• Journal of the Korean Society for Railway
• /
• v.18 no.1
• /
• pp.33-42
• /
• 2015

The vertical static stiffness of rail pads or baseplate pads, which are important components in rail fastening systems for track safety, is a key factor to determine the total track stiffness and a guideline of quality control in the manufacturing process. The vertical static stiffness can be checked by laboratory testing: test methods are EN 13146-9 and KRS TR 0014, which are widely used in the railway field. In this paper, to correct some problems, namely the preloading step, the unloading level, and the holding time in the loading program in the vertical static stiffness test of EN 13146-9 and KRS TR 0014, domestic and foreign test standards of pads were analyzed and then certain schemes for a vertical static stiffness test were proposed. To assess the reliability of the proposed schemes, the vertical static stiffness tests were performed with 4 pads and the validity of the test results was estimated.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1188-1195
• /
• 2007

The vertical forces in rail fasteners at areas of bridge transitions near the embankment and on the pier will occur due to different deformations of adjoining bridges caused by the trainloads, the settlement of supports, and the temperature gradients. The up-lifting forces is not large problem in the blast track because the elasticity of blast and rail pad buffs up-lifting effect. But, it is likely to be difficult to ensure the serviceability of the railway and the safety of the fastener in the end in that concrete slab track consist of rail, fastener, and track in a single body, delivering directly the up-lifting force to the fastener if the deck is bended because of various load cases, such as the end rotation of the overhang due to the vertical load, the bending of pier due to acceleration/braking force and temperature deviation, the settlement of embankment and pier, the temperature deviation of up-down deck and front-back pier, and the rail deformation due to wheel loads. The analysis of the rail fastener is made to verify the superposed tension forces in the rail fastener due to various load cases, temperature gradients and settlement of supports. The potential critical fasteners with the highest uplift forces are the fastener adjacent to the civil joint. The main influence factors are the geometry of the bridge such as, the beneath length of overhang, relative position of bridge bearing and fastener, deflection of bridge and the vertical spring stiffness of the fastener.

• Structural Engineering and Mechanics
• /
• v.75 no.4
• /
• pp.435-444
• /
• 2020

Ultrasonic guided wave testing is a very promising non-destructive testing method for rails, which is of great significance for ensuring the safe operation of railways. On the basis of the semi-analytical finite element (SAFE) method, a analytical model of 59R2 grooved rail was proposed, which is commonly used in the ballastless track of modern tram. The dispersion curves of ultrasonic guided waves in free rail and supported rail were obtained. Sensitivity analysis was then undertaken to evaluate the effect of rail elastic modulus on the phase velocity and group velocity dispersion curves of ultrasonic guided waves. The optimal guided wave mode, optimal excitation point and excitation direction suitable for detecting rail integrity were identified by analyzing the frequency, number of modes, and mode shapes. A sinusoidal signal modulated by a Hanning window with a center frequency of 25 kHz was used as the excitation source, and the propagation characteristics of high-frequency ultrasonic guided waves in the rail were obtained. The results show that the rail pad has a relatively little influence on the dispersion curves of ultrasonic guided waves in the high frequency band, and has a relatively large influence on the dispersion curves of ultrasonic guided waves in the low frequency band below 4 kHz. The rail elastic modulus has significant influence on the phase velocity in the high frequency band, while the group velocity is greatly affected by the rail elastic modulus in the low frequency band.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.471-478
• /
• 2000

For many decades, the railway was constructed using tracks with jointed rails of relatively short lengths. The joints cause many drawbacks in the track and lead to signeficant maintenance cost. so, railroad engineers became interested in eliminating joints. Continuous welded rail(CWR) track has many advantages over the conventional jointed-rail track. but, in the case of the elimination of rail joints, it may cause the track to be suddenly buckled laterally by thermal loads. In this paper, firstly, 3-D CWR track model and CWRB program exactly considering the influence of tie are developed far linear static and buckling analysis using finite element method. Characteristics of CWR track model are using 7-dofs beam element as rail, Offset technic exactly considering centroid axies difference of track components(rail, rail-pad-fastener, tie), and Thermal gradient considering thermal difference of top flange and bottom flange in rail section.. second,, Through the static and linear buckling analysis by CWRB, Influences of various track components (rail, ballast, fastener, tie and so on..) on CWR track behavior and stability was characterized.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.3
• /
• pp.58-64
• /
• 2007

