• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.12
• /
• pp.1069-1074
• /
• 2005

In this work, nano-needle structures ate formed to solve problem, related to low density of quantum dots for nano floating gate memory. Such structures ate fabricated and electrical properties' of MIS devices fabricated on the nano-structures are studied. Nano floating gate memory based on quantum dot technologies Is a promising candidate for future non-volatile memory devices. Nano-structure is fabricated by reactive ion etching using $SF_6$ and $O_2$ gases in parallel RF plasma reactor. Surface morphology was investigated after etching using scanning electron microscopy Uniform and packed deep nano-needle structure is established under optimized condition. Photoluminescence and capacitance-voltage characteristics were measured in $Al/SiO_2/Si$ with nano-needle structure of silicon. we have demonstrated that the nano-needle structure can be applicable to non-volatile memory device with increased charge storage capacity over planar structures.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.10a
• /
• pp.116-117
• /
• 2009

식각 공정변화 즉 상부 ICP 파워, 반응기 압력, 실리콘 기판 온도변화에 따른 실리콘 딥 비어 (deep via) 의 형상 변화 메커니즘을 연구하였다. 메커니즘을 연구하기 위해 $SF_6/O_2$ 플라즈마에 노출된 실리콘 기판의 공정변화에 따른 표면 온도변화를 실시간으로 측정하여 플라즈마 내 positive ions의 거동을 분석하였다. 실리콘 기판의 표면온도를 상승시키는 주된 요인은 positive ions임을 확인할 수 있었으며 이는 기판에 적용된 negative voltage로 인하여 나타난 이온포격이 그 원인임을 알 수 있었다. 상대적으로 radical은 실리콘 표면온도 상승에 큰 역할을 하지 못하였다. 기판 표면온도가 상승 할수록 실리콘 딥 비어 구조에 undercut, local bowing과 같은 측벽 식각이 활성화됨을 확인할 수 있었으며 이는 기판에 들어오는 positive ions가 측벽식각을 유도하는 것으로 해석할 수 있었다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.362-369
• /
• 2011

In this paper, optimal deep reactive ion etching (DRIE) process conditions for fused quartz were experimentally determined by Taguchi method, and fused quartz-based micro cantilevers were fabricated. In addition, comparative study on Q-factors of fused quartz and silicon micro cantilevers was performed. Using a silicon layer as an etch mask for fused quartz DRIE process, different 9 flow rate conditions of $C_4F_8$, $O_2$ and He gases were tested and the optimum combination of these factors was estimated. Micro cantilevers based on fused quartz were fabricated from this optimal DRIE condition. Through conventional silicon DRIE process, single-crystalline silicon micro cantilevers whose dimensions were similar to those of quartz cantilevers were also fabricated. Mechanical Q-factors were calculated to compare intrinsic damping properties of those two materials. Resonant frequencies and Q-factors were measured for the cantilevers having fixed widths and thicknesses and different lengths. The Q-factors were in a range of 64,000 - 108,000 for fused quartz cantilevers and 31,000 - 35,000 for silicon cantilevers. The experimental results supported that fused quartz had a good intrinsic damping property compared to that of single crystalline silicon.

• KSTLE International Journal
• /
• v.9 no.1_2
• /
• pp.10-12
• /
• 2008

Silicon micro-patterns were fabricated on Si (100) wafers using photolithography and DRIE (Deep Reactive Ion Etching) fabrication techniques. The patterned shapes included micro-pillars and micro-channels. After the fabrication of the patterns, the patterned surfaces were chemically modified by coating Z-DOL (perfluoropolyether, PFPE) thin films. The surfaces were then evaluated for their micro-friction behavior in comparison with those of bare Si (100) flat, Z-DOL coated Si (100) flat and uncoated Si patterns. Experimental results showed that the chemically treated (Z-DOL coated) patterned surfaces exhibited the lowest values of coefficient of friction when compared to the rest of the test materials. The results indicate that a combination of both the topographical and chemical modification is very effective in reducing the friction property. Combined surface treatments such as these could be useful for tribological applications in miniaturized devices such as Micro/Nano-Electro-Mechanical-Systems (MEMS/NEMS).

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.93-99
• /
• 2011

This paper presents a new type of optical silicon accelerometer using deep reactive ion etching (DRIE) and micro-stereolithography technology. Optical silicon accelerometer is based on a mass suspended by four vertical beams. A vertical shutter at the end of the mass can only moves along the sensing axis in the optical path between two single-mode optical fibers. The shutter modulates intensity of light from a laser diode reaching a photo detector. With the DRIE technique for (100) silicon, it is possible to etch a vertical shutter and beam. This ensures low sensitivity to accelerations that are not along the sensing axis. The microstructure for sensor packaging and optical fiber fixing was fabricated using micro stereolithography technology. Designed sensors are two types and each resonant frequency is about 15 kHz and 5 kHz.

