• Korean Journal of Materials Research
• /
• v.2 no.5
• /
• pp.375-382
• /
• 1992

Molybdenum silicide films have been prepared by sputtering from a single composite MoS$i_2$ source on both P, B$F_2$respectively implanted (5${\times}10^{15}ions/cm^2$ single crystal and P implanted (5${\times}10^{15}ions/cm^2$) polycrystalline silicon substrates followed by rapid thermal annealing in the ambient of argon. The heat treatment temperatures have been varied in the range of 600-l20$0^{\circ}C$ for 20 seconds. The properties of Mo-silicide and the diffusion behaviors of dopant after the heat treatment are investigated using X-ray diffraction, scanning electron microscopy(SEM) , secondary ions mass spectrometry(SIMS), four-point probe and $\alpha-step.$ Annealing at 80$0^{\circ}C$ or higher resulted in conversion of the amorphous phase into predominantly MoS$i_2$and a lower sheet resistance. There was no significant out-diffusion of dopants from both single crystal and polycrystalline silicon substrate into molybdenum silicide layers during annealing.

• Journal of the Korean Magnetics Society
• /
• v.14 no.6
• /
• pp.236-239
• /
• 2004

We studied the specular spin valve (SSV) having the spin filter layer (SFL) in contact with the ultrathin free layer composed of Ta3/NiFe2/IrMn7/CoFel/(NOLl)/CoFe2/Cu1.8/CoFe( $t_{F}$)/Cu( $t_{SF}$ )/(NOL2)/Ta3.5 (in nm) by the magnetron sputtering system. For this antiferromagnetic I $r_{22}$M $n_{78}$-pinned spin filter specular spin valve (SFSSV) films, an optimal magnetoresistance (MR) ratio of 11.9% was obtained when both the free layer thickness ( $t_{F}$) and the SFL thickness ( $t_{SF}$ ) were 1.5 nm, and the MR ratio higher than 11% was maintained even when the $t_{F}$ was reduced to 1.0 nm. It was due to increase of specular electron by the nano-oxide layer (NOL) and of current shunting through the SFL. Moreover, the interlayer coupling field ( $H_{int}$) between free layer and pinned layer could be explained by considering the RKKY and magnetostatic coupling. The coercivity of the free layer ( $H_{cf}$ ) was significantly reduced as compared to the traditional spin valve (TSV), and was remained as low as 4 Oe when the $t_{F}$ varied from 1 nm to 4 urn. It was found that the SFL made it possible to reduce the free layer thickness and enhance the MR ratio without degrading the soft magnetic property of the free layer.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.6
• /
• pp.203-207
• /
• 2009

We have investigated the effect of ambient gases on the structural, electrical, and optical characteristics of ITO thin films intended for use as anode contacts in OLED (organic light emitting diodes) devices. These ITO thin films are deposited by radio frequency (RF) magnetron sputtering under different ambient gases (Ar, Ar+$O_2$, and Ar+$H_2$) at $300{^{\circ}C}$. In order to investigate the influences of the oxygen and hydrogen, the flow rate of oxygen and hydrogen in argon mixing gas has been changed from 0.5 sccm to 5 sccm and from 0.01 sccm to 0.25 sccm, respectively. The intensity of the (400) peak in the ITO thin films increased with increasing $O_2$, flow rate whilst the (400) peak was nearly invisible in an atmosphere of Ar+$H_2$. The electrical resistivity of the ITO thin films increased with increasing $O_2$ flow rate, whereas the electrical resistivity decreased sharply under an Ar+$H_2$ atmosphere and was nearly similar regardless of the $H_2$ flow rate. The change of electrical resistivity with changes in the ambient gas composition was mainly interpreted in terms of the charge carrier mobility rather than the charge carrier concentration. All the films showed an average transmittance of over 80% in the visible range. The OLED device was fabricated with different ITO substrates made with the configuration of ITO/$\alpha$-NPD/DPVB/$Alq_3$/LiF/Al in order to elucidate the performance of the ITO substrate. Current density and luminance of OLED devices with ITO thin films deposited in Ar+$H_2$ ambient gas is the highest among all the ITO thin films.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.734-736
• /
• 2012

Cadmium telluride (CdTe) films have been prepared on Corning 7059 glass, molybdenum (Mo), and polyimide (PI) substrates by r.f. magnetron sputtering technique. The influence of the sputter pressure on the structural and optical properties of these films was evaluated. In addition, a comparison of the properties of the films deposited on fferent substrates was performed.

