• Korean Journal of Metals and Materials
• /
• v.49 no.1
• /
• pp.64-72
• /
• 2011

The spot weldability of dissimilar metal joints between austenitic stainless steels (STS316)/IF steels and ferritic stainless steels (STS430)/IF steels was investigated. This study was aimed to determine the spot welding parameters for a dissimilar metal joint and to evaluate the dissimilar metal joint's weldability, including its welding nugget shape, tensile-shear strength, hardness, and microstructure. The comparison of these results was described in terms of fracture behavior. Compared with the weld lobe of similar metal joints, dissimilar metal joints (STS430/IF) had reduced weld current range. However, the weld lobe of STS316/IF steel joint showed increased weld current range. This is because the dilution of chemical composition in the molten weld pool suppressed the heat input being caused by Joule heat with current flow through the samples. The microstructure of the fusion zone was fully martensite and mixture of ferrite and martensite for austenitic stainless steel/IF steel and ferritic stainless steel/IF steel combination, respectively. The experimental results showed that the shape of nugget was asymmetric, in which the fusion zone of the austenitic and ferritic stainless steel sheet was larger due to the higher bulk-resistance. The predicted microstructure by using the Schaeffler diagram was well matched with experimental results. After peel test, the fracture was initiated from heat affected zone of ferritic stainless steel sheet side, however the final fracture was propagated into the IF steel sheet side due to its lower strength.

• Resources Recycling
• /
• v.31 no.6
• /
• pp.52-59
• /
• 2022

Calcium silicate based cement (CSC) is a low-carbon cement that emits less CO₂ by up to 70% compared to ordinary Portland cement during its manufacture. Most developed countries have commercialized CSC, whereas Korea is still investigating the manufacturing characteristics and basic properties of CSC. This paper provides a review of methods for manufacturing CSC using domestic raw materials and discusses the possibility of CSC localization based on an evaluation of the basic physical properties of manufactured CSC. The experimental results of this study indicate that the primary mineral components of CSC were CS, C₃S₂ C₂S, and unreacted SiO₂. This suggests the possibility of manufacturing CSC using domestic raw materials that exhibit mineral compositions similar to that of theoretical CSC. The compressive strength of CSC mortar is less than 1MPa at the age of 7 d under wet curing. This implies that hydration does not affect the property development of CSC mortar. Meanwhile, during carbonation curing, the compressive strength is 56 MPa or higher after 7 d, which indicates excellent early strength development. Furthermore, results of Thermogravimetric Analysis Differential scanning calorimetry (TG/DSC) show that a significant amount of CaCO₃ is formed, which is consistent with the results of previous studies. This implies that carbonation is associated significantly with the properties of CSC.

• Korean Journal of Materials Research
• /
• v.33 no.12
• /
• pp.525-529
• /
• 2023

β-Ga₂O₃ has become the focus of considerable attention as an ultra-wide bandgap semiconductor following the successful development of bulk single crystals using the melt growth method. Accordingly, homoepitaxy studies, where the interface between the substrate and the epilayer is not problematic, have become mainstream and many results have been published. However, because the cost of homo-substrates is high, research is still mainly at the laboratory level and has not yet been scaled up to commercialization. To overcome this problem, many researchers are trying to grow high quality Ga₂O₃ epilayers on hetero-substrates. We used diluted SiH4 gas to control the doping concentration during the heteroepitaxial growth of β-Ga₂O₃ on c-plane sapphire using metal organic chemical vapor deposition (MOCVD). Despite the high level of defect density inside the grown β-Ga₂O₃ epilayer due to the aggregation of random rotated domains, the carrier concentration could be controlled from 1 × 10¹⁹ to 1 × 10¹⁶ cm^-3 by diluting the SiH4 gas concentration. This study indicates that β-Ga₂O₃ hetero-epitaxy has similar potential to homo-epitaxy and is expected to accelerate the commercialization of β-Ga₂O₃ applications with the advantage of low substrate cost.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.2
• /
• pp.121-127
• /
• 2024

