• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.155-155
• /
• 2009

This paper introduces the findings of a detailed study on breakdown voltage strength under DC voltage and the development of HVDC cable. Recently, Nano-fillers are attracting attentions of many researchers and engineers, since they seem to bring higher potentials for advancement of electrical insulating properties as nano-composites. Additives and fillers are often adopted to polymeric materials for improving insulating and machanical properties. We have improved the polymer composition and developed a new insulation material for HVDC cable. Each specimen blended at LDPE1 to antioxidant, LDPE2 to antioxidant, pure XLPE was manufactured respectively. The insulation performances of the proposed insulator were compared with specimens blended at nano powders. DC breakdown strength of LDPE1 specimen at 90[$^{\circ}C$] was higher than other specimens. The experimental results show that polar groups intorduced in moleculars chains of blended specimen plays an important role in enhancement of thermal conductivity.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.10
• /
• pp.1688-1693
• /
• 2016

In this study shall investigate the influence upon the electrical property of transformer oil due to the heat among accelerated heat degradation experiment for a constant hour in the typical insulation oils of mineral base oil, silicon base oil and vegetable oil. In addition, the electric insulation performance of insulation materials in transformer shall be evaluated through the electric property analysis according to the heat degradation of epoxy insulation material, which has been used for electric facilities such as a molded transformer.

• Electrical & Electronic Materials
• /
• v.10 no.8
• /
• pp.800-806
• /
• 1997

The behavior of de levels in rapid thermal annealed Fe-doped semi-insulating InP(100) was studied by photoinduced current transient spectrocopy(PICTS). In bulk InP, T2(Ec-0.24 eV), T3(Ec-0.30 eV) and T5(Ec-0.62 eV) traps were observed. After annealing the T2 trap was annihilated at 20$0^{\circ}C$ and recreated at 35$0^{\circ}C$. T3 trap was not affected below 40$0^{\circ}C$. With increasing temperature the concentration of T5 trap reduced and it was annihilated at 30$0^{\circ}C$. However the T1(Ec-0.16 eV) and T4(Ec-0.42 eV) traps were began to appear at 40$0^{\circ}C$and these concentrations were increased with annealing temperature. The T1 and T4 traps seem to be related to the isolated phosphorus vacancy( $V_{p}$) and $V_{p}$-indium antisite( $V_{p}$- $P_{in}$ ) or $V_{p}$-indium interstitial( $V_{p}$-I $n_{I}$) respectiely.respectiely.

• Journal of the Korean Ceramic Society
• /
• v.56 no.5
• /
• pp.468-473
• /
• 2019

This study focused on manufacturing an inorganic insulation material set with various amounts of calcium-sulfoaluminate (CSA) (hauyne) content for enhancing both workability (demolding, handling) and the high thermal insulating property. To carry out the experiment, the amounts of CSA utilized were 5%, 10%, 15%, and 20%, with anhydrous gypsum added in equal proportion to produce a stable formation. As the content of CSA increased, a sinking phenomenon occurred because of the hydration reaction from the slurry, so it was difficult to utilize a retarder normally used in the cement manufacturing process. However, an RCOOM surfactant was able to solve the local clumping problem from cement and CSA and obtain a rapid retarding effect, so it was included in this process at 0.3%. Furthermore, the cement fineness was not 7000 ㎠/g but rather 3300 ~ 4000 ㎠/g to prevent a rapid temperature increase in the slurry. The specific gravity of the sample manufactured with 20% CSA was approximately 0.11 g/㎤, and its thermal conductivity was 0.041 W/m·K, providing an excellent insulating property.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.5
• /
• pp.326-331
• /
• 2015

In this paper, we study the insulating properties of the liquid nitrogen(LN2) including the thermal bubbles. The shape of the thermal bubbles in accordance with the current change was observed in the 77 K and 65 K LN2. According to the temperature of liquid nitrogen, bubbles were generated differently. The round shape of the bubble is occurred in 77 K LN2. But the layer shape of bubble is occurred in 65 K LN2. When the bubbles present, the dielectric strength of liquid nitrogen is low. However, the breakdown patterns were different according to the electrode arrangement. AC breakdown voltage(BDV) was lower than the DC BDV due to the influence of bubbles. Therefore, the design of a high-voltage superconducting equipments should consider the bubbles.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12
• /
• pp.1136-1141
• /
• 2003

The primary insulation materials used in an oil filled transformer are kraft paper, wood, porcelain and oil. Modern transformers use chemically treated paper to improve its tensile strength and resistance to aging caused by immersion in oil. But these insulation papers are mainly aged by thermal stress. Over the life time of the insulation paper and oil, it is exposed to high temperatures, oxygen and water. Its interaction with the steel of the tank and core plus the copper and aluminium of the windings will eventually cause the chemical properties of the oil to decay. High temperature have an effect on mechanical strength of cellulous paper used in the layer insulation. We made two aging cells in which insulation papers and mineral oil are conducted to test thermal properties. It is measured dielectric strength, number of acid, moisture, etc. of insulation paper and oil aged in the aging cells.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.34-37
• /
• 2001

In this study, the capacitance-voltage properties of (Sr$_{1-x}$ .Ca$_{x}$)TiO$_3$(0.05$\leq$x$\leq$0.20)-based grain boundary layer ceramics were investigated. The ceramics were fabricated by the conventional mixed oxide method. The sintering temperature and time were 1480~150$0^{\circ}C$ and 4 hours, respectively. The 2nd phase formed by the thermal diffusion of CuO from the surface leads to very excellent dielectric properties, that is, $\varepsilon$$_{r}$>50000, tan$\delta$<0.05, $\Delta$C<$\pm$10%. The capacitance is almost unchanged below about 20[V] but it decreases slowly about 20[V]. The results of the capacitance-voltage properties indicated that the grain boundary was composed of the continuous insulating layers.ulating layers.s.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.130-131
• /
• 2019

As part of recent low-energy policies, thermal insulation standards for buildings are being tightened every year. In addition, the conventional styrofoam insulating material has a problem that the thickness of the heat insulating material to achieve a standard heat permeability is rapidly increased. Due to the thick insulation, there is a high risk of spreading vulnerable structures such as fire due to lack of space between buildings. On the other hand, the method of using the insulation as a formwork is known to be excellent cost saving effect through the reduction of the formwork usage and the simplification of the external insulation work. In order to solve this problem, this study aims to fabricate a multi-layered insulator that combines high-performance phenolic foam insulation and styrofoam insulation and evaluate the deflection characteristics for use as formwork.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.96-97
• /
• 2013

Research and analysis on thermal insulation status of existing buildings are needed to make data for repair and rehabilitation caused by deterioration in insulating material performance. To do this, we have researched and analyzed the insulation status of existing buildings according to the balcony with measuring instruments in pre-set investigation conditions.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.226-227
• /
• 2015

This research is to measure and analyze the thermal performance of the apartment structure and to evaluate and establish standards of thermal insulation defect in order to make the basic data necessary for determining the degree of the thermal performance degradation and for repairing and reinforcing the exterior wall of the existing apartment. The following conclusions could be derived thorough the investigation of outer wall temperature distribution and the insulation assesment experiments using a model of specimens for the apartment houses' outer walls. It was confirmed that for the thermal performance through the insulating material thicknesses 5cm, 8cm in walls, the thermal insulation thickened by 3cm, from 5cm to 8cm, but that the actual temperature difference reached only about 1 ~ 2℃. This implies that the thermal performance improvement using the thermal insulation in walls is not significant and that it is difficult to insulate the thermal bridge area.