by the analysis of the test results: 1. The first-order natural frequencies of the radial-ply and the biased-ply tires at the tread band were 112 Hz and 159 Hz, respectively, at the state o f the free vibration when the inflation pressure of 196.2 kPa was applied. It was known that the biased-ply tire has higher resonant frequency than the radial-ply tire and the natural frequencies of the both tires move to the high frequency range as t he inflation pressure is increased. 2. The vibration modes of both tires were quite different. No big difference in mode shapes was examined as the inflation pressure was increased. But the natural frequencies of two tires were changed. For the radial-ply tire, no difference in mode shape was found whether the vertical load was applied or not. But a significant difference in mode shape was examined for the biased-ply tire. 3. Any difference was not found in damping factor as the different inflation pressures were applied. 4. When no vertical load was applied, damping factors of the radial-ply and biased-ply tire at the state of the natural vibration ranged from 2.6 to 5.9%, and from 4.1 to 7.8%, respectively. It was estimated that the radial-ply tire would have better cushioning than the biased-ply tire since the vertical spring rate of the radial-ply tire was much less than that of the biased-ply tire, even though the damping effect of the radial-ply tire was smaller than that of the biased-ply tire.

• Elastomers and Composites
• /
• 제44권3호
• /
• pp.232-243
• /
• 2009

근래 고성능 친환경 타이어의 개발요구에 의하여 경제성(낮은 회전 저항)과 안전성(wet traction) 및 내마모성면에서 균형있는 특성을 가지는 타이어 트레드 고무의 합성 제조 기술이 중요하게 대두된다. 이를 위하여 다양한 기능성 용액중합 SBR의 개발과 함께 고무/충전제 간의 상호작용 증진 기술이 학술적으로나 산업적으로 활용되고 있다. 본 고에서는 기존의 카본블랙 고무와 함께 최근 green tire로서 각광 받는 실리카 충전 고무에서 충전제와 상호반응이 가능한 화학적 변성 SBR과 커플링제를 이용한 고성능 타이어 트레드 고무의 합성 제조 기술에 대하여 최근 연구 방향과 함께 작용 메카니즘에 대하여 고찰하였다.

• Elastomers and Composites
• /
• 제56권4호
• /
• pp.234-242
• /
• 2021

The demand for truck bus radial (TBR) tires with enhanced fuel efficiency and wear resistance have grown in recent years. In addition, as the issue of particulate matter and air pollution increases, efforts are being made to reduce the generation of particulate matter. In this study, the properties of epoxidized natural rubber (ENR) containing a silica-friendly functional group were evaluated by considering it as a base rubber and varying the silica ratio in this binary filler system. The results showed that the wear resistance of the NR/BR blend compound decreased as the silica ratio increased. In contrast, the ENR/BR blend compound exhibited an increase in wear resistance as the silica ratio was increased. In particular, the ENR-50/BR blend compound showed the best wear resistance due to the presence of several epoxide groups. Furthermore, we observed that for tan 𝛿 at 60℃, higher epoxide content resulted in the higher T_g of the rubber, indicating a higher tan 𝛿 at 60℃. On the other hand, it was confirmed that increasing the silica ratio decreased the value of tan 𝛿 at 60℃ in all compounds. In addition, we measured the amount of wear particulate matters generated from the compound wear. These measurements confirmed that in the binary filler system, regardless of the filler type, the quantity of the generated wear particulate matters as the filler-rubber interaction increased. In conclusion, the silica filled ENR/BR blend compound exhibited the lowest generation of wear particulate matters.

• Composites Research
• /
• 제36권3호
• /
• pp.141-153
• /
• 2023

본 리뷰 논문에서는 일반 접촉 역학 이론과 더불어 유기탄성체 마찰에 관한 이론 및 배경을 소개한다. 특히 Greenwood & Williamson 접촉 역학 이론을 확장하여 거친 표면을 자기-아핀(self-affine) 특성으로 고려한 접촉 역학 및 마찰의 수학적 모델을 제시한 Klüppel & Heinrich 이론을 중심으로 유기탄성체 복합재료의 마찰 거동에 대해 살펴본다. 자기-아핀 특성에 의한 노면의 멀티스케일 거칠기로 인해 미끄러짐 마찰 시 유기탄성체 복합재료는 다양한 주파수에 따른 동적 변형이 가해지며 이때 재료가 나타내는 점탄성이 마찰 거동에 주요한 영향을 미친다. 따라서 유기탄성체 복합재료의 비선형 점탄성을 고려하여 광범위한 주파수 영역에서의 점탄성 거동인 마스터커브를 구축하는 원리 및 방법을 제시하였다. 마지막으로 유기탄성체 복합재료 마찰 이론을 타이어 트레드 컴파운드와 노면 간의 마찰에 응용한 실험적 결과와 그 물리적 의미를 이론과 접목하여 설명하였다.

• 대한토목학회논문집
• /
• 제26권3D호
• /
• pp.461-467
• /
• 2006

노면에 차량 검지센서를 설치하여 개별차량의 속도자료를 수집하는 경우, 일반적으로 일정거리가 이격되게 설치한 두 개 이상의 차량 검지센서간의 반응시간을 활용하여 차량의 속도를 산출하게 된다. 본 논문에서는 차로당 센서 1개만을 설치하여 개별차량의 속도 산출을 함에 있어, 기존 방법인 파형의 기울기를 이용하여 속도 추정하는 방법(Case 1)과 평균차량길이를 적용한 속도산출(Case2), 새로 고안한 방법인 단일 테이프스위치(Tape Switch) 센서를 수평형으로 설치하고 평균축거를 적용하여 속도 추정하는 방법(Case 3), 그리고 테이프스위치 센서를 사선형으로 설치하고 차량의 평균윤거(Mean of tread)를 적용하여 속도 추정하는 방법(Case 4)에 대한 속도 추정정확도를 평가하였다. 4가지 방식 각각에 대해 현장에서 센서를 설치하고 기준값과 속도추정 값을 비교 분석을 했으며, 평가지표로는 등가계수(Equality Coefficient), 절대오차백분율(MAPE)을 통하여 평가하였다. 평가결과는 Case1 > Case 4 > Case 2, 3 순으로 양호한 결과를 보이는 것으로 분석되었다.

• Elastomers and Composites
• /
• 제29권5호
• /
• pp.431-435
• /
• 1994

For recycling of the waste tires, polyurethane binder mixed with the scrapped rubber powders which obtained from tread part of waste tire. This study covered the effect of the binder contents on the mechanical properties of the blend. We also studied the change of the properties after aging on properties compared with those of before aging. The curing reaction of the binder was also investigated in this study. We obtained conclusions the suitable binder content was 15phr in this system.

• 한국CDE학회논문집
• /
• 제20권2호
• /
• pp.104-113
• /
• 2015

In developing a tire, many CAE analyses are performed to make a better tire. But its meshing work is not easy, and it takes much time. One of the reasons of taking much time is that there are many overlapped geometric entities in CAD data that are modeled in CAD system by CAD engineers. In this study, we studied about the features of the overlapped geometric entities, and the method to find out and delete them. I developed a program using the proposed algorithm, and applied it in meshing tire pattern and tire case. I proved that the time in meshing a tire reduced dramatically by removing overlapped geometric entities by using the developed program.