• The Journal of Engineering Geology
• /
• v.17 no.3
• /
• pp.425-434
• /
• 2007

In this paper, the stability standards of slopes reclaimed by soils mixed with stone dust were proposed to manage the stone dust as recovery soils. First of all, the mixed ratio between stone dust and natural soil is classified into 5 groups, and a series of soil test was performed in each group. As the results of tests, the shear strength and the maximum dry unit weight were increased in decrease of the mixed ratio of stone dust. On the basis of the investigation to the safety factor standards of embankment slopes in and outside the country, a slope stability rank of slopes reclaimed by mixed soils were divided into 3 stages such as unstable stage, attention stage and stable stage. The slope angle, the slope height and the mixed ratio with stone dust were proposed by the result of stability analysis of slopes reclaimed by mixed soils. As the result of slope stability analysis, the slope angle of 1 : 1.8 at the reclaimed slope should be constructed in case of the slope height of 10 m. Also, the slope angle of 1 : 1.8 and the mixed ratio of stone dust less than 50% should be constructed in case of the slope height of 15 m. The analysis result of reclaimed slope constructed inside the quarry is similar to that of reclaimed slope constructed on the open ground in same conditions of the slope angle, the slope height and the mixed ratio with stone dust. The proposed stability standards of slopes reclaimed by soils mixed with stone dust can be used practically at the quarrying site.

• The Journal of Engineering Geology
• /
• v.25 no.1
• /
• pp.57-66
• /
• 2015

A numerical analysis was performed of the seepage from and stability of a mine waste-dump slope in Imgi, Busan, considering rainfall intensity. The 40-45° slope angle of the waste dump is relatively steep, and the depth of the waste dump down to bedrock is 7-8 m. The groundwater level was 6.6 m below the surface. Various laboratory tests on samples obtained from the waste dump were performed to determine the input data for seepage and stability analyses of the waste-dump slope during rainfall. The results of seepage analysis for various rainfall intensities using the SEEP/W program show that the wetting front moved down with increasing rainfall duration. When the rainfall intensity was > 50 mm/ hour and the duration was > 24 hours, the waste dump became fully saturated because the wetting front reached the groundwater level. The results of slope stability analysis coupled with seepage analysis using the SLOPE/W program show that the safety factor of the slope decreased as the wetting front moved down due to rainfall infiltration. After continuous rainfall for 5-6 hours, the safety factor of the slope suddenly decreased but then recovered and converged. The sudden decrease was induced by an increase in pore-water pressure and a decrease in matric suction down to a certain depth as the wetting front approached the potential sliding surface.

• The Journal of Engineering Geology
• /
• v.20 no.2
• /
• pp.155-167
• /
• 2010

In analysis of slope stability, deterministic analysis which yields a factor of safety has been used until recently. However, probability of failure is considered as a more efficient method because it deals with the uncertainty and variability of rock mass. In both methods, a factor of safety or a probability of failure is calculated for a slope although characteristics of rock mass, such as characteristics of joints, weathering degree of rock and so on, are not uniform throughout the slope. In this paper, we divided a model slope into several zones depending on conditions of rock mass and joints, and probabilities of failure in each zone are calculated and compared with that calculated in whole slope. The persistence of joint was also used as a parameter in calculation of probability of failure. A rock slope located in Hongcheon, Gangwondo was selected and the probability of failure using zoning and persistence as parameter was calculated to confirm the applicability of model analysis.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.3
• /
• pp.1017-1025
• /
• 2013

The monolithically coupled finite element analysis for a deformable unsaturated soil slope is performed to investigate matric suction distribution on a soil slope subjected to rainfall infiltration, which can consider the hydraulic-mechanical characteristics for the analysis. The soil-water characteristic curves (SWCC) are experimentally determined to estimate three types of hydraulic properties of domestic areas. Based on the physical properties, the distribution of matric suction is investigated by considering the major factors, such as soil conditions, rainfall intensities, and slope angles. It is found from the results of this study that the matric suction rapidly decreases with an increase in rainfall intensity, regardless a slope angle. The slope surface is more easily saturated when its saturated hydraulic conductivity is smaller than rainfall intensity, and for the case of multi-layered soil slope, hydraulic characteristics of slope surface has a significant influence on matric suction distribution.

• Tunnel and Underground Space
• /
• v.28 no.6
• /
• pp.569-583
• /
• 2018

The purpose of this study is to identify the collapse characteristics by analyzing various factors causing collapse based on field survey and existing data on rock slopes occurring in the construction of roads and industrial complexes in Gyeongsangnam - do area. In the case of the slope where the slope has been directly surveyed, the analysis of the collapse characteristics can be used for the prediction and prevention of slope failure through the continuous collection of the slope data, database construction, management and analysis. The evaluation items used in the collapse characteristics of slope were selected among the items that can be regarded as objective evaluation items among the overlapping factors by comparing the evaluation items frequently used for the evaluation of the existing slope stability among various factors. The type of destruction of the rock slope depends on the type of carcass of the bedrock, such as planar fracture, wedge fracture, onho fracture, and conduction fracture, which are different from each other. And the slope stability analysis should be performed accordingly.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.1302-1308
• /
• 2010