• Korean Journal of Materials Research
• /
• v.34 no.1
• /
• pp.34-43
• /
• 2024

New piezoelectric and triboelectric materials for energy harvesting are being widely researched to reduce their processing cost and complexity and to improve their energy conversion efficiency. In this study, BaTiO₃ films of various thickness were deposited on Ni foams by R.F. magnetron sputtering to study the piezoelectric and triboelectric properties of the porous spongy structure materials. Then piezoelectric nanogenerators (PENGs) were prepared with spongy structured BaTiO₃ and PDMS composite. The output performance exhibited a positive dependence on the thickness of the BaTiO₃ film, pushing load, and poling. The PENG output voltage and current were 4.4 V and 0.453 ㎂ at an applied stress of 120 N when poled with a 300 kV/cm electric field. The electrical properties of the fabricated PENG were stable even after 5,000 cycles of durability testing. The triboelectric nanogenerators (TENGs) were fabricated using spongy structured BaTiO₃ and various polymer films as dielectrics and operated in a vertical contact separation mode. The maximum peak to peak voltage and current of the composite film-based triboelectric nanogenerator were 63.2 V and 6 ㎂, respectively. This study offers new insights into the design and fabrication of high output nanogenerators using spongy structured materials.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.183-183
• /
• 2009

OLED소자의 양극재료로써 현재는 산화인듐주석(ITO : indium tin oxide) 박막이 널리 이용되고 있다. 그러나 낮은 전기 비저항과 높은 투과도를 갖는 ITO 박막을 얻기 위해서는 $300^{\circ}C$ 이상의 고온에서 성막되어야 하며, 원료 물질인 인듐의 수급량 부족으로 인한 문제점과 독성, 저온증착의 어려움, 스퍼터링 시 음이온 충격에 의한 막 손상으로 저항의 증가의 문제점이 있고, 또한 유기발광소자의 투명전극으로 쓰일 경우에 유기물과의 계면 부적합성, 액정디스플레이의 투명전극으로 사용될 경우에 $400^{\circ}C$정도의 놓은 온도와 수소 플라즈마 분위기에서 장시간 노출 시 열화로 인한 광학적 특성변화가 문제가 된다. 이러한 문제점을 지닌 ITO 박막을 대체할 수 있는 물질로 산화 인듐아연(lZO) 박막이 많은 각광을 받고 있다. IZO(Indium Zinc Oxide) 박막은 저온 ($100^{\circ}C$ 이상)에서 증착이 가능하고 추가적인 열처리 없이도 가시광 영역에서 90% 이상의 광 투과도와 ${\sim}10^{-4}{\Omega}cm$ 이하의 낳은 전기 비저항을 갖는 것으로 알려져 있다. 이러한 IZO박막은 성막 후 고온의 열처리 과정이 필요 없기 때문에 폴리카보네이트와 같은 유기물 기판을 사용하여 제작 가능한 유연한 평판형 표시 소자의 제작에도 적용될 수 있다. IZO(Indium Zinc Oxide) 박막은 상온 공정에서도 우수한 전기적, 광학적, 표면 특성을 나타낼 뿐만 아니라 양극재료로써 높은 일함수를 가지고 있어 고효율의 유기 발광 소자를 구현하는데 유리한 재료라 판단된다. 본 연구에서는 TCO 박막의 면 저항과 표면 거칠기가 OLED 소자의 성능에 미치는 영향을 조사하였다. R.F Magnetron Sputtering을 이용하여 투명 전도막을 성막 형성 하였으며, 기판온도와 증착과정에서 주입되는 산소, 수소의 유랑 변화가 박막의 구조적, 전기적 특성에 어떠한 영향 미치는 것인가를 자세히 규명하였다 ITO 와 IZO박막은 챔버 내 다양한 가스 분위기(Ar, $Ar+O_2$ and $Ar+H_2$) 에서 R.F Magnetron Sputtering 방법으로 증착했다. TCO박막의 구조적인 이해를 돕기 위해서 X-ray diffraction 과 FESEM으로 분석했다. 광학적 투과도와 박막의 두께는 Ultraviolet Spectrophotometer(Varian, cary-500)와 Surface profile mersurement system으로 각각 측정하였다. 면저항, charge carrier농도, 그리고 TCO박막의 이동성과 길은 전기적특성은 Four-point probe와 Hall Effect Measurement(HMS-3000)로 각각 측정한다. TCO 박막의 표면 거칠기에 따른 OLED소자의 성능분석 측면에서는 TCO 박막의 표면 거칠기 조절을 위해 photo lithography 공정을 사용하여 TCO 박막을 에칭 하였다. 미세사이즈 패턴 마스크가 사용되고 에칭의 깊이는 에칭시간에 따라 조절한다. TCO박막의 표면 형태는 FESEM과 AFM으로 관찰하고 그리고 나서 유기메탈과 음극 전극을 연속적으로 TCO 박막위에 증착한다. 투명전극으로 사용되는 IZO기판 상용화를 위해 IZO기판 위에 $\alpha$-NPB, Alq3, LiF, Al순서로 OLED소자를 제작하였다. 전류밀도와 전압 그리고 발광과 OLED소자의 전압과 같은 전기적 특성은 Spectrometer (minolta CS-1000A) 에 의하여 I-V-L분석을 했다.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.1
• /
• pp.15-20
• /
• 2003