In this study, the applicability of replacing DG(Desulfurized Gypsum) from oil refinery with CCCMs(Carbon dioxide Conversion Capture Materials) as an ALC(Auto-claved LIghtweight Concrete) raw material was examined, and basic properties of ALC was measured. The main chemical components of DG and CCCMs were CaO and SO₃, and an increase in LOI(Loss of ignition) due to mineral carbonation reaction was verified. The crystalline phases of CCCMs were CaCO₃, CaSO₄, Ca(OH)₂, and CaSO₄·2H₂O. When DG, a raw material for ALC production, was replaced with CCCMs, foaming height, pore shape, absolute dry gravity, and compressive strength results measured similar for all binders. In addition, the formation of tobermorite which is main crystalline phase of ALC was shown for all specimens in microstructural analysis.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.3
• /
• pp.86-91
• /
• 2024

In this study, the characteristics of mortar using carbondioxide conversion capture materials (CCMs), fabricated by reacting CO₂ with desulfurization gypsum (DG) by-produced from a oil refinery, as a cement mixture. Based on the chemical component and particle size analysis results, it estimated that desulfurized gypsum reacted with carbon dioxide to produce carbonate crystals such as CaCO₃. Using CCMs as a cement mixture, physical property and durability analysis were conducted by measuring such as workability, compressive strength, compressive strength ratio after freezing-thawing and accelerated carbonation depth. The experimental results showed that as the content of the admixture increased, workability and compressive strength characteristics decreased. Compressive strength after freezing-thawing and accelerated carbonation depth also showed similar characteristics to the physical property measurement results. In addition, compared to desulfurized gypsum, using CCMs showed better physical properties and durability. This was assumed to be due to differences in the crystal phases of the mixed materials such as free-CaO and CaCO₃.

• Journal of Life Science
• /
• v.28 no.6
• /
• pp.663-670
• /
• 2018

This study was performed to confirm the antioxidative and hair-growth-promotion effects of a fermented compound composed of five materials, namely Allium cepa, Cucurbita spp., Glycine max Merr., Pinus sylvestris leaf, and Sesamum indicum. An additional compound composed of two materials was composed of Allium cepa and Cucurbita spp. Antioxidative effects were measured based on DPPH radical-scavenging activity and total flavonoid content. Fermented 5-type natural compounds (5NC) showed higher DPPH radical-scavenging activity and flavonoid content than those of fermented 2-type natural compounds (2NC). Hair-growth promotion was demonstrated in vivo. Alkaline phosphatase (ALP), oid contentontenteptidase phospactivity, and macroscopic observation were measured. Experimental animals were divided into four groups based on the samples they were administered: water, pansildil (P-CON), 5NC, and 2NC. Samples were administered orally once a day at a fixed time for four weeks. Both ALP and ${\gamma}eeksactivity$ increased in the 5NC group compared with the 2NC group. In macroscopic observation, the P-CON group grew the most and were most similar to the state before shaving. The 5NC group grew hair similar to the P-CON group. In all the results, the 5NC group showed greater antioxidative and hair-growth-promotion effects than the 2NC group. Consequently, 5NC could be used as an ingredient for hair-growth promotion.

• Journal of Bio-Environment Control
• /
• v.7 no.3
• /
• pp.259-267
• /
• 1998

This study was carried out to investigate the effect of mulching materials on the fruit quality of Miyagawa Early Satsuma Mandarin in the plastic house. The mulching time was 10 days after water irrigation breakage. The mulching materials used, in order of decreasing light reflectivity, were; micro-perforated vinyl sheets, non-woven fabric film, porous black P.E. film and non-mulching(control). Peel coloration by a values in the treatment of the micro-perforated vinyl sheets showed a 6.93 increase over the control group. The a/b values were similar to this trend, but there were no significant difference among the mulching treatment groups. The glucose level of fruit juice was much higher in the mulching treatment groups as compared with that of the control group, but there was no significant difference among the mulching treatments. Fructose content in the treatment of the micro-perforated vinyl sheets a 0.31mg%.m $L^{-1}$ increase over the control group. This group also showed a 1.36%.m $L^{-1}$ increase in sucrose and a similar increase trend in total sugar. The Brix value was 0.9 $^{\circ}$Brix higher in the micro-perforated vinyl sheet group(12.4 $^{\circ}$Brix) than in the control group(11.5 $^{\circ}$Brix) which result in a significant increase with micro-perforated vinyl sheet usage. However, the acidity level did not differ significantly among mulching treatments.

