• Journal of the Korean GEO-environmental Society
• /
• v.10 no.6
• /
• pp.99-103
• /
• 2009

This research is the result of investigating engineering characteristics of slime generated during construction of deep mixing method. Mechanical characteristics of slime have been studied through literature review and laboratory tests of unconfined compression test, permeability test and settling tests were performed. As result of field observation of slime being generated, slime started to be produced right after flight auger was penetrated into a ground and its amount was increased in progress. Unconfined compressive strength of specimen with slime obtained from in field was measured in the range of $929.7{\sim}3,509.8kN/m^2$ and the value of unconfined compressive strength was found to be changed significantly with mixing ratio of soil, cement and binder. Permeability of them was measured in the range of $4.53{\times}10^{-7}{\sim}6.62{\times}10^{-6}cm/sec$ so that the mixture was appropriate as a impervious barrier. It was also know that the value of permeability was changed with the mixing ratio of binder. As test results of solidifying slime specimen prepared in the laboratory, good quality of cement mixture with coarse soil of sand were produced, compared with fine soils of silt and clay.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.1
• /
• pp.109-120
• /
• 2004

There has been outstanding research on the soil-water characteristic curves of unsaturated soils over the past several decades. Unfortunately, unsaturated soil mechanics has not been considered as an important factor in Korea. In this paper, laboratory test and numerical analysis(SoilVision Professional ver 3.04) were performed to investigate the prediction method of soil-water characteristic curve and unsaturated permeability coefficient in reclaimed ground. The pressure cell, desiccator, and tensiometor tests were conducted on three types of reclaimed soils(dredged soil, sand, weathered granite soil). Numerical analysis was executed to compare the results with the laboratory test results and also compared with the results of each prediction method. Based on the laboratory test, three different types of soils have shown different soil-water characteristic curves. The hysteresis fir these soils is clearly defined. As a result of numerical analysis, Fredlund & Xing's method and Fredlund & Wilson's model proved to worke out well for reclaimed ground soils in Korea. Also, predicting method based on the soil-water characteristic curves from the particle-size distributions is flirty reliable for estimating unsaturated permeability coefficient.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.449-455
• /
• 2019

The increase in impermeable pavement from recent urbanization has resulted in an increase in surface runoff. The surface runoff has also increased the burden of the existing drainage system. This drainage system has structural limitations in that the catchment area is reduced by the waste particles transported with the surface runoff. In addition, the efficiency of the drainage system is decreased. To overcome these limitations, a new type of drainage system with a drainage layer was developed and applied. In this study, various volume porosity and permeability of the lower drainage layer were simulated using ANSYS CFX, which is a three dimensional computational fluid dynamics program. The results showed that the outlet velocity of the 35% volume porosity was faster than that of the 20% and 50% cases, and there was no relationship between the volume porosity and drainage performance. The permeability of the drainage layer can be determined from the particle size of the material, and a simulation of five conditions showed that 2 mm sand grains are most suitable for workability and usability. This study suggests appropriate values of the volume porosity and particle size of the drainage layer. This consideration can be advantageous for reducing and preventing flood damage.

