• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.463-463
• /
• 2008

The glass frit has been used in transparent dielectric, barrier rib and electrode of PDP (Plasma display panel). In PDP fabrication, the firing temperature of glass frit is normally 550~$580^{\circ}C$ with conventional heating. However, there are a problem that silver in electrode is diffused throughout the transparent dielectric. For inhibiting the Ag diffusion we considered use of the microwave heating. We investigated firing of glass frit compared between conventional and microwave heating. After firing by two types of heating, the diffusion of silver is determined using a optical microscope and UV-spectrometer. Based on the our results, the microwave heating should be a candidate to heating source for high efficacy in PDP.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.4
• /
• pp.83-86
• /
• 2010

The transparent electrode properties of ITO films deposited by RF magnetron sputtering with process pressure were investigated. The ITO thin films was deposited on a glass substrate using a target with 3in diameter sintered at a ratio of $In_2O_3$ : $SnO_2$ (9 : 1). 200-nm-thick ITO thin films were manufactured by various process pressures ($2.0{\times}10^{-2}$, $7.0{\times}10^{-3}$ and $2.0{\times}10^{-3}$ Torr). The optical transmittance and resistivity of the deposited ITO thin films showed a relatively satisfactory result under $10^{-2}$ Torr. For high process pressure, the optical transmittance was below 80%, while for low process pressure, the optical transmittance was above 85%. As a result of of mobility, resistivity and carrier concentration by Hall measurement, we obtained satisfactory properties to apply into a transparent conducting thin film.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.408-411
• /
• 2003

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors, were prepared by using the capacitively coupled DC magnetron sputtering method. The influence of the substrate temperature, working gas pressure, discharge power and doping amounts of Al on the electrical, optical and morphological properties were investigated experimentally. The effect of bias voltage on the electrical properties of ZnO thin film were also studied. Films with lowest resistivity of $5.4{\times}10^{-4}\;{\Omega}-cm$ have been achieved in case of films deposited at 1mtorr, $400^{\circ}C$ with a substrate bias of +10V for 840nm in film thickness.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.1
• /
• pp.29-32
• /
• 2010

In this study, transparent and conductive Al-doped zinc oxide (AZO) films were prepared on a glass substrate by an radio frequency (RF) magnetron sputtering method using a 150-nm-thick AZO target (Al: 2 wt.%) at room temperature. We investigated the effects of RF power between 100-350 W (in steps of 50 W) on the structural, electrical, and optical properties of the AZO films. The thickness and cross-sectional images of the films were observed by field emission scanning electron microscopy. The thicknesses of all films were kept constant at 150 nm and grown on a glass substrate. The grain sizes of the AZO films were determined with the X-ray diffraction by using the Scherrer' equation, and their electrical properties were investigated using a Hall effect electronic transport measurement system. The transmittance of the AZO films was also measured by an ultraviolet-visible spectrometer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.939-942
• /
• 2004

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors were Prepared by using the capacitively coupled RF magnetron sputtering method. In this paper the effect of RF discharge power on the electrical, optical and structural properties were investigated experimentally. The results show that the structural and electrical properties of the film are highly affected by the variation of RF discharge power. The optimum growth conditions were obtained for films doped with 2 wt% of $Al_2O_3$ and 200 W in RF discharge power, which exhibit a resistivity of $10.4{\times}10^{-4}{\Omega}-cm$ associated with a transmittance of 89.66 % for 1000nm in films thickness in the wavelength range of the visible spectrum.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.4
• /
• pp.6-11
• /
• 2019

For a wider application of laser direct patterning, selective laser ablation of indium tin oxide (ITO) film on transparent oxide semiconductor (TOS) thin film was carried out using a diode-pumped Q-switched Nd:YVO₄ laser at a wavelength of 1064 nm. In case of the laser ablation of ITO on indium gallium zinc oxide (IGZO) film, both of ITO and IGZO films were fully etched for all the conditions of the laser beams even though IGZO monolayer was not ablated at the same laser beam condition. On the contrary, in case of the laser ablation of ITO on zinc oxide (ZnO) film, it was possible to etch ITO selectively with a slight damage on ZnO layer. The selective laser ablation is expected to be due to the different coefficient of thermal expansion (CTE) between ITO and ZnO.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.2
• /
• pp.57-60
• /
• 2018

Recently, Thin-film transistors (TFTs) are fundamental building blocks for state-of-the-art microelectronics, such as flat-panel displays and system-on-glass. Zinc oxide thin films have the advantage that they can grow at low temperature and can obtain high charge movility. Also the zinc oxide thin film can be used to control the resistance according to the oxygen content, so it is very easy to obtain the desired physical properties. In this paper, we fabricated a zinc oxide thin film on a polished copper substrate through a solution process, then improved the crystallinity through a geat treatment porcess, and studied to transfer it on a flexible substrate after the heat treatment was completed.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.1
• /
• pp.91-94
• /
• 2022

Top emission organic light-emitting diode is commonly used because of high efficiency and good color purity than bottom - emission organic light-emitting device. Unlike BEOLED, TEOLED contain semi-transparent metal cathode. Because of semi-transparent cathode, micro cavity effect occurs in TEOLED. We optimized this effect by changing the thickness of hole injection layer. Device consists of is indium-tin-oxide / N,N'-Di-[(1-naphthyl)-N,N'-diphenyl]-1,1'-biphenyl-4,4'-diamine (x nm) / tris-(8-hydroxyquinoline) aluminum (50nm) / LiF(0.5nm) / Mg:Ag (1:9), and we changed NPB thickness which is used as HTL in our device in order to study how micro cavity effects are changed by optical path. As the results, NPB thickness at 35nm showed the current efficiency of 8.55Cd/A.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1437-1439
• /
• 2009

Electrical and optical properties of $SiO_2$-doped ZnO (SZO) films on the corning 7059 glass substrates by using rfmagnetron sputtering method are investigated. The deposition rate becomes maximum near 3 wt.% and gradually decreases when the $SiO_2$ content further increases. The growth rates at 3 wt.% is $4^{\circ}$A/s. We found that the average transmittance of all films is over 80% in the wavelength range above 500 nm. The optical band gap decreases from 3.52 to 3.33 eV with an increase in thickness. X-ray diffraction patterns show that the film with a relatively low $SiO_2$ content (< 4 wt.%) is amorphous. SZO films at the $SiO_2$ contents of 2 wt.% shows the resistivity of about $3.8{\times}10^{-3}{\cdot}cm$. The sheet resistance decreases with increasing the heat treatment temperature.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.9
• /
• pp.1314-1318
• /
• 2012

Recently, applications of plasma display to the large public display and transparent display gain much attention. With this background, we report characteristics of opposite electrodes discharge cell with long electrode gap in comparison with conventional co-planar surface discharge. The cell size of test panel is $2950{\mu}m{\times}840{\mu}m$, which corresponds to that of the display having diagonal size of 130" with XGA resolution. Electrode gap of co-planar and opposite electrode structure are $240{\mu}m$ and $500{\mu}m$ respectively. These gap dimensions provide similar driving voltage windows. Experimental results show that opposite discharge provides approximately four fold higher luminous efficacy compared with that of the surface discharge. Resulting efficacy is found to be higher than 19 lm/W in green phosphor with 10 KHz continuous pulse operation.