• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.12
• /
• pp.3235-3245
• /
• 1996

A DDFS(Direct Digital Frequency Synthesizer) used in spread spectrum communication systems must need fast switching speed, high resolution(the step size of the synthesizer), small size and low power. The chip has been designed with four parallel sine look-up table to achieve four times throughput of a single DDFS. To achieve a high processing speed DDFS chip, a 24-bit pipelined CMOS technique has been applied to the phase accumulator design. To reduce the size of the ROM, each sine ROM of the DDFS is stored 0-.pi./2 sine wave data by taking advantage of the fact that only one quadrant of the sine needs to be stored, since the sine the sine has symmetric property. And the 8 bit of phase accumulator's output are used as ROM addresses, and the 2 MSBs control the quadrants to synthesis the sine wave. To compensate the spectrum purity ty phase truncation, the DDFS use a noise shaper that structure like a phase accumlator. The system input clock is divided clock, 1/2*clock, and 1/4*clock. and the system use a low frequency(1/4*clock) except MUX block, so reduce the power consumption. A 107MHz DDFS(Direct Digital Frequency Synthesizer) implemented using 0.8.mu.m CMOS gate array technologies is presented. The synthesizer covers a bandwidth from DC to 26.5MHz in steps of 1.48Hz with a switching speed of 0.5.mu.s and a turing latency of 55 clock cycles. The DDFS synthesizes 10 bit sine waveforms with a spectral purity of -65dBc. Power consumption is 276.5mW at 40MHz and 5V.

• Journal of Biosystems Engineering
• /
• v.39 no.2
• /
• pp.87-95
• /
• 2014

Purpose: The purpose of this study was to design a variable frequency LED light system for plant factory which combined red, blue, green, white, and UV lights and controlled the ratio of the light wavelength. In addition, this study evaluated the performance of each combination of LED to verify the applicability. Methods: Four combinations of LED (i.e. Red+Blue, Red+Blue+Green, Red+Blue+White, Red+Blue+UV) were designed using five types of LED. The system was designed to control the duty ratio of each wavelength of LED by 1% interval from 0~100%, the pulse by 1Hz interval from 1~20kHz. Response characteristics of the control system, spectral distribution of each combination, light uniformity and uniformity ratio were measured to test the performance of the system. Results: Clean waveforms were measured from 10Hz to 10kHz regardless of duty ratio. Frequency distortion was observed within 5% of inflection point at frequencies above 10kHz regardless of duty ratio, but it was judged negligible. Spectra showed a normal distribution, and maximum PPF with duty ratio of 100% was $271.4{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ for the Red+Blue combination. PPF of the Red+Blue+Green combination was $258.9{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, and that of the Red+Blue+White combination was $273.9{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$. PPF of the Red+Blue+UV combination was $267.7{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$. Uniformity ratio for the area excepting border showed 0.90 for the Red+Blue and Red+Blue+White combinations, 0.87 for the Red+Blue+Green combination, and 0.88 for the Red+Blue+UV combination. The light was irradiated evenly at the area excepting border, so it was suitable for plant growing. Conclusions: From the results of this study, response characteristics of the control system, spectral distribution of each combination, light uniformity and uniformity ratio were suitable for applying into the plant factory.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.120-127
• /
• 2005

The design method of the transversal filter using continuously cascaded directional couplers is presented. The coupler can be treated for a continuously varying nonuniform coupled transmission line. The design method is based on the optimum extraction of desired coupling factor by the control of null positions which are inherent to the coupling spectra pattern. In the optimization process, the improved Woodward-Lawson sampling method is applied to easily synthesize the distributed delay and weighting elements for transversal filter properties. For application, the microstrip transversal filter is fabricated and optimum dielectric overlay is introduced for the mode phase velocity compensation for non-TEM coupler nodes by using SDA(Spectral Domain Approach). Experiment results confirm the validity of the proposed method.

• International Journal of Human Ecology
• /
• v.7 no.2
• /
• pp.43-52
• /
• 2006

This study analyzed and compared the color characteristics of preferred textiles for blouses and shirts of college students. After the survey of preference in fabrics for blouses and shirts of college students according to season, colors of preferred fabrics were analyzed. Spectral data were measured and a chromaticity diagram was drawn. The color of shirt fabric that college students preferred in the spring/fall was PB (Purple-Blue) and light shades, and in summer, PB color and pale shades. Generally achromatic black or a simple color that is close to an achromatic color, light and soft shades were preferred. For blouse fabric, PB, d (dull) and g (grayish) tones were preferred in spring/fall, G (Green) and It., d. were preferred in summer. Achromatic white and medium, soft shaded chromatic especially greenish colors were preferred. In spring fall, regardless of the clothing item, PB was the most preferred color. Y (Yellow) was the most preferred color for shirts, and for blouses, R (Red) was the most preferred. For achromatic color, black is preferred for shirts, white is preferred for blouses. In summer, the color of preferred shirt fabric was PB, and blouse fabric had a lot of G color. College students prefer simple colors which are close to achromatic colors, and light and soft color were preferred for shirt fabric and they preferred various, medium shaded and closer to pure colors for blouses because college students tend to consider the aesthetic side as important and usually wear blouses less often than shirts.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.5
• /
• pp.243-250
• /
• 2002