This study the change of the safety factor before and after the reinforcement were compared by performing the parameter research based on the limit equilibrium analysis regarding the same cross section after carrying out the safety factor before the reinforcement on the virtual section in order to observe the change of the safety factor of the slop reinforced with the slope planting reinforced earth, and the variation of the safety factor according to the increase of the length of the reinforcement materials and the change of the slope height was analyzed. As the result, the reinforcement effect was insignificant at no more than 0.6 of L/H, the reinforcement length ratio when the reinforcement length was increased, as the increase of the safety factor was slow comparing with the non-reinforced slope. At 3.0m of the slope height, reinforcement on the slope is not necessary, and at 3.0m to 5.0m of the slope height, the inclination was not influencing at no less than 0.6 of L/H. At 5.0m to 9.0m of the slope height, the safety factor was mostly secured on the slope at 0.8 of L/H and the over-reinforced slope appeared at no less than 1.0 of L/H. Also, the safety factor increased as the slope height increases and the slope gets steeper till 0.8 of L/H, but the slope steepness affects more on the increase of the safety factor than the reinforcement material, as the reinforcing force by the reinforcement material became steady.

• Geomechanics and Engineering
• /
• v.31 no.5
• /
• pp.439-452
• /
• 2022

A forecast of slope behavior during catastrophic events, such as earthquakes is crucial to recognize the risk of slope failure. This paper endeavors to eliminate the significant supposition of predefined slip surfaces in the slope stability analysis, which questions the relevance of simple conventional methods under seismic conditions. To overcome such limitations, a methodology dependent on the slip line hypothesis, which permits an automatic generation of slip surfaces, is embraced to trace the extreme slope face under static and seismic conditions. The effect of earthquakes is considered using the pseudo-static approach. The current outcomes developed from a parametric study endorse a non-linear slope surface as the extreme profile, which is in accordance with the geomorphological aspect of slopes. The proposed methodology is compared with the finite element limit analysis to ensure credibility. Through the design charts obtained from the current investigation, the stability of slopes can be assessed under seismic conditions. It can be observed that the extreme slope profile demands a flat configuration to endure the condition of the limiting equilibrium at a higher level of seismicity. However, a concurrent enhancement in the shear strength of the slope medium suppresses this tendency by offering greater resistance to the seismic inertial forces induced in the medium. Unlike the traditional linear slopes, the extreme slope profiles mostly exhibit a steeper layout over a significant part of the slope height, thus ensuring a more optimized solution to the slope stability problem. Further, the susceptibility of the Longnan slope failure in the Huining-Wudu seismic belt is predicted using the current plasticity approach, which is found to be in close agreement with a case study reported in the literature. Finally, the concept of equivalent single or multi-tiered planar slopes is explored through an example problem, which exhibits the appropriateness of the proposed non-linear slope geometry under actual field conditions.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.6
• /
• pp.172-182
• /
• 2003

In this study, the back analysis was performed by means of stereo-net, plane failure and block failure method to collapsed fields among the rock slopes designed by standardized criterion, and the internal frictions from the back analysis were compared with those used to reinforcement design. It was concluded that in the result of the analysis by means of stereo net, plain failure and block failure methods, the internal frictions used to re-design of collapsed slope underestimated 10$^{\circ}$, 5$^{\circ}$ and 10$^{\circ}$ in average. At present, the internal friction on the design is used the experience value according to the state of weathering, but internal friction angle by the back analysis on collapsed slope with various methods were more reliable values than those from the present method. And it was concluded that re-design was made extravagantly because the internal friction used to re-design for reinforcement of the collapsed slope was less than back analysis.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.5
• /
• pp.47-58
• /
• 2015

Triggering rainfall and geologic conditions with the state of slope hazard were investigated based on the field investigation and collected data on the slope hazard during the period between 2011 and 2014 in Korea. Analysis results showed that most of slope hazards occurred in metamorphic rock and debris flow was the most frequent type of slope hazard. Slope hazard increased when the higher monthly mean rainfall was recorded. However, most of slope hazard occurred when certain time elapsed after the moment of maximum hourly rainfall. Finally, more than one month of long-term rainfall was shown to be related to the frequency of slope hazard in the period.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.20 no.3
• /
• pp.33-43
• /
• 1992

The perceptual characteristic on the slope scenery around highway is very similar as the general perceptual characteristic in the landscape. This process determines by the relationship between the scenery observers and the characteristics of its place. It is very important to have a analysis on highway slope scenery in our particular culture in Korea since our country's highways are done by cutting mountains : therefore, we have a lot of slopes around highways. The physical characteristics on the highway scenery determines how we should build scenery around highway to a satisfactory level. The results drawn from this research work are as follow: 1) The satisfaction for slope scene had been affected by sex, native and experience of travel. I thought that the slope scene having peculiar form will offer the highest satisfaction. 2) Psychological factor, reflected satisfaction of slope scene, 몽 a grip of three factors as the factor of evaluation, texture, formation, and presumption formula is : Satisfaction=1.04(Evauluation factor)+0.83(Texture factor)+0.15(Formation factor)+4.28)R2=0.69). 3) Vine among the vegetation componeents of slope scene highly correlated with the evaluation factor and grass, shrub correlated with the texture factor. 4) Rock among the structual components of slope scene highly correlated with the formation factor, and stockade, lattice correlated with the evalution factor. 5) Gradient among the properties which determined slope form, highly correlated with the formation factor.