The clamping force of a jaw pad is determined by the displacements of main part when two lockers are locked, after the clamping angle of a locker was set up in the wedge type rail clamp for a container crane. In this time, if the resistance of wedge frame generates due to several factors, the clamping angle of a locker to display the initial clamping force will be changed because of the reduction of displacement of extension bar. This resistance is determined by the eccentric distance between the roller and the wedge, and by the gap between the wedge frame and outer frame. In this study we measured the tensile force of both extension bar through the performance test of the prototype rail clamp in order to evaluate the effect of the resistance of wedge frame on the clamping force of the wedge type rail clamp.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2101-2106
• /
• 2011

It is reported that about more than 45% of damage shown in railroad rails include breakage of rail end which cross the center of Thermit welded zone. Thermite welding is always accompanied by numerous aluminum oxide and secondary inclusions, which may have a negative influence on the ductility and toughness of the weld metal. In this study the aluminum powder recycled by waste aluminum can was used for iron oxide generated after the process of welding rod and the remain aluminum was reduced by minimizing the quantity of aluminum. And complete dissolution was induced by using ferro Mn powder as the additive element. This study reviewed the applicability of heat treatment in the welded zone of rail using ceramic heating pad by carrying it out. This study could observe the improvement of the mechanical characteristics (UTS and elongation) and the changes of failure mechanism from brittleness to ductility. It could be found that improved strength and elongation result from pearilte fine structure.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.763-768
• /
• 2004

CWR(Continuous Welded Rail) has many advantage over the conventional jointed rail track. The use of CWR track not only reduces the track maintenance cost, but increase the life cycle of track components. As the use of CWR increases in track structures, derailing disasters associating with track buckling also increase in great numbers due to high compressive thermal stress. Despite the importance, the number of studies relevant to the instability is quite limited. In this paper, It considers the contribution of rail-pad-fastener resistance, uplift of tie and nonlinear analysis. Influence of various track components on CWR track temperature and mode shape were characterized.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.883-888
• /
• 2004

One of commercial rapid transits produces peculiar booming sound when passing through the slab-track tunnel. In order to analyze that tympanic membrane-pressing noise systematically, typical source-transfer path-response analysis was carried out. Considering the octave band of booming noise, work scope was confined to structure-borne noise analysis, especially the dynamic behaviour of railway tracks. Experimental modal analysis of railway tracks, composed of rail, rubber pad, sleeper, ballast, and ground were performed. The results shows that transversal bending modes of the rail are suspicious for the cause of the low band booming noise. Finite element analysis are made use of to match preceding experimental results, and plausible dynamic properties of track components are produced.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1056-1064
• /
• 2008

It is estimated that the running of locally-developed next generation High Speed Trains with maximum speed of 400km/h will help to deteriorate track components. It was presented rail defect coding system in UIC 712R includes the definitions of damage types of rail, maintenance procedures, and etc to detect and maintain. It is necessary to make a track maintenance manual determining track maintenance periods using the standardization of damage types of track components such as: sleeper, fastener, elastic pad. In this paper, the damage types of high speed track components are investigated by referring domestic and foreign literatures. And then the damage types of rail given in UIC 712R is reclassified more particularly and classified damage types of track components using internal high speed railway. In conclusion, this paper suggests standardization for damage types of track components on internal high speed railway.

• 연구논문집
• /
• s.34
• /
• pp.101-112
• /
• 2004

In order to analyze the motion errors of the aerostatic stage, it is necessary to consider the influence of the moment variation occurredinside the pads. In this paper, a motion error anaysis method utilizing the transfer functions on the reaction force and moment is proposed, and general characteristics of the transfer functions are discussed. Calculated motion errors by the proposed method show good agreement with the ones calculated by Multi Pad Method, which is considered the entire table as an analysis object. Also, by the introduction of the transfer function of motion errors, which represent the relationship between the spatial frequency components of the rail form error and motion errors, motional characteristics of the porous aerostatic stage can be generalized. In detail, the influence of the spatial frequencies is analyzed quantatively, and the patterns of the insensitive frequencies which almost do not affect the linear motion error or angular motion error according to the rail length ratio and the number of the pad are verified. The relationship between the moment variation occurred inside the pads and the motion errors is also verified together.