• Korean Journal of Optics and Photonics
• /
• v.9 no.4
• /
• pp.240-244
• /
• 1998

Cavity ring-down spectroscopy (CRDS) is a high-sensitive laser spectroscopic technique capable of measuring concentrations of trace gases. We have demonstrated a new design of the CRDS spectrometer with a continuous wave (CW) laser. The ring-dwon signal is produced through blocking the incident CW laser by scanning the cavity length fast toward off-resonance iwth PZT (piezoelectric transducer). We have also measured an absorption spectrum of acetylene overtone transitions near 570 nm at the pressure of 2700 Pa, and the minimum detectable absorption coefficient has been found to be about $3{\times}10^{-9}\cm^{-1}$.

• Annual Conference on Human and Language Technology
• /
• 1999.10e
• /
• pp.128-134
• /
• 1999

기계번역이나 정보검색 등에 적용되는 자연언어처리기술에 있어서 구문분석은 매우 중요한 위치를 차지한다. 하지만, 문장의 길이가 증가함에 따라 구문분석의 복잡도는 크게 증가하게 된다. 이를 해결하기 위한 많은 노력 중에서 전처리기의 지원을 통해 구문분석기의 부담을 줄이려는 방법이 있다. 본 논문에서는 구문분석의 애매성과 복잡성을 감소시키기 위해 유한상태 변환기 (Finite-State-Transducer FSI)를 이용한 전처리기를 제안한다. 유한상태 변환기는 사전표현, 단어분할, 품사태깅 등에 널리 사용되어 왔는데, 본 논문에서는 유한상태 변환기를 이용하여 형태소 분석된 문장에서 시간표현 등의 제한된 표현들을 구문요소화하는 전처리기를 설계 및 구현하였다. 본 논문에서는 기계번역기에서의 구문분석기 뿐만 아니라 변환지식의 모듈화를 지원하기 위해 유한상태 변환기를 이용하여 시간표현 등의 부분적인 표현들을 번역하는 방법을 제안한다. 또한 유한상태 변환기의 편리한 작성을 위하여 유한상태 변환기 작성 지원도구를 구현하였다. 본 논문에서는 전처리기의 적용을 통해 구문분석기의 부담을 덜어 주며 기계번역기의 변환부분의 일부를 성공적으로 담당할 수 있음을 보여 준다.

• Nuclear Engineering and Technology
• /
• v.42 no.3
• /
• pp.319-328
• /
• 2010

Bonded tendons have been used in reactor buildings at some operating nuclear power plants in Korea. Assessing prestress force on these bonded tendons has become an important pending problem in efforts to assure continued operation beyond their design life. The System Identification (SI) technique was thus developed to improve upon the existing indirect assessment technique for bonded tendons. As a first step, this study analyzed the sensitivity of the key parameters to prestress force, and then determined the optimal parameters for the SI technique. A total of six scaled post-tensioned concrete beams with bonded tendons were manufactured. In order to investigate the correlation of the natural frequency and the displacement to prestress force, an impact test, a Single Input Multiple Output (SIMO) sine sweep test, and a bending test using an optical fiber sensor and compact displacement transducer were carried out. These tests found that both the natural frequency and the displacement show a good correlation with prestress force and that both parameters are available for the SI technique to predict prestress force. However, displacements by the optical fiber sensor and compact displacement transducer were shown to be more sensitive than the natural frequency to prestress force. Such displacements are more useful than the natural frequency as an input parameter for the SI technique.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.991-996
• /
• 2013

In this paper, the ultrasonic horn having the natural frequency with 60 [kHz] for the dissimilar material bonding of the glass and solder tried to be designed. The ultrasonic horn was designed through the relational formula including the aspect ratio of the input terminal and output terminal, length of the ultrasonic horn. The modal analysis was performed for the propriety analysis of the designed horn. The parameters and response was set through the basic experiment. The dissimilar material bonding strength analysis using the ultrasonic transducer was done. The optimal process parameters having maximum bonding strength was derived.

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.7
• /
• pp.431-438
• /
• 2010

The radiation pattern of conformal transducers installed on a curved surface is likely to be complicated depending on the array pattern on the curved surface. In this research, the acoustic sources constituting a conformal transducer are arrayed in equi-angle, equi-interval, and geodesic dome forms, and the radiation pattern function of each of the array geometries has been derived, and therewith the radiation pattern has been analyzed for each array geometry. Based on the analysis result, we have determined the equi-interval array geometry that provides the widest beam width with the lowest side lobe level among the three array geometries. Results of the present work are expected to be utilized to the design of conformal transducer structures.

• The Journal of the Acoustical Society of Korea
• /
• v.5 no.4
• /
• pp.37-45
• /
• 1986

초음파 Hyperthermia를 이용한 치료는 정상세포에 열적 손상을 주지 않으면서 종양 부위만을 적당한 온도로 가열하여야 하며 따라서 종양세포와 정상세포에 대한 정확한 초음파 세기조절이 필요하 게 된다. 본 논문에서는 초음파 Hyperthermia 용 변환기로서 초점거리와 가열범위를 전자적으로 쉽게 조절할 수 있는 동심환 배열 변환기를 설계하였으며 컴퓨터 모의 실험을 통해 그 성능을 예측하였다. 설계된 변환기는 유효직경 118mm, 동작주파수 320kHz 이며 배열 요소의 수는 12개이다. 그리고 이와 같은 동심환 변환기를 동작시키기 위해 카운터를 이용한 디지털 위상 조절 회로를 설계 제작하였으며, 실험 결과, 위상차를 갖는 신호를 발생시킬 수 있었다.

• 전기의세계
• /
• v.31 no.2
• /
• pp.141-146
• /
• 1982

In this paper, surface acoustic wave (SAW) bandpass filter is designed using the Fourier series approach and the I$_{0}$-shin window function. And also we studied a method to realize SAW filter using the apodized ID transducer which was fabricated with aluminum metallization of about 1500 A over .deg. thickness on Y-cut Z-propagating LiNbO$_{3}$, crystal by photolithographic technique (lift-off method). Experimental results on SAW bandpass filter responses show good agreements with the theoretical characteristics.s.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.184-188
• /
• 2001

본 논문에서는 다중대역 피드를 위한 직교모드 변환기를 설계하였다. 직교모드 변환기의 전체적인 모양은 사각 테이퍼진 형태이고, 18-20 GHz 에서 우원 편파와 좌원편파를 발생시키기 위해 테이퍼 부분에 2개의 측면포트를 두고, 직선포트는 30-45 GHz의 광대역에서 -20dB 이하의 반사계수를 가지도록 설계하였다. 직선포트에서의 반사계수 특성을 향상시키기 위해서 측면포트에 얇은 격막을 삽입하였다. 전체적인 설계에 상용소프트웨어인 HFSS$^{R}$를 사용하였다.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1348-1350
• /
• 1994

In this study, various nozzle of ultrasonic spray were designed by using Langevin type electrostriction transducer. The electrical and dynamic characteristics of ultrasonic nozzle with various horn type were investigated. We obtained the average particle size and size distribution profiles with output frequency.

• Journal of the Korea Society for Simulation
• /
• v.12 no.4
• /
• pp.17-24
• /
• 2003

In this paper, we propose a model that simulates the reflective waveform from underwater objects by means of Doppler effect, highlight and elongation phenomenon. Also, this paper presents a hardware Implementation of simulation model with the input and output parameters. The underwater target simulator consists of transducer, receiver, transmitter and control parts. According to the experimental results of the simulator, it carried out the performances of real target in response to transmission signal.