• Clean Technology
• /
• v.9 no.3
• /
• pp.101-105
• /
• 2003

Plasma etching technology has been developed since it is recognized that silicon etching is very crucial in MEMS(Micro Electro Mechanical System) technology. In this study ICP(Inductive Coupled Plasma) technology was used as a new plasma etching to increase ion density without increasing ion energy, and to maintain the etching directions. This plasma etching can be used for many MEMS applications, but it has been used for PCR(Polymerase Chain Reaction) device fabrication. Platen power, Coil power and process pressure were parameters for observing the etching rate changes. Conclusively Platen power 12W, Coil power 500W, etchng/passivation cycle 6/7sec gives the etching rate of $1.2{\mu}m/min$ and sidewall profile of $90{\pm}0.7^{\circ}$, exclusively. It was concluded from this study that it was possible to minimize the environmental effect by optimizing the etching process using SF6 gas.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.2
• /
• pp.35-39
• /
• 2009

A novel Helmholtz coil inductively coupled plasma(H-ICP) etcher is proposed and characterized for deep nano-scale CMOS technology. Various hardware tests are performed while varying key parameters such as distance between the top and bottom coils, the distance between the chamber ceiling and the wafer, and the chamber height in order to determine the optimal design of the chamber and optimal process conditions. The uniformity was significantly improved by applying the optimum conditions. The plasma density obtained with the H-ICP source was about $5{\times}10^{11}/cm^3$, and the electron temperature was about 2-3 eV. The etching selectivity for the poly-silicon gate versus the ultra-thin gate oxide was 482:1 at 10 sccm of $HeO_2$. The proposed H-ICP was successfully applied to form multiple 60-nm poly-silicon gate layers.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.1
• /
• pp.6-14
• /
• 2012

For integrated complementary metal oxide semiconductor (CMOS) circuits, the lateral spread for two-dimensional (2-D) impurity distributions are very important for the analyzing the devices. The measured two-dimensional SEM data obtained using the chemical etching-method matched very well with the results of the Gauss model for boron implanted samples. But the profiles in boron implanted silicon were deviated from the Gauss model. The profiles in boron implanted silicon were shown a little bit steep profile in the deep region due to backscattering effect on the near surface from the bombardments of light boron ions. From the simulated 3-D data obtained using an analytical model, the 1-D and 2-D data were compared with the experimental data and could be verified the justification from the experimental data. The data of 3-D model were also shown good agreements with the experimental and the simulated data. It can be used in the 3-D chip design and the analysis of microelectro-mecanical system (MEMS) and special devices.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.9
• /
• pp.1020-1025
• /
• 2012

In this study, we fabricated the superhydrophobic and super-water-repellent surface with the micro/nano scale structures using simple conventional silicon wet-etching technique and the black silicon method by deep reactive ion etching. These fabrication methods are simple but very effective. Also we reported the droplet impact experimental results on the micro/nano-scaled surface. There are two representative impact behaviors as "rebound" and "fragmentation". We found the transition Weber number between "rebound" and "fragmentation" statements, experimentally. Additionally, we concerned about the dimensionless spreading diameters for our super-water-repellent surface. The novel characterization method was introduced for analysis including the "fragmentation" region. As a result, our super-water-repellent surface with the micro/nano-scaled structures shows the different impact behaviors compared with a reference smooth surface, by some meaningful experiments.

• ETRI Journal
• /
• v.28 no.3
• /
• pp.389-392
• /
• 2006

In this letter, a laterally-driven bistable electromagnetic microrelay is designed, fabricated, and tested. The proposed microrelay consists of a pair of arch-shaped leaf springs, a shuttle, and a contact bar made from silicon, low temperature oxide (LTO), and gold composite materials. Silicon-on-insulator wafers are used for electrical isolation and releasing of the moving microstructures. The high-aspect-ratio microstructures are fabricated using a deep reactive ion etching (DRIE) process. The tandem-typed leaf springs with a silicon/gold composite layer enhance the mechanical performances while reducing the electrical resistance. A permanent magnet is attached at the bottom of the silicon substrate, resulting in the generation of an external magnetic field in the direction vertical to the surface of the silicon substrate. The leaf springs show bistable characteristics. The resistance of the pair of leaf springs was $7.5\;{\Omega}$, and the contact resistance was $7.7\;{\Omega}$. The relay was operated at ${\pm}0.12\;V$.