• Resources Recycling
• /
• v.14 no.4 s.66
• /
• pp.22-33
• /
• 2005

Four sheet-shaped and one soft-shaped self-sealing waterproof materials were prepared to recycle some GRT(Ground Rubber Tires). Their physical properties were tested to consider characteristics of them. The self-sealing waterproof materials were consisted of GRT/super absorbent polymer(SAP)/binder and mold by a hot press after mixing with a batch-typed internal mixer. The average size of GRT particles was -40 mesh, SAPs were commercial GE-500F and poly(AM-SAS-AA) prepared in this work. Binders were PU. EVA, LDPE, SBR, and poly(2-EHA). And PU film was attached to improve the properties of waterproof materials. Characteristics of self-sealing waterproof materials consisted of by GRT/GE-500F/EV-600/PU film and GRT/GE-500F/SBR(vulcanization)/PU film among the developed self-sealing waterproof materials were similar to the commercial products. And properties of the soft-shaped self-sealing waterproof materials consisted of by GRT/GE-500F/Po1y(2-EHA) and CRT/Poly(AM-SAS-AA)/poly(2-EHA) were improved within from four times to twenty times compared to the one oi the commercial products.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.3
• /
• pp.107-117
• /
• 2004

This paper is to investigate the reinforcing effects of newly devised Tire-cell mat made of waste tires in sand. Parametric study on number of connection bolts between Tirecells, relative density of sand, embedded depth, number of reinforced layers and width of Tirecell mat was made by using plate loading tests. It is found that the number of connection bolt was enough to maintain the given pressure. The bearing capacity ratio(BCR), which is defined as the rate of ultimate bearing capacity of reinforced soil to that of unreinforced soil, is the highest at the lowest density. And the reinforcing effect can be obtained in case of embedded depth within 1.0B, where B is loading width. Also settlement reduction is the highest at the lowest density of sand. The effect of number of Tirecell reinforced layers with 0.4B to 0.5B interval is limited to 2 layers and further reinforcing effects can not be obtained beyond 3 layers. Especially, the bearing capacity increased remarkably at 1 layer of reinforcement and the degree of increase was small from 1 layer to 2 layers of reinforcement. The effect of mat width of Tirecell was not significant because of high stiffness of Tirecell although the maximum bearing capacity was shown at the 2.0B mat width and the reinforcing effects of Tirecell, in general, was prominent compared with those of commercial Geoweb.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.33-39
• /
• 2020

In this paper, we propose the design technique of the vehicle's load weight measuring system using tire pressure, which is one of the physical elements of tires. The proposed technique consists of four processes: noise correction by load and vibration, gas flow correction, data mixer and weight conversion. Noise correction by load and vibration eliminates noise that increases the tire's internal pressure due to external shocks and vibrations produced by the vehicle while it is in motion. In the gas flow correction process, the noise of the internal pressure of the tire is increased due to the temperature rise of the ground with respect to the data obtained through the noise correction process due to the load and vibration. In the data mixer process, the load and pressure on the tolerances the empty, median and the full load are classified according to the change in pressure of the tire that is delivered perpendicular to the tire in the event of cargo. In the weight conversion process, weight is expressed by weight through weight conversion algorithms using noise correction results by load and vibration and gas flow correction. The weight conversion algorithm calculates the weight conversion factor, which is the slope of the linear function with respect to the load and pressure change, and converts the weight. In order to evaluate the accuracy of the loading weight measurement system of the vehicle using the tire pneumatic system technique proposed in this paper, we propose the design technique of the vehicle's load weight measuring system using tire pressure, which is one of the physical elements of tires.. Noise correction results by load and vibration and gas flow data correction results showed reliable results. In addition, repeated weight precision test showed better weight accuracy than the standard value of 90% of domestic companies.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.5
• /
• pp.57-66
• /
• 2022

The Road Management Administration is cracking down on overloaded vehicles by installing low-speed or high-speed WIMs at toll gates and main lines on expressways. However, in recent years, the act of intelligently evading the overloaded-vehicle control system of the Road Management Administration by illegally manipulating the variable axle of an overloaded truck is increasing. In this manipulation, when entering the overloaded-vehicle checkpoint, all axles of the vehicle are lowered to pass normally, and when driving on the main road, the variable axle of the vehicle is illegally lifted with the axle load exceeding 10 tons alarmingly. Therefore, this study developed a technology to detect the state of the variable axle of a truck driving on the road using roadside camera images. In particular, this technology formed the basis for cracking down on overloaded vehicles by lifting the variable axle after entering the checkpoint and linking the vehicle with the account information of the checkpoint. Fundamentally, in this study, the tires of the vehicle were recognized using the Mask RCNN algorithm, the recognized tires were virtually arranged before and after the checkpoint, and the height difference of the vehicle was measured from the arrangement to determine whether the variable axle was lifted after the vehicle left the checkpoint.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.6
• /
• pp.622-628
• /
• 2013

Due to the development of compounding technology, there is a considerable increase in the number of high performance rubbers in the world. Accordingly, there are rapid growing requests about high performance tires such as UHP tire and Run-flat tire. However, it is extremely difficult to investigate the friction coefficient of tire tread rubbers. An alternative solution must be developed with the reliability of high-speed linear friction test machines. The use of friction test machines can be expected to improve rubber friction researches. In this paper, we propose a new kind of high-speed linear friction test machine. We have designed and manufactured various mechanisms for friction tests. The final goals are to design and manufacture friction test machines that can investigate friction coefficients efficiently and rapidly. The performance of the proposed high-speed linear friction test machine is evaluated experimentally; however additional study should be necessary for safer and more reliable experimentation.

