• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.20-25
• /
• 1989

The nonlinear, time dependent photon transport equations of Frantz and Nodvik, which describe the amplification of an optical pulse in an active medium, are modified to a simpler equation which describes only the amplification of energy. with this equation, the output energy of the high power YLF(Nd3+)-Phosphate Glass(Nd3+) Laser System is calculated. When the stored energy density Est is 0.10J/㎤, 0.16J/㎤, 0.228J/㎤, and 0.50J/㎤, and with the assumption of uniform population inversion density, the final output energy of this laser system is 5.38J, 176J, 317J, and 283J, respectively. The gain saturation causes distortion of the output beam. This phenomenon is described in detail at the first three rod amplifier systems in the case of E=0.228J/㎤. The peak current and decay time constant of the flashlamps, which are used to obtain population inversion in the active medium, are investigated. The flashlamp driving circuit which has optimum operational performance should have {{{{ SQRT { LC} }} time about 100$\mu$sec.

• Current Photovoltaic Research
• /
• v.3 no.4
• /
• pp.107-111
• /
• 2015

Current characteristic curve of an illuminated solar cell was used to determine its reverse saturation current density ($J_0$), ideality factor (n) and resistances, by using numerical diode simulation. High efficiency amorphous silicon, heterojunction crystalline Si (HIT), plastic and organic-inorganic halide perovskite solar cell shows n=3.27 for a-Si and n=2.14 for improved HIT cell as high and low n respectively, while the perovskite and plastic cells show n=2.56 and 2.57 respectively. The $J_0$ of these cells remain within $7.1{\times}10^{-7}$ and $1.79{\times}10^{-8}A/cm^2$ for poorer HIT and improved perovskite solar cell respectively.

• Current Photovoltaic Research
• /
• v.2 no.3
• /
• pp.135-139
• /
• 2014

Different power output of solar cells can be observed at high-temperature regions such as desert areas. In this study, performance dependence on operating temperature of crystalline silicon solar cells with different emitter types was analyzed. Based on the light current-voltage (LIV) measurement, temperature coefficients of short-circuit current density ($J_{SC}$), open-circuit voltage ($V_{OC}$), fill factor (FF) and power conversion efficiency were measured and compared for two groups of crystalline silicon solar cells with different emitter types. One group had homogeneously doped (conventional) emitter and another selectively doped (selective) emitter. Varying the operating temperature from 25 to 40, 60, and $80^{\circ}C$, LIV characteristics of the cells were measured and the properties of saturation current densities ($J_0$) were extracted from dark current-voltage (DIV) curve. From the DIV data, effect of temperature on the performance of the solar cells with different electrical structures for the emitter was analyzed. Increasing the temperature, both emitter structures showed a slight increase in $J_{SC}$ and a rapid degradation of $V_{OC}$. FF and power conversion efficiency also decreased with the increasing temperature. The degrees of $J_{SC}$ increase and $V_{OC}$ degradation for two groups were compared and explained. Also, FF change was explained by series and shunt resistances from the LIV data. It was concluded that the degradation of solar cells shows different values at different temperatures depending on the emitter type of solar cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.404-404
• /
• 2016

태양전지 제작 시 표면에 피라미드 구조를 형성하면 입사되는 광의 흡수를 높여 광 생성 전류의 향상에 기여한다. 일반적인 KOH를 이용한 습식 표면조직화 공정은 평균 10%의 반사율을 보였으며, 유도 결합 플라즈마를 이용한 RIE 공정은 평균 5.4%의 더 낮은 반사율을 보였다. 그러나 RIE 공정을 이용한 표면조직화는 낮은 반사율과 서브 마이크론 크기의 표면 구조를 만들 수 있지만 플라즈마 조사에 의한 표면 손상이 많이 발생하게 된다. 이러한 표면 손상은 태양전지 제작 시 표면에서 높은 재결합 영역으로 작용하게 되어 포화 전류(saturation currents, $J_0$)를 증가시키고 캐리어 수명(carrier lifetime, ${\tau}$)을 낮추는 결함 요소로 작용한다. 이러한 플라즈마에 의한 표면 손상을 제거하기 위해 HF, HNO3, DI-water를 이용하여 DRE(Damage Remove Etching) 공정을 진행하였다. DRE 공정은 HF : DI-water 솔루션과 HNO3 : HF : DI-water 솔루션의 두 가지 공정을 이용하여 공정 시간을 가변하며 진행하였다. 포화전류($J_0$), 캐리어 수명(${\tau}$), 벌크 캐리어 수명(Bulk ${\tau}$)을 비교를 하기위해 KOH, RIE, RIE + DRE 공정을 진행한 세 가지 샘플로 실험을 진행하였다. DRE 공정을 적용할 경우 공정 시간이 지날수록 반사도가 높아지는 경향을 보였지만, 두 번째의 최적화된 솔루션 공정에서 $2.36E-13A/cm^2$, $42{\mu}s$의 $J_0$, Bulk ${\tau}$값과 가장 높은 $26.4{\mu}s$의 ${\tau}$를 얻을 수 있었다. 이러한 결과는 오제 재결합(auger recombination)이 가장 많이 발생하는 지역인 표면과 불균일한 도핑 영역에서 DRE 공정을 통해 나아진 표면 특성과 균일한 도핑 프로파일을 형성하게 되어 재결합 영역과 $J_0$가 감소 된 것으로 판단된다. 높아진 반사도의 경우 $SiN_x$를 이용한 반사방지막을 통해 표면 반사율을 1% 이내로 내릴 수 있어 보완이 가능하였다. 본 연구에서는 RIE 공정 중 플라즈마에 의해 발생하는 표면 손상 제거를 통하여 캐리어 라이프 타임의 향상된 조건을 찾기 위한 연구를 진행하였으며, 기존 RIE 공정에 비해 반사도의 상승은 있지만 플라즈마로 인한 표면 손상을 제거하여 오제 재결합에 의한 발생하는 $J_0$를 낮출 수 있었고 높은 ${\tau}$값인 $26.4{\mu}s$의 결과를 얻어 추후 태양전지 제작에 향상된 효율을 기대할 수 있을 것으로 기대된다.

