• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.4
• /
• pp.137-146
• /
• 1999

Inspection becomes to be important in the safety of structure and economical viewpoint, because structural damage accompanies lots of economical cost and social problems. Especially ship structure is composed of a lot of members and it is impossible to inspect all members continuously. The purpose of this paper is to get optimal inspection plan containing inspection time and method. Crack is one of major modes on the structural failure and can lead to collapse of structure. In this paper, the deteriorating process, which contains inspection to detect the crack before the propagation to large crack, is idealized as Markov chain model. Genetic algorithm is also used to accomplish the optimization of inspection plan. Especially, the probabilistic characteristics of cracks are changed, because ship is operating in corrosive environments and the scantling of structural members is reduced due to corrosion. Non-stationary Markov chain model is used to represent the process of corrosion in structural members. In this paper, the characteristics of indivisual inspection plan are compared by numerical examples for the change of corrosion rate, the cost due to scheduled system down and target failure probability. From the numerical example, it can be seen that the improvement of fatigue life for the members with short fatigue life is the most effective way in order to reduce total maintenance cost.

• Journal of the Korean Magnetics Society
• /
• v.17 no.4
• /
• pp.147-151
• /
• 2007

We have investigated the half-metallicity and magnetism for the Heusler ferromagnet $Co_2$ZrSi interfaced with semiconductor ZnTe along the (001) plane by using the full-potential linearized augmented plane wave (FLAPW) method. We considered low types of possible interfaces: ZrSi/Zn, ZrSi/Te, Co/Zn, and Co/Te, respectively. From the calculated density of states, it was found that the half-metallicity was lost at all the interfaces, however for the Co/Te system the value of minority spin density of states was close to zero at the Fermi level. These facts are due to the interface states, appeared in the minority spin gap in bulk $Co_2$ZrSi, caused by the changes of the coordination and symmetry and the hybridizations between the interface atoms. At the Co/Te interface, the magnetic moments of Co atoms are 0.68 and $0.78{\mu}_B$ for the "bridge" and "antibridge" sites, respectively, which are much reduced with respect to that ($1.15{\mu}_B$) of the bulk $Co_2$ZrSi. In the case of Co/Zn, Co atoms at the "bridge" and "antibridge" sites have magnetic moments of 1.16 and $0.93{\mu}_B$, respectively, which are almost same or slightly decreased compared to that of the bulk $Co_2$ZrSi. On the other hand, for the ZrSi/Zn and ZrSi/Te systems, the magnetic moments of Co atoms at the sub-interface layers are in the range of $1.13{\sim}1.30\;{\mu}_B$, which are almost same or slightly increased than that of the bulk $Co_2$ZrSi.

• Journal of the Korean association of regional geographers
• /
• v.3 no.1
• /
• pp.1-12
• /
• 1997

The climatic characteristics of Korea are analized with the data observed from 1972 to 1995 in 66 stations, using the climatic year method expressed by the $K{\ddot{o}}ppen's$ system of climatic classification. The climate of Korea is composed of the six climatic year types : Cfa, Cwa, Cwb, Dfa, Dwa and Dwb type. The Cwa and Dwa type occupy 95% occurrence frequency. The Cwa climatic year type predominates in the greater part of the Southern Area, the east slopes of the Taebaek Range and Cheju-do, the Dwa type does in Yongso Area and the northeastern part of Kyonggi Province. and the Cfa type does in Ullung-do. Such dominant climatic year regions become the stable climatic regions, while the regions where the various climatic types appear become the unstable climatic regions which are distributed in the northern part of the Southern Area and in the southern part of the Central Area owing to the shifts of the border between C type and D type. The border between C and D type is located in the Central Inland Area in the first half of the 1990's which the Cwa type predominates most. On the other hand the border is located in the middle part of the Southern Area in the first half of the 1980's which the Dwa type prevails most. Therefore the extents of the climatic year regions vary each year. In the interannual change of the main climatic year types, the Cwa type shows the increasing trend, while the Cfa and Dwa type reflets the decreasing tendency. The extending trend of the Cwa climatic year region appears during the period of the first half of the 1970's and the period between the latter half of the 1980's and the first half of the 1990's centering around the Southern Area. The Dwa climatic year region which was predominant in the Central Area in the first half of the 1980's has been reduced up till the recent years.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.1
• /
• pp.48-57
• /
• 2020

