• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.5
• /
• pp.905-909
• /
• 2007

Crystalline and micro-structural characteristics of ZnO thin films which were deposited on p-Si(100) with cooling naturally down of pre-heated substrate during RF magnetron sputter deposition, were investigated by XRD and SEM in this paper. The film which was prepared on the substrate which was pre-heated to $400^{\circ}C$ before deposition and then cooled naturally down during deposition, showed the most outstanding c-axis preferred orientation. The ZnO thin film having the best crystalline result were applied to SMR type FBAR device and resonance properties of the device were investigated by network analyzer. It showed that resonance frequency was 2.05 GHz, return loss was -30.64 dB, quality factor was 3169 and electromechanical coupling factor was 0.4 %. This deposition method would be very useful for application of surface acoustic wave filter or film bulk acoustic wave resonator.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.2
• /
• pp.174-177
• /
• 2009

In this paper, an oscillator using dielectric-rod loaded cavity resonators with HTS(High Temperature Superconductor) end-plates was presented. It was operated at X-band. A two port cavity resonator was incorporated into a basic feedback loop oscillator configuration. A rutile loaded cavity resonator with HTS thin film end-plates was used to provide the quality factor between $10^4$ and $10^6$. A parallel feedback oscillator was constructed with a dielectric loaded cavity resonator, an amplifier, and a directional coupler. At 300 K, the experimental results showed the phase noise of -108 dBc/Hz at a 100 kHz offset frequency. At 26 K, the results was -118.8 dBc/Hz at same offset frequency.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.581-584
• /
• 2002

In this work, a CPW resonator was designed and fabricated to investigate the basic microwave properties, such as effective dielectric constant, of BST thin films. Their properties were used as basic data to simulate and design CPW tunable bandpass filter. We also report on gold/$Ba_{0.5}Sr_{0.5}TiO_3$(BST) ferroelectric thin film C-band tunable bandpass filters(BPFs) designed and fabricated on magnesium oxide substrates using CPW structure. The 2 pole filter was designed for a center frequency of 5.88 GHz with a bandwidth of 9 %. The BST based CPW filter offers a high sensitivity parameter as well as a low loss parameter. The tuning range for the bandpass filter with CPW structure was determined to be 170 MHz.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.56-56
• /
• 2003

최근 정보통신 분야의 급격한 발달로 인하여 무선통신에 사용되는 주파수 영역 또한 계속 높아짐에 따라 대역통과 필터 소자의 삽입 손실, 소비 전력, 크기, MMIC화에 대한 많은 연구가 진행되고 있다 압전 현상을 이용한 박막형 공진기가 이러한 요구를 충족시키고, 현재의 SAW filter를 대체할 소자로 떠오르고 있다. 본 실험에서는 단결정 미세 구조를 만들 수 있고, 압전 효과 또한 우수하며, Surface Micromachining보다 비교적 제조 공정이 간단하고 선택적 에칭이 가능한 Bulk Micromachining을 이용하여 Si$_3$N$_4$ Membrane을 이용한 중심주파수 5.2GHz인 두께 진동모드 Film Bulk Acoustic Wave Resonator(FBAR)를 제작하고 공진기의 고주파 특성을 평가하였다. Membrane구조 형성을 위해 Backside면인 Si$_3$N$_4$, Si은 RIE(Reactive Ion Etching)와 선택적 에칭용액인 KOH로 각각 에칭하여 Membrane을 갖는 구조로 중심주파수 5.2GHz인 두께 진동모드 FBAR를 설계 및 제조하였다. 체적 탄성파 공진 현상은 r.f Magnetron Sputtering법으로 증착한 AIN 압전박막과 Mo전극으로부터 발생 가능하였다. 본 연구에서는 0.9$\mu\textrm{m}$-Si$_3$N$_4$ Membrane을 이용해 FBAR를 제작/평가하고, RIE을 통해 Membrane을 제거해 가면서 공진기의 특성 즉, Quality factor와 유효전기기계결합계수(K$_{eff}$) 및 S parameter특성을 비교 측정해 보았다. 측정해본 결과 Membrane Free일때가 훨씬더 공진 특성이 우수함을 볼 수 있다

