• 한국환경보건학회지
• /
• 제22권1호
• /
• pp.82-90
• /
• 1996

The objectives of this study were to examine the start-up method and characteristics of biomass attachment on the media in an anaerobic fluidized bed reactor(AFBR). The media adopted was the granular activated carbon which was successfully capable of adsorbing organics and biomass. The reactor was operated at 5 kg $COD/m^3\cdot day$ and 24hr of HRT. There were important problems in the AFBR's start-up, which has been reported very long and unstable. Therefore, this research was to solve the problem of the start-up and it was performed, comparing two start-up ways that were initial fluidized system and initial static-fluidized system. The results were summarized as follows: (1) On the whole initial static-fluidized system was superior to initial fluidized system in the aspects of biogas production rate, methane content and COD removal efficiency etc. (2) At the steady state methane production rate and recoverable bioenergy of initial static-fluidized system were $2.074 m^3CH_4/m^3\cdot day$, $0.488 m^3CH_4/kgCOD_{removed}\cdot day$, and 81.3kcal/day, respectively. (3) Thickness of biofilm was about $5.11 \mu m$, $\rho_{bw}$ and $\rho_{bd}$ were $1.022 g/cm^3, 0.0953g/cm^3$ respectively. (4) Biomass concentration of fluidized state was about 35 mg/g GAC. In conclusion the efficient method on the start-up of the AFBR using GAC as media was initial static-fluidized system and the period of static state needed to reach steady state was considered about twenty days.

• Design & Manufacturing
• /
• 제7권1호
• /
• pp.55-59
• /
• 2013

A Light Emitting Diode(LED) is a semiconductor device which converts electricity into light. LEDs are widely used in a field of illumination, LCD(Liquid Crystal Display) backlight, mobile signals because they have several merits, such as low power consumption, long lifetime, high brightness, fast response, environment friendly. In general, LEDs production does die bonding and wire bonding on board, and do silicon and phosphor dispensing to protect LED chip and improve brightness. Then lens molding process is performed using mixed liquid silicon rubber(LSR) by resin and hardener. A mixture of resin and hardener affect the optical characteristics of the LED lens. In this paper, computational design of static mixer was performed for mixing of liquid silicon. To evaluate characteristic of mixing efficiency, finite element model of static mixer was generated, and fluidic analysis was performed according to length of mixing element. Finally, optimal condition of length of mixing element was applied to static mixer from result of fluidic analysis.

• 한국지반환경공학회 논문집
• /
• 제10권3호
• /
• pp.5-12
• /
• 2009

본 연구는 발전소의 적치장에서 채취한 석탄회의 정적 및 동적 강도를 제시하였다. 석탄회는 주로 저회로 이루어져 있으며 정적 및 동적 강도를 평가하기 위하여 NGI형 단순전단시험, 반복단순전단시험 및 직접전단시험을 수행하였으며, 이러한 시험으로부터의 강도를 모래의 강도와 비교하였다. 본 연구에 사용된 석탄회 속에 있는 저회는 입도분포에 의하면 모래로 분류되었으며 모래보다 높은 강도 특성을 보였다. 석탄회를 토목공사에 활용되기 위해서 사질토와 석탄회를 50:50의 비율로 배치플랜트에서 섞어 사용하는 것은 사질토층과 석탄회층을 교대로 층별 시공하는 것보다 비효율적이다. 혼합시공과 층별시공을 모사하기 위하여 모래와 석탄회가 50:50으로 조성된 시료를 준비하였다. 시험결과 혼합에 의한 시료가 층별시료보다 약간 큰 정적 및 동적 강도를 나타내었다. 높은 강도는 주로 저회의 모난 입자로부터 기인된 것으로 보인다. 혼합시료에서 액상화시의 반복응력비는 반복횟수가 증가함에 따라 층별시료보다 급격히 감소하였다.

• 한국항공우주학회지
• /
• 제40권8호
• /
• pp.711-717
• /
• 2012

스포츠급 경항공기 개념 설계 단계에서 항공기의 정적 안정성 분석을 위해 1/5 축소모델로 풍동시험을 수행하였다. 제안된 경항공기의 동체 단독 및 동체에 주익, 수평꼬리날개, 수직꼬리날개 등을 조합한 6개 형상에 작용하는 공력을 내장형 밸런스를 이용하여 측정하고 정안정 미계수를 도출하여 기본 양항력 공력특성 및 각 요소가 세로 방향 가로 정안정 특성에 미치는 효과를 분석하였다. 풍동시험 결과로부터 특히, 수평꼬리날개와 수직꼬리날개 그리고 고익형태와 상반각을 갖는 주익 등이 각각 세로, 방향, 가로 정안정성에 미치는 기여정도를 정량적으로 파악하였으며, 본 시험결과는 항공기 각 형상 구성품 조합의 정안정 특성에 관한 유용한 실험자료로 활용될 수 있을 것이다.