• Asian-Australasian Journal of Animal Sciences
• /
• v.6 no.3
• /
• pp.389-394
• /
• 1993

A study on housing and management of dairy cows was conducted in three villages. All activities of husbandry related to the housing and the condition of the cows were observed and farmers were interviewed using a questionnaire. The main type of housing was a tie stall mostly in the back yard area with a gable or shed type roof. Inside the shed the temperature ranged from 17 to $29^{\circ}C$ and the relative humidity ranged from 62 to 73%. Drainage and manure handling was poor which lead to poor cleanliness of the stables and animal skins. The floor space was mostly wide and the roof level was low (less than 2.5 m). The slope of the floor (1-3%) was sufficient, the roughness of the floor was of medium quality. The shape and size of the feed trough was good with a surface of mostly irregular forms. Concentrate was mixed with water and offered in liquid form in pails made from plastic or from parts of rubber car tires. Hoof length was too long which could lead to unstable position and self injury. It is concluded that the housing conditions of dairy cattle need to be improved in order to improve the condition of the animals and the production performance.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.2
• /
• pp.203-209
• /
• 2016

According to the wear detection history for the steam generator tubes in the nuclear power plant, the outer tubes inside the steam generator have more problems on the flow-induced vibration than inner tubes. Many researchers and engineers have used a specified added mass coefficient for a given tube array during the design stage of the steam generator even though the coefficient is not constant for entire tube in cylindrical shell. The aim of this study is to find out the distribution of added mass coefficients for each tube along the radial location. When numbers of tubes inside a cylindrical shell are increased, values of added mass coefficients are also increased. Added mass coefficients at outer tubes are less than those of inner tubes and they are decreased with increasing the gap between the outermost tube and the cylindrical shell. It also turns out when the gap between the outermost tube and the cylindrical shell approaches infinite value, the added mass coefficient converges to an asymptotic value of given tube array in a free fluid field.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.89-94
• /
• 2006

The tire delivering power generated from engine to the ground pulls a vehicle to move. Radius of tires is changeable due to elasticity that depends on the speed of vehicle and traction force. The main objectives on this study are real time measurement of dynamic radius and slip ratio according to the speed and traction force. The dynamic radius is proportional to speed and traction force. According to measurement, the dynamic radius is increased about 3mm under 100km/h compared to stop. It is also increased about 1.5mm when a traction force is supplied as much as 4kN compared to no load state at low speed. There is no strong relationship between slip ratio and vehicle speed. The slip ratio is measured up to 4% under WOT at first stage gear. Through this research, the method of measuring dynamic radius and slip ratio is set up and is expected to be applied to the measurement of traction force in chassis dynamometer or accelerating and climbing ability.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.169-176
• /
• 2000

Longitudinal and lateral forces acting on tires are known to be closely related to the tract-ability braking characteristics handling stability and maneuverability of ground vehicles. In thie paper in order to develop tire force monitoring systems a monitoring model is proposed utilizing not only the vehicle dynamics but also the roll motion. Based on the monitoring model three monitoring systems are developed to estimate the tire force acting on each tire. Two monitoring systems are designed utilizing the conventional estimation techniques such as SMO(Sliding Mode Observer) and EKF(Extended Kalman Filter). An additional monitoring system is designed based on a new SKFMEC(Scaled Kalman Filter with Model Error Compensator) technique which is developed to improve the performance of EKF method. Tire force estimation performance of the three monitoring systems is compared in the Matlab simulations where true tire force data is generated from a 14 DOF vehicle model with the combined-slip Magic Formula tire model. The built in our Lab. simulation results show that the SKFMEC method gives the best performance when the driving and road conditions are perturbed.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.3
• /
• pp.20-29
• /
• 2009

This study investigated the shear strength characteristics of waste tire powder-added lightweight soil (WTLS), which were developed to recycle dredged soil, bottom ash, and waste tires. The WTLS used in this experiment consisted of dredged soil, bottom ash, waste tire powder, and cement. Test specimens were prepared with various contents of waste tire powder ranging from 0% to 100% at 25% intervals and bottom ash contents of 0% or 100% by the weight of the dry dredged soil. In this study several series of direct shear tests were carried out, which indicated that the shear properties of WTLS were strongly influenced by the mixing conditions, such as the waste tire powder content and bottom ash content. The unit weight, as well as the shear strength of the WTLS, decreased with an increase in waste tire powder content. The shear strength of WTLS with bottom ash was 1.34 times greater than that of WTLS without bottom ash. An average increase in cohesion of 30 kPa was obtained in WTLS with the inclusion of bottom ash due to the bond strength induced from the pozzolanic reaction of the bottom ash. In this test, the maximum value of the internal friction angle was obtained with a 25% content of waste tire powder.