• Journal of the Korean Vacuum Society
• /
• v.19 no.5
• /
• pp.391-396
• /
• 2010

The pn junction for solar cell was prepared on p-type Si wafer by the furnace using the $POCl_3$ and oxygen mixed precursor to research the characteristic of interface at pn junction. The sheet resistance was decreased in accordance with the increasing the diffusion process time for n-type doping on p-type Si wafer. The electron affinity at the interface in the pn junction was decreased with increasing the amount of n-type doping and the sheet resistance also decreased. Consequently, the drift current due to the generation of EHP increased because of low potential barrier. The efficiency and fill factor were increased at the solar cell with increasing the diffusion process time.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.2
• /
• pp.39-43
• /
• 2017

It was confirmed that the silicon thin films fabricated on the p-Si (100) substrates by using DIPAS (DiIsoPropylAminoSilane) and TDMA-Sb (Tris-DiMethylAminoAntimony) sources by RPCVD method were amorphous and n-type silicon. The fabricated amorphous n-type silicon films had electron carrier concentrations and electron mobilities ranged from $6.83{\times}10^{18}cm^{-3}$ to $1.27{\times}10^{19}cm^{-3}$ and from 62 to $89cm^2/V{\cdot}s$, respectively. The ideality factor of the pn junction diode fabricated on the p-Si (100) substrate was about 1.19 and the efficiency of the fabricated pn solar cell was 10.87%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1990.10a
• /
• pp.88-90
• /
• 1990

In this study, PN junction solar cell and P$\^$+/-N-N$\^$+/ BSF solar cell, using N-type(111), 10$\^$16/[atoms/cm$\^$-3/] wafer, were fabricated applying that ion implant method whose dose are 1E14, 1E15, 3E15 and its acceleration energy is 50Key, 100Key respectively. The impurity concentration of two types of front-side are 10$\^$18/[atoms/cm$\^$-3/] and back-side concentration for BSF solar cell is 10$\^$17/[atoms/cm$\^$-3/]. As a result of comparison for 2 typical types of cells out of various fabricated samples, open circuit voltage (Voc), short circuit current(Isc) of BSF solar cell are larger than those of PN solar cell by 48[%], 14[%]. Considering that the efficiency of BSF cell is 2.5[%] as well as PN solar cell's is 7.5[%], 10.0[%] of efficiency improvement effect can be obtained from BSF solar cell. Futhermore, in consequence of front-side impurity concentration change from 10$\^$17/[atoms/cm$\^$-3] to 10$\^$20/[atoms/cm$\^$-3/] alternately, the most ideal result can be expected when it is 10$\^$18/[atoms/cm$\^$-3/].

• Korean Journal of Materials Research
• /
• v.27 no.2
• /
• pp.107-112
• /
• 2017

The BCBJ (Back Contact and Back Junction) or back-lit solar cell design eliminates shading loss by placing the pn junction and metal electrode contacts all on one side that faces away from the sun. However, as the electron-hole generation sites now are located very far from the pn junction, loss by minority-carrier recombination can be a significant issue. Utilizing Medici, a 2-dimensional semiconductor device simulation tool, the interdependency between the substrate thickness and the minority-carrier recombination lifetime was studied in terms of how these factors affect the solar cell power output. Qualitatively speaking, the results indicate that a very high quality substrate with a long recombination lifetime is needed to maintain the maximum power generation. The quantitative value of the recombination lifetime of minority-carriers, i.e., electrons in p-type substrates, required in the BCBJ cell is about one order of magnitude longer than that in the front-lit cell, i.e., $5{\times}10^{-4}sec$ vs. $5{\times}10^{-5}sec$. Regardless of substrate thickness up to $150{\mu}m$, the power output in the BCBJ cell stays at nearly the maximum value of about $1.8{\times}10^{-2}W{\cdot}cm^{-2}$, or $18mW{\cdot}cm^{-2}$, as long as the recombination lifetime is $5{\times}10^{-4}s$ or longer. The output power, however, declines steeply to as low as $10mW{\cdot}cm^{-2}$ when the recombination lifetime becomes significantly shorter than $5{\times}10^{-4}sec$. Substrate thinning is found to be not as effective as in the front-lit case in stemming the decline in the output power. In view of these results, for BCBJ applications, the substrate needs to be only mono-crystalline Si of very high quality. This bars the use of poly-crystalline Si, which is gaining wider acceptance in standard front-lit solar cells.

