• Korean journal of applied entomology
• /
• v.2
• /
• pp.12-15
• /
• 1963

1. The trials were planned to test seven different fungicides for the control of Early blight of potato during the period of 1962 and 1963. 2. All of fungicides tested in the trials were considerably effective to control the disease, as the result of 4 applications which was done in one week intervals from early of June in 1963. All treatments were effective enough to make significant differences from the untreated. Especially, Dithyane M45, Difolatan and Dithane M22 showed satisfactory control even though no significant differences were obtained among them. Besides the three treatments, Bordeaux Mixture were relatively effective.

• Structural Engineering and Mechanics
• /
• v.57 no.2
• /
• pp.357-367
• /
• 2016

This paper illustrates an experimental study on a self compacting polymer concrete called isobeton made of polyurethane foam and expanded clay. Several experiments were conducted to characterize the physic-mechanical properties of the considered material. Application of the Linear Elastic Fracture Mechanics (LEFM) and determining the toughness of two isobetons based on Belgian and Italian clay, was conducted to determine the stress intensity factor $K_{IC}$ and the rate of releasing energy $G_{IC}$. The material considered was tested under static and dynamic loadings for two different samples with $10{\times}10{\times}40$ and $10{\times}15{\times}40cm$ dimensions. The result obtained by the application of the Linear Elastic Fracture Mechanics (LEFM) shows that is optimistic and fulfilled the physic-mechanical requirement of the study.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.4
• /
• pp.113-120
• /
• 2014

To ventilate indoor spaces, axial single-blade fans are widely used in various areas, such as schools, houses, offices, and restaurants. Recently, axial single-blade fans were developed to realize energy efficiency and noise reduction improvements. Here, an experimental study of the air flow characteristics of an axial dual-blade fan is conducted. The characteristics of the axial dual-blade fan were tested via an air flow analysis and with prototypes. For the performance of the fan, the flow rate, power consumption, and noise were evaluated. The result showed that the axial dual-blade fan uses less power and produces less noise in comparison with an axial single-blade fan.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.1
• /
• pp.9-16
• /
• 2008

It is important not only to reduce the casting defects of piston but also to improvement in the mechanical properties(hardness) of piston for the air compressor. The blow hole is typical casting defects in the conventional cast of aluminium alloy(AC8A-T6) piston. Because of the heat treatment method, mechanical properties of the aluminium alloy for piston was decided on the heat treatment method and cycle. Therefore, we tested on the development of mechanical properties and on the casting defects of piston for the air compressor in accordance with the heat treatment and casting condition. After the heat treatment and casting was carried out as several times, and was compared with the imported piston. As a result of several investigations; microstructure, hardness and casting defects of piston was changed under the influence of the heat treatment and casting method. When the cooling rate was controlled and the uni-cast method used, it bas the same mechanical properties and microstructure.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.5
• /
• pp.31-38
• /
• 2001

This paper deals with the micro turning property of setting angle using diamond tool. The bed of the system has used the granite which has the thermal and vibrational characteristics superior to the cast iron bed for the common machine tool. To minimize the inner and outer vibration of the fuming system, an air pad system was manufactured and tested. The aero-static spindle system which has the excellent rotation accuracy was designed and manufactured. As a result of the micro-cutting test on aluminum alloy, tool setting angel have effected on surface roughness. From the results, the micro-cutting conditions hope to provide the useful actual data using in industrial fields.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.6
• /
• pp.576-584
• /
• 2009

Up to now, it has been said that no satisfactory computer solution has been found for synthesizing four-bar linkage based on the prescribed coupler link curve. In our study, an algorithm has been developed to improve the design synthesis of four bar linkage based on the 5 precision points method. The suggested algorithm generates the desired coupler curve by using NURBS, and then the generated curve approximates as closely as possible to the desired curve representing coupler link trajectory. Also, when comparing each generated curve by constructing the control polygon, rapid comparison is easily achieved by applying convex hull of the control polygon. Finally, an optimization process using ADS is incorporated into the algorithm based on the 5 precision point method to reduce the total optimization process time. As for examples, two four bar linkages were tested and the result well demonstrated the effectiveness of the algorithm.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.5
• /
• pp.327-334
• /
• 2008

Effects of tube inclination on pool boiling heat transfer have been studied for the saturated water at atmospheric pressure. For the analysis, seven inclination angles varying from the horizontal to the vertical and two tube diameters(25.4 and 30.0 mm) are tested. According to the results, inclination angles result in much change on heat transfer. For the same wall superheat(about $5.3^{\circ}C$) the ratio between two heat fluxes for the $45^{\circ}$ inclined and the vertical has the value of more than five when the tube diameter is 25.4mm. As the inclination angle is increasing from the horizontal to the vertical direction heat transfer is gradually increasing because of the increase in liquid agitation. However the detailed tendency depends on the ratio between the tube length and the diameter.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.8
• /
• pp.582-588
• /
• 2008

An experimental investigation was conducted to investigate the effect of Bio-ethanol fuel on the engine performance and exhaust emission characteristics under various engine operating conditions. To investigate the effect of bio-ethanol fuel, the commercial 1.6L SI engine equipped with 4 cylinder was tested on EC dynamometer. The engine performance including brake torque, brake specific fuel consumption, and barke specific energy consumption of bio-ethanol fuel was compared to those obtained by pure gasoline. Furthermore, the exhaust emissions were analyzed in terms of regulated exhaust emissions such as unburned hydrocarbon, oxides of nitrogen, and carbon monoxide.Result of this work shows that the effect of blending of ethanol to gasoline caused drastic decrease of emissions under various operating conditions. Also, improved engine performance such as brake torque and brake power were indicated for bio-ethanol fuel.

• Journal of the Korea Society of Computer and Information
• /
• v.21 no.12
• /
• pp.125-130
• /
• 2016

Automatic quality inspection by computer vision can be applied and give a solution to the pharmaceutical industry field. Pharmaceutical capsule can be easily affected by flaws like dents, cracks, holes, etc. In order to solve the quality inspection problem, it is required computationally efficient image processing technique like thresholding, boundary edge detection and segmentation and some automated systems are available but they are very expensive to use. In this paper, we have developed a dented capsule image processing technique using edge-based image segmentation, TLS(Total Least Squares) curve fitting technique and adopted low cost camera module for capsule image capturing. We have tested and evaluated the accuracy, training and testing time of the classification recognition algorithms like PCA(Principal Component Analysis), ICA(Independent Component Analysis) and SVM(Support Vector Machine) to show the performance. With the result, PCA, ICA has low accuracy, but SVM has good accuracy to use for classifying the dented capsule.

• Journal of the Korea Society of Computer and Information
• /
• v.22 no.11
• /
• pp.31-37
• /
• 2017

In this paper, we propose efficient design and construction of an infrared wide angle optical system with low distortion utilizing a high resolution detector for automobile application. The operational convenience and the recognition ability have been improved significantly by applying the high resolution uncooled thermal detector with wide angle optical design. The active ahtermalization mechanism is implemented so that the adjustment of the optical component of the system is to be made automatically according to the temperature change by motorized control. The modulation transfer function (MTF) is about 50% at the Nyquist frequency close the diffraction limit. The distortion is less than 5% at the edge field. As a result, a high-resolution uncooled thermal optical system with wide field of view (FOV) is assembled, aligned and its performance is tested successfully.