MCU used in applications such as wireless chargers and USB type-C require MTP memory with a small cell size and a small additional process mask. Conventional double poly EEPROM cells are small in size, but additional processing masks of about 3 to 5 sheets are required, and FN tunneling type single poly EEPROM cells have a large cell size. In this paper, a 110nm MTP cell using a vertical PIP capacitor is proposed. The erase operation of the proposed MTP cell uses FN tunneling between FG and EG, and the program operation uses CHEI injection method, which reduces the MTP cell size to 1.09㎛2 by sharing the PW of the MTP cell array. Meanwhile, MTP memory IP required for applications such as USB type-C needs to operate over a wide voltage range of 2.5V to 5.5V. However, the pumping current of the VPP charge pump is the lowest when the VCC voltage is the minimum 2.5V, while the ripple voltage is large when the VCC voltage is 5.5V. Therefore, in this paper, the VPP ripple voltage is reduced to within 0.19V through SPICE simulation because the pumping current is suppressed to 474.6㎂ even when VCC is increased by controlling the number of charge pumps turned on by using the VCC detector circuit.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.10
• /
• pp.6336-6343
• /
• 2014

The aim of this study was to consider new 3D printing techniques and how to use them in architecture, compare the 3D printing and current techniques, and analyze them economically. 3D printing technology is expected to result in considerable changes to the entire system, such as production and distribution using this new technology in the near future. In addition, architecture is expected to follow this trend. This study examined how to take advantage of 3D printing technology in construction to prepare for a new architectural trend of 3D printing technology in the future. This study examined the 3D printing technology that is used in buildings and the current state of 3D printing technology. In addition, the 3D printing technology and current technology was also compared, and analyzed economically. 3D printing technology is the step before the stage of practical use. On the other hand, the commercialization of 3D printing technology makes it possible to reduce the cost compared to the current method. Furthermore, as the technology is developed in the future, the cost is expected to be reduced further. Therefore, the use of 3D printing technology in architecture is expected increase continually.

• Journal of the Korean Institute of Gas
• /
• v.24 no.1
• /
• pp.17-22
• /
• 2020

Light Naphtha is distillated from crude oil unit and separated into the methane, ethylene and propylene by boiling point difference in sequence. This separation is conducted using a series of binary-like columns. This separation method is known that the energy consumed in the reboiler is used to separate the heaviest components and most of this energy is discarded as vapor condensation in the overhead cooler. In this study, the first two columns of the separation process are replaced with the Petlyuk column. A structural design was exercised by the stage computation with ideal tray efficiency in equilibrium condition. Compared with the performance of a conventional system of 3-column model, The design outcome shows that the procedure is simple and efficient because the composition of the liquid component in the column tray was designed to be similar to the equilibrium distillation curve. The performance of the new process indicates that an energy saving of 12.1% is obtained and the cost savings of 44 million won per day based on gross domestic product is reduced under same total number of trays and the initial investment cost is saved.

• Journal of Internet Computing and Services
• /
• v.17 no.6
• /
• pp.33-39
• /
• 2016

With recent advances in sensor technology, CMOS-based semiconductor devices and networking protocol, the areas for application of wireless sensor networks greatly expanded and diversified. Such diversification of uses for wireless sensor networks creates a multitude of beneficial possibilities for several industries. In the application of wireless sensor networks for monitoring systems' data transmission process from the sensor node to the sink node, transmission through multi-hop paths have been used. Also mobile sink techniques have been applied. However, high energy costs, unbalanced energy consumption of nodes and time gaps between the measured data values and the actual value have created a need for advancement. Therefore, this thesis proposes a new model which alleviates these problems. To reduce the communication costs due to frequent data exchange, a State Prediction Model has been developed to predict the situation of the peripheral node using a geographic autocorrelation of sensor nodes constituting the wireless sensor networks. Also, a Risk Analysis Model has developed to quickly alert the monitoring system of any fatal abnormalities when they occur. Simulation results have shown, in the case of applying the State Prediction Model, errors were smaller than otherwise. When the Risk Analysis Model is applied, the data transfer latency was reduced. The results of this study are expected to be utilized in any efficient communication method for wireless sensor network monitoring systems where all nodes are able to identify their geographic location.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.6
• /
• pp.744-753
• /
• 2021

