• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.891-896
• /
• 2002

Flat plate is susceptible to punching shear failure at the slab-column connection, which may cause catastrophic structural collapse. To prevent such brittle failure, strength and ductility of the connection should be ensured. However, since it is very difficult to experimentally simulate the actual load and boundary conditions of the flat plate system, it is not easy to obtain reliable information and data regarding to the strength and ductility of the flat plate-column connection. In the present study, numerical studies were performed for interior connections of continuous flat plate. The results were compared with the existing experiments, and the variations of bending moment, shear, torsional moment around the connection were investigated. Based on the findings of the numerical studies, the disadvantages of current design methods were discussed.

• Computers and Concrete
• /
• v.10 no.5
• /
• pp.489-505
• /
• 2012

This paper presents a simplified grid beam model for simulating the nonlinear response of reinforced concrete flat-plate structures. The beam elements are defined with nonlinear behavior for bending moment and torsion. The flexural stiffness and torsional strength of the beam elements are defined based on experimental data to implicitly account for slab two-way bending effects. A failure criterion that considers the interaction between the punching strength and slab flexural behavior is incorporated in the model. The effects of bond-slip of slab reinforcement on connection stiffness are examined. The proposed grid beam model is validated by simulating large-scale tests of slab-column connections subjected to concentric gravity loading and unbalanced moment. This study also determines the critical parameters for a hysteretic model used to simulate flat-plates subjected to cyclic lateral loading.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.19 no.3
• /
• pp.4462-4471
• /
• 1977

The governing differential equations for the tapered circular arch with fixed ends have been derived, and a numerical procedure for the solution of these equations have been developed. The governing differential equations were solved numerically by an initial value integration procedure and Shooting Methods for boundary value problems. The Rungekutta fourth order integration technique was used. The methods was programmed for a Cyber 73-18 computer System, and all esults were obtained on this computer. A detailed study has been made for a fixed arch with an angle of opening equal to 0.7 radian, and the results are presented in detail in tables and curves. It is hoped that the results presented herein is applied to the deformations of gives point from the tri-axial direction of tapered circular arch with fixed ends, bending moment, and torsional moment, and that at the same time results to be used for archwise structures in steel structure.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.213-216
• /
• 2005

A numerical analysis was performed for interior connections of continuous flat plate to analyze the effect of design parameters such as column section shape, gravity load and slab span on the behavioral characteristics of the connections. Through the parametric study, the variations of shear stress distribution around the connection were investigated. According to the result of numerical analysis, as the length of the cross section of column in the direction of lateral load increases and gravity load increases, the effective area and the maximum shear strength providing the torsional resistance decrease considerably. And as the slab span loaded with relatively large gravity load increases, the negative moment around the connection increases and therefore the strength of connection against unbalanced moment decreases.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.10a
• /
• pp.167-172
• /
• 1996

A Dual Mass Flywheel system is a evolution to the reduction of torsional vibration and impact noise occuring in powertrain when a vehicle is eit-her moving or idling. The name already explains what it is : The mass of the conventional single mass flywheel is divided. One section continues to belong to the mass moment of inertia of the engine-side. The ot-her section increass the mass moment of inertia of the transmission-side. The two masses are connected via a spring /damping system. This reduces the speed at which the dreaded resonance occurs to below idle speed. Since 1984 Dual Mass Flywheel has been de-veloped again and again. But the prosidures of de-velopment of D.M.F system didn't have had differe-nce from conventional clutch system's trial and err-or This paper presents the method for systematical design of D.M.F system with demensionless design variables of D.M.F system mass ratio between two flywheels λ. natual frequency rate of two flywheel s, ${\gamma}$and viscosity coefficient ζ. And experimental re-sults are used to prove these theoretical results.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.2 s.69
• /
• pp.257-265
• /
• 2004

The aim of this study is to investigate the inelastic buckling behavior of the beams under moment gradient using a line-type finite element method. The method is incorporated the non-uniform yielding of the cross-section caused by the presence of residual stress and accepted model of residual stress so called 'simplified' and 'polynomial' pattern is adopted in this study. The inelastic lateral-torsional buckling results obtained in this study is compared with the buckling results obtained from the design method based on the allowable stress method given in Korean Steel Designers Manual (KSDM 1995). This study have found that the design method in KSDM (1995) is conservative without and with intermediate bracing applied at the mid span of the beam, and there is some scope for improving the provisions of KSDM (1995)

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.182-194
• /
• 1999

Occupant injury in rear end impact is rapidly becoming one of the most aggravating traffic safety problems with high human suffering and societal costs. Although rear end impact occurs at relatively low speed , it may cause permanent disability due to neck injuries resulting from an abrupt moment, shear force , and tension/compression force at the occipital condyles. The analysis is performed for a combined occupant-eat model response, using the SAFE(Safety Analysis for occupant crash Environment) computer program. The computational results are verified by those from sled tests. A parameter study is conducted for many physical and mechanical properties. Seat design has been performed based on the design of experiment process with respect to five parameters; seat-back upholstery stiffness, torsional stiffness of the seat-back. An orthogonal array is selected from the parameter study. A good design has been found from the analysis results based on the orthogonal array. The results show that reductions of stiffness in seat-back upholstery and joint are the most effective for preventing neck injuries.

• Earthquakes and Structures
• /
• v.17 no.5
• /
• pp.435-445
• /
• 2019

The collapses of curved bridges are mainly caused by the damaged columns, subjected to the combined loadings of axial load, shear force, flexural moment and torsional moment, under earthquakes. However, these combined loadings have not been fully investigated. This paper firstly investigated the mechanical characteristics of the bending-torsion coupling effects, based on the seismic response spectrum analysis of 24 curved bridge models. And then 9 reinforced concrete (RC) and circular column specimens were tested, by changing the bending-tortion ratio (M/T), axial compression ratio, longitudinal reinforcement ratio and spiral reinforcement ratio, respectively. The results show that the bending-torsion coupling effects of piers are more significant, along with the decrease of girder curvature and the increase of pier height. The M/T ratio ranges from 6 to 15 for common cases, and influences the crack distribution, plastic zone and hysteretic curve of piers. And these seismic characteristics are also influenced by the compression ratio, longitudinal reinforcement ratio and spiral reinforcement ratios of piers.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.3
• /
• pp.299-311
• /
• 2003

This paper presents a finite element procedure to estimate the ultimate strength of space frames considering spread of plasticity. The improved displacement field is introduced based on the inclusion of second-order terms of finite rotations. All the non-linear terms due to bending moment, torsional moment, and axial force are precisely considered. The concept of plastic hinges is introduced and the incremental load/displacement method is applied for elasto-plastic analyses. The initial yield surface is defined based on the residual stress, and the full plastification surface is considered under the combined action of axial forces, bending and torsional moments. The elasto-plastic stiffness matrices are derived using the flow rule and the normality condition of the limit function. Finite element solutions for the ultimate strength of space frames are compared with available solutions and experimental results.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.2
• /
• pp.9-18
• /
• 1999

The seismic over-strength factor Ω is evaluated for 4-story reinforced concrete buildings in Korea, which has low seismic intensity. For this study, the seismic load suggested in' Aseismic guideline research- phase ll' (in Korea) is used. When 3D study-models are designed, span length and bay number are varied and accidental torsional moment is considered. And the models are analyzed by push-over analysis, in which external and internal frame are connected by rigid-link. As a result of numerical experiments, Ω is increased as the bay number or span length is increased. Because, by the including of accidental torsional moment in designing process, the increased ratio of strength of external columns is larger than the increased ratio of span length or bay number. And this makes the failure mode of model closer or strong-column and weak-beam mechanism.