• Korean Journal of Soil Science and Fertilizer
• /
• v.36 no.1
• /
• pp.50-56
• /
• 2003

Turnover rate of applied rice straw and rice straw compost in a rice paddy soil under the flooding and intermittent irrigation was studied. The chambers in duplicate were either planted or unplanted with rice. For planted chambers, the turnover rate to methane under the flooding increased with freshness of organic materials applied: 14.9% for RS5 (rice straw applied in May), 9.5 % for RS2 (rice straw incorporated in February), and 4.0% for RSC (rice straw compost amended in May). Similar trend was found in turnover rate to methane under the intermittent irrigation: 9.8% for RS5, 5.5% for RS2, and 2.1% for RSC. For planted chambers, turnover rate to methane under the flooding was generally 1.64 times higher than that under the intermittent irrigation. In contrast, for unplanted chambers, the turnover rate to methane under the flooding increased with freshness of organic materials applied: 8.7% for RS5, 3.3% for RS2, and 3.0% for RSC. Similar trend was observed in chambers under the intermittent irrigation: 5.4% for RS5, 3.0% for RS2, and 1.4% for RSC. For unplanted chambers, the turnover rate to methane under the flooding was generally 1.52 times higher than that under the intermittent irrigation.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.1
• /
• pp.23-29
• /
• 2017

This study, to provide quantitative data related to compaction characteristics, identifies the compaction characteristics of various types of soil samplers, in relation to their particle-size distribution and plasticity degree, and the compaction characteristics of artificially created granular materials, in relation to their A & D compaction. The results of the experiments show as follows. $r_{dmax}$ of clay is less than those of both sand and gravel approximately by 10%. O.M.C of clay has turned out to be greater than sand and gravel approximately by 20% and 30%, respectively. Changes in the compaction characteristics can be observed clearly around 30~60% of sand and 30~50% of passing No.200 sieve. It has also been shown that the compaction characteristics related to LL and PL are similar to each other in changes, and that the compaction characteristics become less clear with higher percent of fine grained soil. The compaction characteristics of the artificially created granular materials and field materials have appeared almost similar to each other. $r_{dmax}$ is less approximately by 30% and O.M.C greater approximately by 20% in A compaction than in D compaction. As $r_{dmax}$ and O.M.C become greater, its rate increases.

• Journal of the Korean Society of Radiology
• /
• v.6 no.5
• /
• pp.335-342
• /
• 2012

This study aims to find a way to control infection of community radiology effectively by calculating the degree of contamination, culture and identifying the flora in radiology of five general hospitals in Gyeongsangbuk-do. Staphylococcus, Micrococcus, Pseudomonas stutzeri, Pseudomonas oryzihabitans were identified as surface flora. These are know to be pathogens of hospital acquired infection and there was no radiology-specific flora. Research subject hospitals were conducting similar infection control education but degree of contamination of each hospital showed significant difference. Difference in degree of contamination according to contact sources were analyzed by Contact sources were classified into technologist-using, patients-using and common-using materials. Analysis of each hospital's degree of contamination showed that patient-using materials were significantly more contaminated than technologist-using and common-using materials (p<0.001). Devices which are similar to each other in monthly average frequency of use showed no significant difference in degree of contamination, but general X-ray devices and chest boards which are used most frequently showed higher degree of contamination than others. In addition, hospital A, B and C which have heavier monthly average caseload showed relatively high degree of contamination on irradiation devices which are used by technologists only or by technologists and patients commonly, office desks and doorpulls. Hence it is considered that intensity of infection control education should be different according to the degree of monthly average caseload. This study provided an opportunity to aware that technologists' feeling of contamination is crucial for infection control of radiology, and the Accupoint ATP public hygiene monitoring system which was used in this study for measuring the degree of contamination was proved to be an effective measuring device for hospital acquired infection management.