• Journal of the Korean Vacuum Society
• /
• v.22 no.3
• /
• pp.162-167
• /
• 2013

An epitaxial layer structure for heterojunction p-InGaP/N-InAlGaP solar cell has proposed. Simulation for current density-voltage characteristics has been performed on p-InGaP/N-InAlGaP structure and the simulation results were compared with p-InGaP/p-GaAs/N-InAlGaP structure and homogeneous InGaP pn junction structure. The simulation result showed that the maximum output power and fill factor have greatly increased by replacing n-InGaP with N-InAlGaP. The thicknesses of p-InGaP and n-InAlGaP were optimized for the epitaxial layer structure of p-InGaP/N-InAlGaP.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.12
• /
• pp.9-12
• /
• 2005

This paper describes the feasibility of the electrostatic cell using carrier injection in SCR(space charge region) of PN junction. It compares the principle of the electrostatic cell's operation with the solar cell's. According to the experiment and calculation of this paper, when the cross section area of the device is $0.0001cm^2$, the device current becomes 0.15mA which is practically high enough. This paper proposes that the electrostatic cell can be used as a physical battery.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.196-197
• /
• 2011

실리콘 태양전지의 pn 접합 계면특성을 조사하기 위해서 p형 실리콘 기판 위에 전기로를 이용한 $POCl_3$ 공정을 통하여 n형의 불순물을 주입하여 pn접합을 만들었다. n형 불순물의 확산되어 들어가는 공정시간이 길고 공정온도가 높을수록 면저항은 줄어들었다. n형 불순물의 주입이 많아질수록 pn 접합 계면에서의 전자친화도가 줄어들면서 면저항은 감소되었다고 할 수 있다. n형 반도체의 페르미레벨이 높아지면서 공핍층도 생기지만 n형 불순물이 많아지면서 공핍층의 폭은 점점 좁아지고 쇼키 장벽의 높이도 낮아지면서 자유전자와 홀 쌍의 이동이 쉽게 이루어지게 되었다. n형의 불순물 확산공정시간이 긴 태양전지 셀에서 F.F. 계수가 높게 나타났으며, 효율도 높게 나타났다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.15 no.3
• /
• pp.18-23
• /
• 1978

In order to improve the efficiency of Cu2-xS-CdS PN junction type solar cell, a method of reducing the series resiatance is considered. In the fabrication of the thin film of Cu2-xS, what has the largest value of conductivity is fabricated at 250 $^{\circ}C$. The thin film of CdS which has beer fabricated at the temperature 250-30$0^{\circ}C$ of the substrate and 800-85$0^{\circ}C$ of evaporating material has the largest value of conductivity and also fairly good photoelectric characteristics. Therefore, the evaporated thin aim type CdS solar cell has been fabricated at the temperature 25$0^{\circ}C$ of the substrate and 800-85$0^{\circ}C$ of the evaporating material, and its efficiency is measured to he 6%.

• Journal of the Korean Vacuum Society
• /
• v.20 no.3
• /
• pp.189-194
• /
• 2011

Si-cell was prepared with various types owing to the etching times textured by the KOH etching solution. The pn junction for solar cell was prepared on p-type Si wafer by the furnace using the $POCl_3$ and oxygen mixed precursor, and the metalization was done using by the Al back electrode and Ag front electrode. Textured Si surface was etched by the pyramid formation. The efficiency and the fill factor was increased in the Si-cell with a large size of pyramids, because of the series resistances decrease depending on the increasing of the photon absorbance. Increasing of the absorbance occurred the induction of the short current and open voltage, and then the efficiency was increased.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.3
• /
• pp.46-51
• /
• 2023

We investigated the MoS₂ thin film layer by thermolytic deposition and applied it to the silicon solar cells. MoS₂ thin films were made by two methods of dipping and spin coating of (NH₄)₂MoS₄ precursor solution. We implemented two types of substrates of microtextured and nano-microtextured 6-in. Si pn junction wafers. The fabricated MoS₂ thin film layer was analyzed, and solar cells were fabricated by applying the standard silicon solar cell process. The MoS₂ thin film layer of sulfur-deficient form was deposited on the n-type emitter layer, and electrons, which are minority carriers, were well transported at the interface and exhibited photovoltaic solar cell characteristics. The cell efficiencies were achieved at 5% for microtextured wafers and 2.56% for nano-microtextured wafers.