• The Journal of Engineering Geology
• /
• v.29 no.1
• /
• pp.51-68
• /
• 2019

This study performs to evaluate adaptability of seashore filtering type seawater-intake which adapts dua1 filter well alternative for direct seawater-intake. This study varies filter condition of seashore free surface aquifer which is composed of sand layer then installs real size dual filter well and single filter well to evaluate water permeability and proper pumping amount according to filter condition. According to result of step aquifer test, it is analysed that 110.3% synergy effect of water permeability coefficient is happened compare to single filter since dual filter well has better improvement. dual filter has higher water permeability coefficient compare to same pumping amount, this means dual filter has more improved water permeability than single filter. According to analysis result of continuous aquifer test, it is evaluated that dual filter well (SD1200) has higher water permeability than single filter well (SS800) by analysis of water permeability coefficient using monitoring well and gauging well, it is also analysed dual filter has 110.7% synergy effect of water permeability coefficient. As a evaluation result of pumping amount according to analysis of water level dropping rate, it is analysed that dual filter well increased 122.8% pumping amount compare to single filter well when water level dropping is 2.0 m. As a result of calculating proper pumping amount using water level dropping rate, it is analysed that dual filter well shows 136.0% higher pumping amount compare to single filter well. It is evaluated that proper pumping amount has 122.8~160% improvement compare to single filter, pumping amount improvement rate is 139.6% compare to averaged single filter. In other words, about 40% water intake efficiency can be improved by just installation of dual filter compare to normal well. Proper pumping amount of dual filter well using inflection point is 2843.3 L/min and it is evaluated that daily seawater intake amount is about $4,100m^3/day$ (${\fallingdotseq}4094.3m^3/day$) in one hole of dual filter well. Since it is possible to intake plenty of water in one hole, higher adaptability is anticipated. In case of intaking seawater using dual filter well, no worries regarding damages on facilities caused by natural disaster such as severe weather or typhoon, improvement of pollution is anticipated due to seashore sand layer acts like filter. Therefore, It can be alternative of environmental issue for existing seawater intake technique, can save maintenance expenses related to installation fee or damages and has excellent adaptability in economic aspect. The result of this study will be utilized as a basic data of site demonstration test for adaptation of riverside filtered water of upcoming dual filter well and this study is also anticipated to present standard of well design and construction related to riverside filter and seashore filter technique.

• The Journal of Engineering Geology
• /
• v.31 no.4
• /
• pp.493-506
• /
• 2021

Liquefaction refers to a phenomenon in which excessive pore water pressure occurs when a dynamic load such as an earthquake rapidly acts on a loose sandy soil saturated with soil, and the ground loses effective stress and becomes liquefied. The indoor repeated test for liquefaction evaluation can be confirmed through the repeated triaxial compression test and the repeated shear test. In this regard, this study tried to confirm the liquefaction resistance strength according to the relative density and particle size distribution of sand using the repeated triaxial compression test. As a result of the experiment, it was confirmed that the liquefaction resistance strength increased as the relative density increased regardless of the soil classification, and the liquefaction resistance strength according to the particle size distribution of the sand was confirmed that the liquefaction resistance strength of the SP sample close to SW was significantly higher. In addition, as a result of analyzing 30% of fine powder compared to 0% of fine powder, as the relative density increased to 40~70%, the liquefaction resistance strength decreased by 5~20%, and the domestic weathered soil ground had a fine liquefaction resistance strength compared to Jumunjin standard sand. When the minute was 10%, it was measured to be 30% or more, and when the fine particle was 30%, it was measured to be less than 50%.

• Korean Journal of Environment and Ecology
• /
• v.14 no.1
• /
• pp.38-45
• /
• 2000

This research has been done to investigate influence of soil physical and chemical properties on forest environmental change by fired pine forest in Koseong, Kangwondo. The sample sites were divided by not-fired sites(NF), not-cutting site after fired(FNC), cutting and planting sites after fired(FCP) and cutting and not-planting sites after fired(FC). Soil texture of whole sites was sandy clay loam. Sand content of NF top soil were lower than those of sub soil and clay content were higher, while FNC, FCP and FC sand content of top soil were higher than those of sub soil. Total porosity didn't differ between the sites. Coarse porosity and permeability had the increasing order as NF> FNC> FCP> FC, but fine porosity and bulk density had the opposite trends. Because forest fire removed the vegetation and then soil erosion was accelerated, forest environmental changes by forest fire greatly degraded soil porosity and permeability which were indices for forest water retention, so that soil physical properties were deteriorated. Both top and sub soil pHs of NF and FNC were higher than those of FCP and FC. Organic matter content and total nitrogen content of top and sub soils were high in order as NF> FNC> FCP> FC. Cation exchange capacities and exchangeable cation(K+, Na+, $Ca^2$+, $Mg^2$+) content in top soils were higher than those in sub soils, and in order as NF> FNC> FCP> FC, to be compared by the sites. Those mean that forest fire result from the erosion of top soil layers.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.5
• /
• pp.31-38
• /
• 2007