• Geomechanics and Engineering
• /
• 제29권2호
• /
• pp.99-111
• /
• 2022

Instability of bolted rock mass has been a major hazard in the underground coal mining industry for decades. Developing effective support guidelines requires understanding of complex bolted rock mass failure mechanisms. In this study, the dynamic failure behavior, mechanical behavior, and energy evolution of a laboratory-scale bolted specimens is studied by conducting laboratory static-dynamic coupled loading tests. The results showed that: (1) Under static-dynamic coupled loading, the stress-strain curve of the bolted rock mass has a significant impact velocity (strain rate) correlation, and the stress-strain curve shows rebound characteristics after the peak; (2) There is a critical strain rate in a rock mass under static-dynamic coupled loading, and it decreases exponentially with increasing pre-static load level. Bolting can significantly improve the critical strain rate of a rock mass; (3) Compared with a no-bolt rock mass, the dissipation energy ratio of the bolted rock mass decreases exponentially with increasing pre-static load level, the ultimate dynamic impact energy and dissipation energy of the bolted rock mass increase significantly, and the increasing index of the ratio of dissipation energy increases linearly with the pre-static load; (4) Based on laboratory testing and on-site microseismic and stress monitoring, a design method is proposed for a roadway bolt support against dynamic load disturbance, which provides guidance for the design of deep underground roadway anchorage supports. The research results provide new ideas for explaining the failure behavior of anchorage supports and adopting reasonable design and construction practices.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.213-215
• /
• 1996

Until now the test of LIM have been mainly experimented for a small capacity LIM. This paper deals with the static characteristics of a large capacity LIM which is designed for MAGLEV. And we developed the simulation program using electro-magnetic field theory and equivalent circuit method. Hence it is evaluated the performance of a large capacity LIM. Also this paper predicts the dynamic characteristics of LIM with the proposed simulation program.

• 한국정보통신학회논문지
• /
• 제6권3호
• /
• pp.421-426
• /
• 2002

Hybrid cascade multilevel PWM inverter has advantages of hybrid structure which enhances the better utilization of power semiconductor switches, that is, both hi호 power-low frequency switch, GTO and low power-high frequency switch, IGBT can be used in the same circuit. In this paper, a static var compensator using hybrid cascade 5-level PWM inverter is presented for high voltage/high power applications. The proposed system is modelled by circuit DQ transformation, and thus an equivalent circuit is obtained which reveals the important characteristics of the system and lead to the related equations. Finally, circuit structure and characteristics is presented and the validity of the characteristics analysis is shown through PSIM simulation.

• 한국정밀공학회지
• /
• 제17권3호
• /
• pp.192-199
• /
• 2000

The spot-welded automotive side member which has a hat-shaped section and a double hat shaped section has been tested on the axial static(10mm/min) and quasi-static(50mm/min) compressing load. The collapse characteristics of automotive sections have been reviews on shift on shape and in width of the spot-voiding on the flange. On the basis of the results of tests and reviews, the optimum energy absorption capacity of the structure has been studied.

• Tribology and Lubricants
• /
• 제6권2호
• /
• pp.76-87
• /
• 1990

It is known that the effects of oil supply conditions on the characteristics of plain journal bearings are significant and especially the dynamic characteristics are affected by cavity region. For various shapes (axial groove, spiral groove, X-shape groove) and positions of oil grooves, the pressure distribution and the static performance of plain journal bearings are obtained with numerical methods. Elrods algorithm which implements JFO oil rupture/reformation boundary condition is used in order to take into account the effect of cavity region. It is shown that in the cases of axial groove or X-shape groove the load capacity and the attitude angle are affected by the groove position but the effect of spiral groove position is less significant.

• 대한전자공학회논문지SD
• /
• 제41권7호
• /
• pp.37-41
• /
• 2004

We have formulated an empirical analytic model for the static characteristics of implanted vertical-cavity surface-emitting lasers (VCSELs). Specifically, we have derived analytic formulas for the threshold current, slope efficiency, dynamic resistance, and the output power and forward voltage at the operation current of 12 ㎃ in terms of the implant and metal-aperture radii by fitting the measured results. The radii of the metal aperture and implant mask of the 850 nm VCSELs range from 4 to 12.5 ${\mu}{\textrm}{m}$ and 7 to 17.5 ${\mu}{\textrm}{m}$ respectively. The model shows the way of tailoring the VCSEL characteristics by changing the mask dimensions only.