• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.4
• /
• pp.671-678
• /
• 2020

In this paper, a wireless measurement system has been developed which can measure the deformation of a tire in real time by utilizing strain gauge sensors and Zigbee wireless communication. A strain gauge sensor is mounted inside the tire and then the strain on the tire is obtained using the DSP module. The acquired sensor values are transmitted into the vehicle by radio communication. The wireless receiver module installed inside the vehicle can monitor the deformation of the tire in real time. The deformation of the tire can be used for measuring the load applied to each tire or the speed of the tire. The load or speed applied to the tires are essential parameters for the stable control of autonomous vehicles.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.1
• /
• pp.49-55
• /
• 2007

In order to utilize treads of waste tire as reinforcement material it is necessary to know the interface friction angle between tread surfaces and soil and tensile strength of connection joint of tire treads. In this research large direct shear tests were performed to get the interface friction angle between the inner and outer surfaces of treads and soil for different degree of compaction. From the large direct shear tests, the ratio of interface friction angle to the shear friction angle of sand, ${\delta}/{\phi}$, were 1.06 in outside surface of tire tread and 0.93 in inside surface of tire tread. For weathered granite soil the ratio of interface friction angle was 0.98 and 0.92 for outside and inside of tread, respectively. Also tensile tests were performed using universal testing machine for the connection joint of treads and Tirecell units using bolts. The tensile strength of connection joint increased with the number of bolts and with the sizes of washers. Connection by polypropylene ropes showed lower strength than those of bolts.

• Textile Coloration and Finishing
• /
• v.29 no.2
• /
• pp.97-103
• /
• 2017

Polyketone fiber, a newly developed high strength fiber, has a tenacity and modulus similar to the p-aramid fiber, and can be used for reinforcing mechanical rubber goods(MRG), such as tires, hoses, and technical textiles. It will be expected for replacement of super fiber such as aramids and increasing the technical textile market share. This paper surveys the mechanical properties of polyketone fiber for technical textiles. For this purpose, dyed polyketone fabric is prepared, mechanical properties of coated and uncoated polyketone fabrics such as tensile strength, elongation and tear strength were examined before and after weather resistance test(temperature $63{\pm}3^{\circ}C$, humidity 60%, amount of power $0.35w/m^2$). The differences of mechanical properties between uncoated and coated fabrics for high functional technical textiles and composite materials are estimated through this study. The UV-stability of polyketone fabric showed obvious improvement after coating. After 168h(7day) of UV exposure, the coated fabric showed less deterioration in mechanical properties with the retained tensile strength and elongation at break greater than 22 and 17% of the uncoated polyketone fabrics values, respectively.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.5
• /
• pp.581-587
• /
• 2016

Braking is a basic and an important safety feature for all vehicles, and the final braking performance of a vehicle is determined by the vehicle's ABS performance and tire performance. However, the combination of excellent ABS and tires will not always ensure good braking performance. This is due to the fact that tire performance has non-linearity and uncertainty in predicting the repeated increase and decrease of wheel slip when activating the ABS, thus increasing the uncertainty of tire performance prediction. Furthermore, existing studies predicted braking performance after using an ABS that used a wheel slip control as a controller, which was different from an actual vehicle's ABS that controlled angular acceleration, therefore causing a decrease in the prediction accuracy of the braking performance. This paper reverse-designed the ABS that controlled angular acceleration based on the information on brake pressure, etc., which were obtained from vehicle tests, and established a braking performance prediction analysis model by combining a multi-body dynamics(MBD) vehicle model and a magic formula(MF) tire model. The established analysis model was verified after comparing it with the results of the braking tests of an actual vehicle. Using this analysis model, this study analyzed the braking effect by vehicle factor, and finally designed a tire that had optimized braking performance. As a result of this study, it was possible to design the MF tire model whose braking performance improved by 9.2 %.

• Journal of Biosystems Engineering
• /
• v.34 no.2
• /
• pp.71-76
• /
• 2009

This study was conducted to investigate the load acting on a tractor engine when it delivers the maximum power at drawbar. The results of the drawbar tests on the 5 locally-made and 14 imported tractors conducted at NIAE in 2004, and the 15 tractors tested at OECD test stations in foreign countries were analyzed and presented by the torque load ratio, defined as a ratio of the engine torque load caused by drawbar pull to its full-load capacity, as a function of pull speed. The NIAE test results showed that the torque load ratio increased from 20 to 80% with pull speed less than 5 km/h. At speeds faster than 5 km/h, it was 80${\sim}$110% regardless of the pull speed. However, the OECD test results showed that the torque load ratio was evaluated mostly to be 70${\sim}$90% in the entire pull speed range. The same trend was also shown for the maximum drawbar load. The difference in the torque load ratio may be attributable to bias-ply tires for locally-made and some imported tractors. It is also suggested that the input torque load may be increased safely up to 120% of the full load capacity of the tractor engine for an accelerated life test of tractor transmissions.

• Resources Recycling
• /
• v.4 no.4
• /
• pp.59-69
• /
• 1995

Distillation oI the dust generated during waste tue pyrolysis was perIomerl to rccover valuable metal sucll as zlnc. lead and iron. Pemcahilily and carnprcssivc tests were pursucd to ahlain the basic dala for cslraclian of zinc from the slntering propcrtp ol stccl making dusts and distilled carhon of waste tires as wcll as wastc pulp sludge mixlure hr~quet were investigated at various sinlcring lempcraturcs. Permeablllly rncieased with increastng amount of waste pulp in specil~cd istilled carhon due tn the fnrmat~ono f porusily in lhe sample TIE co~npress~vsctr ength showed the vanous values wlth different amDunl of dislilled-carhon adrlit~nilsa nd at diIIerenl sinlering tcmpcralures. X-ray diffifraction anvlyscs oI a hnquet rn~rhtre of steelmaking dusts(20Q didilled carhon and 10% waste pulp sblered ;>I SOOT) showcd thal the briquet consisted ot ZnO and Fc,O.,, hut was not found at the hriguet rintered at over 10OO'C. Crude zinc oxide sintered a1 IOOOC contained OZA Zn.