The practical design method on sandmat uses a drain length, rate of consolidation settlement and permeability of sand as a major design factors. And, on the basis of this design process, it has been installed beneath the embankment with same thickness. However, the possibility the underestimation on the thickness of sandmat and the delayed drain have been pointed out by several authors caused by a differential settlement at the center and the end of embankment. In this study, therefore, the effect of the differential settlement on the thickness of sandmat and delayed drain through the numerical analysis of embankment was analyzed. As a result, a substantial sandmat thickness becomes small and the possibility of the delayed drain can be certified because of the development of differential settlement at the center and ends of embankment. As a countermeasure to overcome this problem, the applicability of the mound type sandmat was also investigated by the numerical method. It can be concluded that it maintains the designated substantial sandmat thickness throughout consolidation process, and is useful method to maintain the drain capacity. Especially, the mound type sandmat is effective method for a construction site where can cause a differential settlement such as embankment. Furthermore, it has to be designed on the basis of the accurate prediction of consolidation settlement as well as rate of consolidation settlement, drain length and permeability of sand.

• Journal of the Korean Geosynthetics Society
• /
• v.15 no.3
• /
• pp.39-47
• /
• 2016

In order to prevent leakage of leachate in offshore landfill, hydraulic barrier is indispensable. In the case of rubble mound revetment at offshore landfill, HDPE sheet in slope should be installed. In this study, seepage analysis were performed to evaluate seepage and flow in the seabed and revetment according to extended length of HDPE sheet by using SEEP/W. Results show that, in the case of low permeability layer is distributed where extended length of HDPE sheet was more than 1m, seepage flux in seabed and revetment was greatly reduced. In order to prevent seepage in seabed and revetment in the case of sand layer of high permeability is existed above low permeable layer, extended length of HDPE sheet and impermeable improvement width of permeable layer should be more than 1m at seabed.

• Geotechnical Engineering
• /
• v.12 no.5
• /
• pp.5-16
• /
• 1996

When braced excavation with temporary retaining wall installation, is performed in loose sand with high ground water level boiling may be induced and considerable damage on the excavation works and structures in the vicinity can take place. Recently, for the purpose of reinforcement of ground and cut-off of ground water behind the temporary retaining wall, high pressure jet grouting is widely used. The purpose of this paper is to investigate the effects of jet grouting on ground reinforcement and cut -off of the ground water behind temporary retaining walls for braced excavation. A series of both laboratory and field tests has been performed. The test results show that high pressure jet grouting has sufficient effects on reinforcement of stiffness of ground and retaining wall. The permeability of the improved ground was 10-f_ 10-3cm l s smaller than those of the original ground. Therefore, the effect on cut off of ground water behind temporary retaining walls could be improved by high pressure jet grouting method.

• Geomechanics and Engineering
• /
• v.17 no.4
• /
• pp.367-374
• /
• 2019

This study concluded the results of a research on the features of cement based permeation grout, based on some important grout parameters, such as the rheological properties (yield stress and viscosity), coefficient of permeability to grout ($k_G$) and the inject ability of cement grout (N and $N_c$ assessment), which govern the performance of cement based permeation grouting in porous media. Due to the limited knowledge of these important grout parameters and other influencing factors (filtration pressure, rate and time of injection and the grout volume) used in the field work, the application of cement based permeation grouting is still largely a trial and error process in the current practice, especially in the local construction industry. It is seen possible to use simple formulas in order to select the injection parameters and to evaluate their inter-relationship, as well as to optimize injection spacing and times with respect to injection source dimensions and in-situ permeability. The validity of spherical and cylindrical flow model was not verified by any past research works covered in the literature review. Therefore, a theoretical investigation including grout flow models and significant grout parameters for the design of permeation grouting was conducted in this study. This two grout flow models were applied for three grout mixes prepared for w/c=0.75, w/c=1.00 and w/c=1.25 in this study. The relations between injection times, radius, pump pressure and flow rate for both flow models were investigated and the results were presented. Furthermore, in order to investigate these two flow model, some rheological properties of the grout mixes, particle size distribution of the cement used in this study and some geotechnical properties of the sand used in this work were defined and presented.