NiCr alloys are prepared onto poly-Si/ $SiO_2$/Si substrates to replace Pt bottom electrode with a new one for integration of high dielectric constant materials. Alloys deposited at Ni and Cr power of 40 and 40 W showed optimum properties in the composition of N $i_{1.6}$C $r_{1.0}$. The grain size of films increases with increasing deposition temperature. The films deposited at 50$0^{\circ}C$ showed a severe agglomeration due to homogeneous nucleation. The NiCr alloys from the rms roughness and resistivity data showed a thermal stability independent of increasing annealing temperature. The 80 nm thick BST films deposited onto N $i_{1.6}$C $r_{1.0}$/poly-Si showed a dielectric constant of 280 and a dissipation factor of about 5 % at 100 kHz. The leakage current density of as-deposited BST films was about 5$\times$10$^{-7}$ A/$\textrm{cm}^2$ at an applied voltage of 1 V. The NiCr alloys are possible to replace Pt bottom electrode with new one to integrate f3r high dielectric constant materials.terials.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1806-1808
• /
• 1999

The electrical and physical characteristics of MgO and Pt thin-films on Si substrate, deposited by r.f magnetron sputtering. It were analyzed with annealing condition($1000^{\circ}C$ for 120 min) by four point probe, a-step, SEM and XRD. Until $1000^{\circ}C$ of annealing temperature, MgO medium layer had the properties of improving Pt adhesion to $SiO_2$ and insulation without chemical reaction to Pt thin-films and the resistivity of Pt thin-films was improved. In the analysis of properties of Pt-RTD, TCR value had $3927ppm/^{\circ}C$ and liner in the temperature range of room temperature ${\sim}400^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.4
• /
• pp.1331-1335
• /
• 2011

We report the results of the characterization of Cu oxide thin films deposited by radio frequency (r.f.) magnetron sputtering at different annealing temperatures. The deposited Cu oxide thin films were investigated by scanning electron microscopy, spectroscopic ellipsometry, X-ray diffraction, atomic force microscopy, Xray photoelectron spectroscopy, and contact angle measurements. The thickness of the films was about 180 nm and the monoclinic CuO phase was detected. The $CuO_2$ and $Cu(OH)_2$ phases were grown as amorphous phase and the ratio of the three phases were independent on the annealing temperature. The surface of Cu oxide films changed from hydrophilic to hydrophobic as the annealing temperature increased. This phenomenon is due to the increase of the surface roughness. The direct optical band gap was also obtained and laid in the range between 2.36 and 3.06 eV.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.746-748
• /
• 1998

Thin films of vanadium pentoxide ($V_{2}O_{5}$) have been deposited by r.f. magnetron sputtering from $V_{2}O_{5}$ target in gas mixture of argon and oxygen. Crystal structure, surface morphology, surface composition and optical properties of films prepared under different substrates are characterized through XRD, SEM, AES, XPS and optical absorption measurements. The films prepared below $100^{\circ}C$ are amorphous, and those prepared above $200^{\circ}C$ are polycrystalline. Thermally Induced oxidation of films into higher oxide has been observed with increasing substrate temperature. Vanadium oxide films show two optical absorption bands indicating the presence of direct and indirect transitions.