• Resources Recycling
• /
• v.23 no.4
• /
• pp.30-36
• /
• 2014

300,000 tons of waste tires are annually being produced with development of the automotive industry in Korea. Landfill and incineration treatment system are causing the economic problem through secondary environmental pollution and waste. Therefore, as one of the ways to take advantage of this, Thermo-Plastic Vulcanized (TPV) composite was prepared by the ground waste tire and plastic powders. The waste tire powder was gained by mechanical fracturing through crushers. The waste tire powder was ground by a shear crushing method and a 2-stage disk mill method instead of cutting crushing one. The waste tire powder of 50 mesh was mixed with Polypropylene(PP) in various proportions. TPVs were prepared by an extrusion, and tensile and impact tests were performed. In addition, the same experiments were repeated in 40, 80, 140 mesh conditions in order to observe size effect of waste tire powders.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.59-67
• /
• 2009

With the development of high-cost vehicle detectors, low-cost detectors have also been studied due to the advantage that more detectors are provided within limited budgets. This study proposed a method to estimate vehicle speeds using vehicles' track data from auto manufacturers and time stamps obtained when vehicles' tires pass an inclined sensor (here, a tape switch sensor). In speed estimation, small vehicles and large vehicles is distinguished according to the ratio of time stamps for a wheelbase and a rear track obtained from a tape switch sensor. In particular, speed estimation can be adjusted through a parameter to determine vehicles' size so as to take into account location properties such as vehicles' classification ratio. The low-cost vehicle detector with an inclined sensor proposed in this study is expected to be widely utilized to monitor traffic conditions thanks to low cost.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.29-38
• /
• 1997

The effect and control of wood property of reconstituted composite panels for improved board properties by wood-waste materials and development of combination method for heterogeneous materials have been of interest to the wood science researchers. The purpose of this study is to consider the properties in relation to hot pressing conditions and to develope the optimum hot pressing condition with waste wood and waste tire for the manufacturing of composite boards. The study of composite boards for recycling of wood and waste tire is nothing up to the present. Physical and mechanical properties such as specific gravity, moisture content, swelling coefficient, modulus of rupture and modulus of elasticity in bending test were studied. The condition of 3-stage press time for the lowest moisture content of composite board was $4{\rightarrow}3{\rightarrow}3$ minutes. Specific gravity of composite panels was affected mainly by the amount of rubber chip. Because of the low rigidity and high elasticity in rubber chip, it is considered the composite panel was adequate material in the place of compression load, but not bending load. Therefore, it was concluded that a use of rubber-based wood composite panel is proper to the interior materials such as floor a room than exterior materials. From the test results, the most optimum hot pressing conditions were $4{\rightarrow}3{\rightarrow}3$ minutes for 3-stage press time and $45{\rightarrow}20{\rightarrow}5kg/cm^2$ for 3-stage press pressure. The rubber-based wood composite panel was very excellent in elasticity by combination of rubber chip in comparison with existing other wood-based materials. Therefore, it was considered that rubber-based wood composites can be applicable to every interior materials such as floor a room and will be expected to effective reuse and recycle of waste tires and wood-waste materials, and will be contribute to protection of environment pollution in earth.

• Economic and Environmental Geology
• /
• v.32 no.6
• /
• pp.633-644
• /
• 1999

Gully pot is a part of urban darainage system to butter the runoff water fluxes from road to rivers and to minimize environmental pollution by prevending over the surrounding area. A series of studies have been carried out concerning the physicochemical characteristics of the sewage sludge sediments sttling down in such a gully pot in order to over to evaluate the contamination for heavy metals such as pb, Zn, Cu and Cd. The roadside soil and sewage sludge samples from gully pots were characterized by XRD analyses and sequential extraction : Zn 2595.7$\mu$g/g; Cd9.8$\mu$/g; Cu602.5$\mu$g/g; Pb260.0$\mu$g/g),because of a long-term accumulation of vehicle- and industrial-related pollutants. Mean Zn concentration in Yeouido (3873$\mu$g/g) and Junggu(3262$\mu$g/g)areas are 4-5 times higher than those in Dobonggu area, suggesting that Zn may be derived from automobile traffic (including the rubber of automobile tires). The mean concentrations of Cu and Cr are very significantly high in Junggu and Gurogu areas, possibly due to the industrial activities in these areas. The low Pb levels throughtotut the whole study areas in Seoul can be accounted for the use of unleaded gasoline since 1987. Sequential extraction experiments illustrate that a major part of Zn is bound to FII and FIII, representing about 88% of the total Zn concentration. Fraction IV, related to orgnic matter, is mostly significant for Cu accounting for 60% of the total Cu, and FII is next in importance. The main carriers of Pb are the fractions III, II and FIV, and in that order. The behavior of Cd is quite different from other elements (Zn, Cu, Pb), and most of the Cd is associated with FV. Changes in the physicochemical environments (such as acidification) may result in severe environmental pollution of surface water and rivers with respect to heavy metals (especially Zn and Cu).