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.41-42
• /
• 2005

The characteristics of ZnO films are reported depending on different deposition conditions for film bulk acoustic resonators (FBARs). The ZnO films have been deposited on Al films evaporated on p-type (100) silicon substrate by pulsed laser deposition (PLD) technique using a Nd:YAG laser. These films exhibit an electrical resistivity higher than $10^7$ $\Omega$m. X-ray diffraction measurements have shown that ZnO films are highly c-axis oriented with full width at half maximum (FWHM) below $0.5^{\circ}$. These results show the possibility of FBAR devices using by PLD.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.2
• /
• pp.152-155
• /
• 2007

In this study, we fabricated FBAR(film bulk acoustic resonator) by using $Li_{2}CO_{3}:ZnO$ as a function of annealing temperature and concentrated on effect of frequency characteristic of FBAR. The results show that the annealing affects resistivity and crystallity. The optimum properties were observed for film annealed at $500^{\circ}C$. The resistivity was $1.5{\times}10^{11}\;{\Omega}{\cdot}cm$ and the roughness was 21.10 nm. And the return loss is improved from -24.9 at $300^{\circ}C$ to -29.8 at $500^{\circ}C$ without the resonant frequency change. We finally confirmed the improvement on the frequency characteristics of FBAR device by annealing process at the optimized condition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.309-310
• /
• 2006

In this paper, frequency characteristic of FBAR was studied as a function of annealing temperature. we have used Li dopant to enhance electrical properties of ZnO thin film. Li:ZnO thin film was deposited on Al(300 nm)/$SiO_2$(500 nm)/Si($500\;{\mu}m$) and each layer was patterned. Thermal treatment was executed in range of between 300 and $600^{\circ}C$ in $O_2$ ambient. We observed that the resistivity of ZnO is enhanced under the influence of Li doping and return loss in FBAR frequency properties is improved through annealing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.112-112
• /
• 2009

In this study, the effect of a long post-deposition thermal annealing(600 and 1000 $^{\circ}C$) on the surface acoustic wave (SAW) properties of polycrystalline (poly) aluminum-nitride (AlN) thin films grown on a 3C-SiC buffer layer was investigates. The poly-AlN thin films with a (0002) preferred orientation were deposited on the substrates by using a pulsed reactive magnetron sputtering system. Experimental results show that the texture degree of AlN thin film was reduced along the increase in annealing temperature, which caused the decrease in the electromechanical coupling coefficient ($k^2$). The SAW velocity also was decreased slightly by the increase in root mean square (RMS) roughness over annealing temperature. However, the residual stress in films almost was not affect by thermal annealing process due to small lattice mismatch different and similar coefficient temperature expansion (CTE) between AlN and 3C-SiC. After the AlN film annealed at 1000 $^{\circ}C$, the insertion loss of an $IDT/AlN/3C-SiC/SiO_2/Si$ structure (-16.44 dB) was reduced by 8.79 dB in comparison with that of the as-deposited film (-25.23 dB). The improvement in the insertion loss of the film was fined according to the decrease in the grain size. The characteristics of AlN thin films were also evaluated using Fourier transform-infrared spectroscopy (FT-IR) spectra and X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM) images.

• Journal of information and communication convergence engineering
• /
• v.5 no.4
• /
• pp.316-319
• /
• 2007

This paper presents some methods to improve the resonance characteristics of film bulk acoustic-wave resonator (FBAR) devices. The FBAR devices were fabricated on multilayer Bragg reflectors (BR) into which very thin chromium (Cr) adhesion layers were inserted, followed by several kinds of thermal annealing processes. These methods resulted in an excellent device improvement in terms of return loss and Q-factors.

• Journal of the Korean Ceramic Society
• /
• v.37 no.12
• /
• pp.1198-1203
• /
• 2000

AlN와 Si을 이용하여 체적 탄성파 over-moded 공진기를 형성하였다. 높은 c-축 배향성을 갖는 AlN 압전박막은 sputtering에 의해 저온에서 증착하였다. AlN 박막의 c-축 배향성은 기판과 타겥의 거리가 가까울수록, 증착 압력이 낮을수록 (002) 면으로의 성장이 촉진되었다. Si 기판을 이용한 over-moded 공진기로부터 TFR의 임피던스를 산출한 결과 공진영역의 면적에 가장 의존하였다. Al/AlN/Al로 이루어진 TFR의 입력 임피던스는 공진 영역이 크기가 200㎛×200㎛인 경우 가장 50Ω에 근접하였다. Over-moded 공진 특성은 Si 기판의 낮은 Q로 인해 mode 수 294인 2.60976 GHz에서 0.109%의 유효 전기기계결합계수(K/sub eff/²)와 0.3의 K/sub eff/²·Q값을 보였다.