• Current Applied Physics
• /
• v.18 no.11
• /
• pp.1248-1254
• /
• 2018

Magnetization versus temperature and magnetic-field measurements, M(T, $H_a$), have been carried out to study the magnetic and critical properties of polycrystalline $La_{1-x}Ba_xCoO_3$ (x = 0.3 and 0.5) cobaltites. These compounds with the density of ${\sim}6.2g/cm^3$ crystallized in the $R{\bar{3}}c$ rhombohedral and $Pm{\bar{3}}m$ cubic structures, respectively. With an applied field $H_a=200Oe$, M(T) data have revealed that the samples with x = 0.3 and 0.5 exhibit the ferromagnetic-paramagnetic (FM-PM) phase transition at the Curie temperature points $T_C=202$ and 157 K, respectively. At 4.2 K, the saturation magnetization ($M_{sat}$) decreases from 35.9 emu/g for x = 0.3-26.1 emu/g for x = 0.5. Particularly, the critical-behavior analyses in the vicinity of $T_C$ reveal all samples undergoing a second-order phase transition, with critical exponent values (${\beta}=0.328$ and ${\gamma}=1.251$ for x = 0.3, and ${\beta}=0.331$ and ${\gamma}=1.246$ for x = 0.5) close to those expected for the 3D Ising model. This proves short-range magnetic order existing in $La_{1-x}Ba_xCoO_3$. We believe that magnetic inhomogeneities due to the mixture of hole-rich FM regions (confined in the trivalent-cobalt hole-poor anti-FM matrix) and uniaxial anisotropy prevent long-range order in $La_{1-x}Ba_xCoO_3$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.176-176
• /
• 2003

The effects of oxide thickness and gate length of MgO/GaN metal oxide semiconductor field effect transistors (MOSFETs) on I-V, threshold voltage and breakdown voltage characteristics were examined using a drift-diffusion model. The saturation drain current scales in an inverse logarithmic fashion with MgO thickness and is < 10$^{-3}$ A.${\mu}{\textrm}{m}$$^{-1}$ for 0.5 ${\mu}{\textrm}{m}$ gate length devices with oxide thickness > 600 $\AA$ or for all 1 ${\mu}{\textrm}{m}$ gate length MOSFETs with oxide thickness in the range of >200 $\AA$. Gate breakdown voltage is > 100 V for gate length >0.5 ${\mu}{\textrm}{m}$ and MgO thickness > 600 $\AA$. The threshold voltage scales linearly with oxide thickness and is < 2 V for oxide thickness < 800 $\AA$ and gate lengths < 0.6 ${\mu}{\textrm}{m}$. The GaN MOSFET shows excellent potential for elevated temperature, high speed applications.

• Journal of Information Display
• /
• v.4 no.2
• /
• pp.1-6
• /
• 2003

In this paper, we demonstrate that the organic electrophosphorescent device is driven by the organic thin film transistor with spin-coated photoacryl gate insulator. It was found that electrical output characteristics in our organic thin film transistors using the staggered-inverted top-contact structure showed the non-saturated slope in the saturation region and the sub-threshold nonlinearity in the triode region, where we obtained the maximum power luminance that was about 90 $cd/m^2$. Field effect mobility, threshold voltage, and on-off current ratio in 0.45 ${\mu}m$ thick gate dielectric layer were 0.17 $cm^2/Vs$, -7 V, and $10^6$ , respectively. In order to form polyimide as a gate insulator, vapor deposition polymerization process was also introduced instead of spin-coating process, where polyimide film was co-deposited by high-vacuum thermal evaporation from 4,4'-oxydiphthalic anhydride (ODPA) and 4,4'-oxydianiline (ODA) and cured at 150${\sqsubset}$for 1hr. It was also found that field effect mobility, threshold voltage, on-off current ratio, and sub-threshold slope with 0.45 ${\mu}m$ thick gate dielectric films were 0.134 $cm^2/Vs$, -7 V, and $10^6$ A/A, and 1 V/decade, respectively.