In the synthesis of the current source distribution function of an array antenna with the arbitrary radiation pattern, the Woodward-Lawson sampling method has been mainly used for the synthesis of an even function lobe pattern. In this paper, the method is extended to the synthesis of the odd function pattern and then the optimum synthesis method for the nonlinear source distribution function is proposed. The proposed method is applied to the design of nonuniform transmission lines with arbitrary reflection responses. The both dispersive impedance profiles of single and coupled nonuniform lines with arbitrary reflection responses are directly synthesized by the sampled values of a reflected spectral pattern which is optimally shaped by a perturbation of its complex null positions, hence removing the conventional step-by-step segmentation process and global optimization routines. The control problem in the case that all of port impedances are identical is also solved. The generality of the proposed method is verified by a filter design with the controlled arbitrary passband

• Journal of IKEEE
• /
• v.7 no.1 s.12
• /
• pp.72-79
• /
• 2003

Classical designs of optical transimpedance preamplifier for p-i-n photodiode receiver circuits generally employ common source transimpedance input stages. In this paper, we explore the design of a class of current-mode optical transimpedance preamplifier based upon common gate input stages. A feature of current-mode optical transimpedance preamplifier is high gain and high bandwidth. The bandwidth of the transimpedance preamplifier can also be increased by the capacitive peaking technique. In this paper we included the development and application of a circuit analysis technique based on the minimum noise. We develop a general formulation of the technique, illustrate its use on a number of circuit examples, and apply it to the design and optimization of the low-noise transimpedance amplifier. Using the noise minimization method and the capacitive peaking technique we designed a transimpedance preamplifier with low noise, high-speed current-mode transimpedance preamplifier with a 1.57GHz bandwidth, and a 2.34K transimpedance gain, a 470nA input noise current. The proposed preamplifier consumes 16.84mW from a 3.3V power supply.

• Smart Structures and Systems
• /
• v.19 no.5
• /
• pp.487-497
• /
• 2017

Semi-active devices use the building's own motion to produce resistive forces and are thus strictly dissipative and require little power. Devices that independently control the binary open/closed valve state can enable novel device hysteresis loops that were not previously possible. However, some device hysteresis loops cannot be obtained without active analog valve control allowing slower, controlled release of stored energy, and is presents an ongoing limitation in obtaining the full range of possibilities offered by these devices. This in silico study develops a proportional-derivative feedback control law using a validated nonlinear device model to track an ideal diamond-shaped force-displacement response profile using active analog valve control. It is validated by comparison to the ideal shape for both sinusoidal and random seismic input motions. Structural application specific spectral analysis compares the performance for the non-linear, actively controlled case to those obtained with an ideal, linear model to validate that the potential performance will be retained when considering realistic nonlinear behaviour and the designed valve control approach. Results show tracking of the device force-displacement loop to within 3-5% of the desired ideal curve. Valve delay, rather than control law design, is the primary limiting factor, and analysis indicates a ratio of valve delay to structural period must be 1/10 or smaller to ensure adequate tracking, relating valve performance to structural period and overall device performance under control. Overall, the results show that active analog feedback control of energy release in these devices can significantly increase the range of resetable, valve-controlled semi-active device performance and hysteresis loops, in turn increasing their performance envelop and application space.

• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.130-133
• /
• 2007

In order to get high quality and high resolution image data from the space-borne camera system, the image chain from the sensor to the user in the ground-station need to be designed and controlled with extreme care. The behavior of the camera system needs to be controlled by ground commands to support on-orbit calibration and to adjust imaging parameters and to perform early stage on-orbit image correction, like gain and offset control, non-uniformity correction, etc. The operation status including the temperature of the sensor needs to be transferred to the ground-station. The preparation time of the camera system for imaging with specific parameters should be minimized. The camera controller needs to synchronize the operation of cameras for every channel and for every spectral band. Detail timing information of the image data needs to be provided for image data correction at ground-station. In this paper, the design of the camera controller for the AEISS on KOMPSAT-3 will be introduced. It will be described how the image chain is controlled and which imaging parameters are to be adjusted The camera controller will have software for the flexible operation of the camera by the ground-station operators and it can be reconfigured by ground commands. A simple concept of the camera operations and the design of the camera controller, not only with hardware but also with controller software are to be introduced in this paper.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.2
• /
• pp.153.2-153.2
• /
• 2011

The IGRINS (Immersion GRating INfrared Spectrometer) is a high resolution wide-band infrared spectrograph developed by Korea Astronomy and Space Science Institute (KASI) and the University of Texas at Austin (UT). Immersion grating is a key component of IGRINS, which disperses the input ray by using a Silicon material with a lithography technology. Opto-mechanical mount for the immersion grating is important to keep the high spectral resolution and the optical alignment in a cold temperature of $130{\pm}0.06K$. The optical performance of immersion grating can maintain within the de-center tolerance of ${\pm}0.05mm$ and the tip-tilt tolerance of ${\pm}1.5arcmin$. The mount mechanism utilizes the flexure and the kinematic support design to satisfy the requirement and the operation condition. When the IGRINS system is cooled down to a cold temperature, three flexures compensate the thermal contraction stress due to the different material between the immersion grating and the mounting part(Aluminum 6061). They also support the immersion grating by an appropriate preload. Thermal stability is controlled by a copper strap with proper dimensions and a heater. Generally structural and thermal analysis was performed to confirm the mount mechanism. This talk presents the opto-mechanical mount design of the immersion grating of IGRINS.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.3
• /
• pp.58-63
• /
• 2007

GPS signal is vulnerable to intentional and unintentional interferences since it has a very weak signal power and its structure is well-known. Among the interference rejecting techniques, the ATF is being generally used as a pre-correlation technique. However, it does not have a design parameter relating to the notch width, resulting in the spectral loss around frequency of the interference. The IIR notch filter has a design parameter relating to the notch width and can generate a sharp notch for the CW interference. In this paper, an adaptive IIR notch filter is proposed and the performance is evaluated using software signal generator and real measurements.