This study suggests ways to improve the standard test method and judgment criterion for the "Eco-toxicity Test" based on the rules and regulations provided in 'performance and qualifying test standards for marine pollution prevention materials and chemicals' in the Republic of Korea. Compared with the relevant references of other countries, this study attempted to find the limitations in the existing standards. As for the growth inhibition test of algae using Skeletonema costatum as an indicator, applying comparative analysis to measure specific growth rates, together with statistical analysis, instead of applying current methods, judged by the appearance of colors from the culture medium was suggested. Considering the exponential growth phase of the test species, the test duration was suggested to be reduced to less than four days. For the test with fish as an indicator, resetting the appropriate body size was suggested to, show consistent sensitivity against chenicals applied during testing. Furthermore, it is necessary to consider the criteria needs, which should be established in reasonable and objective ways. For the testing species, marine rotifer, Brachionus plicatilis could be a replacement for Artemia sp., and a bivalve for fish in the test. To improve the performance effectiveness of the "Eco-toxicity test", it is worth considering the designation of accredited testing institutes, by placing it in the same loop. Thus it is also expected to have a reliable management system in place, having the capacity of cost calculation properly and adjusting testing items if required.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.378-384
• /
• 2019

In the food wastewater treatment facilities, the water quality improvement effect and the greenhouse gas emission amount followed by the change in electricity usage through a change of the aeration tank ventilation system were evaluated. also, the amount of greenhouse gas emission followed by the change in electricity usage through the change of the sludge dewatering, storage, transporting method was also evaluated. The total GHG emission from food wastewater treatment facility improvement were divided into direct emissions from the treatment processes and indirect ones from electricity usage. The water quality improvement effect of wastewater treatment plant was found to be 63.3% for BOD removal rate, 42.0% for COD removal rate, 71.0% for SS removal rate and 39.6% for T-N removal rate. and according to the results of calculating output by applying both direct emissions of greenhouse gas (Scope 1) and the indirect emission (Scope 2) of greenhouse gas followed by changes in power consumption. It was estimated that there was a total of 276.0tCO2eq./yr(7.5%) greenhouse gas reduction effect from 3,668.8tCO2eq./yr before improvement to 3,392.8tCO2eq./yr after improvement. In this result is not due to the effects of water quality improvement of emission source, but because the reduction in electricity use has reduced the amount of greenhouse gas emissions.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.4
• /
• pp.468-475
• /
• 2019

An end-line flame arrester allows free venting in combination with flame protection for vertical vent applications. End-line flame arresters are employed in various fields, especially in shipping. In flame arresters, springs are essential parts because the spring load and the spring's elasticity determine the hood opening moment. In addition, the spring has to work under a high-temperature condition because of the burning gas flame. Therefore, it is necessary to analyze the mechanical load and elasticity of the spring when the flame starts to appear. Based on simulations of the working process of a specific end-line flame arrester, a thermal and structural analysis of the spring is performed. A three-dimensional model of a burned spring is built using computational fluid dynamics (CFD) simulation. Results of the CFD analysis are input into a finite element method simulation to analyze the spring structure. The research team focused on three cases of spring loads: 43, 93, and 56 kg, correspondingly, at 150 mm of spring deflection. Consequently, the spring load was reduced by 10 kg after 5 min under a $1,000^{\circ}C$ heat condition. The simulation results can be used to predict and estimate the spring's load and elasticity at the burning time variation. Moreover, the obtained outcome can provide the industry with references to optimize the design of the spring as well as that of the flame arrester.