• Current Applied Physics
• /
• v.18 no.12
• /
• pp.1496-1506
• /
• 2018

Organic/inorganic ultraviolet photodetector was fabricated using thermal evaporation technique. Organic/inorganic heterojunction based on thermally evaporated copper (II) acetylacetonate thin film of thickness 200 nm deposited on an n-type silicon substrate is introduced. I-V characteristics of the fabricated heterojunction were investigated under UV illumination of intensity $65mW/cm^2$. The diode parameters such as ideality factor, n, barrier height, ${\Phi}_B$, and reverse saturation current, $I_s$, were determined using thermionic emission theory. The series resistance of the fabricated diode was determined using modified Nord's method. The estimated values of series resistance and barrier height of the diode were about $0.33K{\Omega}$ and 0.72 eV, respectively. The fabricated photodetector exhibited a responsivity and specific detectivity about 9 mA/W and $4.6{\times}10^9$ Jones, respectively. The response behavior of the fabricated photodetector was analyzed through ON-OFF switching behavior. The estimated values of rise and fall time of the present architecture under UV illumination were about 199 ms and 154 ms, respectively. Finally, enhancing the photoresponsivity of the fabricated photodetector, post-deposition plasma treatment process was employed. A remarkable modification of the device performance was noticed as a result of plasma treatment. These modifications are representative in a decrease of series resistance and an increase of photoresponsivity and specific detectivity. The process of plasma treatment achieved an increment of external quantum efficiency from 5.53% to 8.34% at -3.5 V under UV illumination.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.471.2-471.2
• /
• 2014

We demonstrate here that an improvement in precursor film density (green density) leads to a great enhancement in the photovoltaic performance of CuInSe2 (CISe) thin film solar cells fabricated with Cu-In nanoparticle precursor films via chemical solution deposition. A cold-isostatic pressing (CIP) technique was applied to uniformly compress the precursor film over the entire surface (measuring 3~4 cm2) and was found to increase its relative density (particle packing density) by ca. 20%, which resulted in an appreciable improvement in the microstructural features of the sintered CISe film in terms of lower porosity, reduced grain boundaries, and a more uniform surface morphology. The low-bandgap (Eg=1.0 eV) CISe PV devices with the CIP-treated film exhibited greatly enhanced open-circuit voltage (VOC, from 0.265 V to 0.413 V) and fill factor (FF, from 0.34 to 0.55), as compared to the control devices. As a consequence, an almost 3-fold increase in the average power conversion efficiency, 3.0 to 8.2% (with the highest value of 9.02%), was realized without an anti-reflection coating. A diode analysis revealed that the enhanced VOC and FF were essentially attributed to the reduced reverse saturation current density (j0) and diode ideality factor (n). This is associated with the suppressed recombination, likely due to the reduction in recombination sites such as grain/air surfaces (pores), inter-granular interfaces, and defective CISe/CdS junctions in the CIP-treated device. From the temperature dependences of VOC, it was confirmed that the CIP-treated devices suffer less from interface recombination.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.41.2-41.2
• /
• 2010

최근 태양전지 제조비용 절감을 위해 초박형 실리콘 태양전지 개발이 활발히 이루어지고 있다. 이에 따라 후면전계(Back Surface Field, BSF) 특성에 대한 관심이 높아지는 추세이다. 이에 본 연구에서는 후면의 결정방향 및 표면구조에 따라 형성되는 후면전계(BSF)의 특성에 대해 알아보고자 하였다. 후면이 절삭손상층 식각(Saw damage etching) 후 (100)면이 드러난 실리콘 기판과 텍스쳐링(Texturing) 후 (111)면이 드러난 실리콘 기판에 후면 전극을 스크린 인쇄 후 Ramp up rate을 달리 하여 소성 공정(RTP system)을 통해 후면전계(BSF)를 형성하여 비교하였다. 후면전계(BSF)의 형상과 특성만을 평가하기 위하여 염산을 이용하여 후면 전극층을 제거하였다. 후면 전극 제거 후 주사전자현미경(Scanning Electron Microscopy)과 3차원 미세형상측정기(Non-contacting optical profiler)로 후면전계(BSF)의 형상을 비교하였다. 또한 후면전계(BSF)의 특성을 평가하고자 Quasi-Steady-State Photo Conductance(QSSPC)를 사용하여 포화전류(Saturation current, $J_0$)을 측정하였고, 면저항 측정기(4-point probe)로 면저항을 측정하여 비교하였다. 후면 전계(BSF)는 (100)면과 (111)면에서 모두 Ramp up rate이 빠를수록 향상된 특성을 보였고, (111)면에서 더 큰 차이를 보였다.