• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.5
• /
• pp.385-390
• /
• 2002

To clarify the hydraulic characteristics of ice slurry which made from 6.5% ethylene glycol-water solution flowing through circular pipes of small diameter, experimental studies were performed. The flow pattern was observed and the pressure drop was measured in acrylic pipes with inner diameter of 24 mm. The results of flow visualization revealed that ice particles flowed along the top of pipes in the ranges of small ice fraction and low flow rate, while Ice particles diffused into the whole region of pipes flowed like a homogeneous flow for high flow rate and high ice fraction. An increase in frictional pressure drop was measured as the ice fraction increased in all pipes and unstable flow was observed for up-ward vertical pipe.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.4
• /
• pp.325-331
• /
• 2003

This paper described the characteristics of the exhaust pressure and proposed the assistant device for detection of misfired cylinder. Misfire, one of abnormal combustion, affects a bad influence of the 3-way catalyst and emits unburned hydrocarbon. Therefore, to prevent these unusual phenomena and eliminate the factor of the environmental pollution, early detection and correction of the misfired cylinder play a very important role. The configuration of assistant device was changed by length and diameter of pipe and analyzed with the install position on the exhaust system. Experimental results showed that the configuration of assistant device is not affected more than length and diameter of pipe and the assistant device is be effective in the detection of misfired cylinder on the gasoline engine.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.43-52
• /
• 2000

In this study, a simulation program was developed, which could simulate a fuel injection system for low-speed marine diesel engine. The fuel injection system was divided into fuel injection pump, high pressure pipe and fuel injection valve. The unsteady flow in the high pressure injection pipe was analyzed by the method of characteristics, considering cavitation and variation of fuel density and bulk modulus. It was confirmed that the simulation results were good agree with experimental results of injection pressure and quantity at the high pressure distributor in fuel injection system for the training ship "M/V Hannara". And the effects of the atomizer hole diameter, maximum needle lift, plunger diameter and nozzle opening pressure were also investigated with simulating results.g results.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.2
• /
• pp.251-256
• /
• 2017

This study developed an image processing system for detecting damages on underground spiral PVC pipes. The detection method is simple-identifying damaged areas by measuring circularity along the pipeline. This uses the assumption that damage parts will not make a circular shape. Conventional devices check the circular shape of the pipe along the pipeline by measuring the angles between 6 spring-connected legs on the device. The conventional device, however, requires the insertion of 3 different wires (electrical, communication, and camera lines) along with a guide wire for pulling the device. The developed system presented here has simplified this system, requiring only a camera line while maintaining reasonable accuracy in damage detection.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.80-86
• /
• 2002

A fuel injection system has an important role in the performance and emission gas in a diesel engine. In this paper, an experimental study has been performed to verify the effect of the performance and the emission gas with the factors such as diameters of an injection nozzle hole, diameters of an injection pipe, and injection timing in the fuel injection system. We have obtained the results that the fuel consumption ratio is reduced and NOx concentration is increased as the smaller diameter of injection nozz1e hole, the smaller diameter of injection pipe, and more advanced injection timing. They show that optimizing the factors of fuel injection system is significant to enhance the performance of the engine system and consumption ratio of fuel, smoke, and NOx.

• Ocean Systems Engineering
• /
• v.1 no.1
• /
• pp.59-72
• /
• 2011

The objective of this work is to investigate the possibility of using the longitudinal strain on the surface of a pipe to determine the inception of dangerous free spanning. The long term objective is to develop an online monitoring technique to detect the development of dangerous free spanning in subsea pipelines. This work involves experimental study as well as finite element modeling. In the experiments, the strains at four points on a cross section of a pipeline inside the free span zone are measured. Pipes with different boundary conditions and different diameter to length ratios were tested. The pipe is treated as a simple beam with fixed-fixed or simply supported boundary conditions. The variation of the strains as a function of the diameter to length ratio gives a pointer to the inception of dangerous free spanning. The finite element results agree qualitatively with the experiments. The quantitative discrepancy is a result of the difficulty to replicate the exact boundary conditions that is used by the finite element program.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.17 no.2
• /
• pp.37-44
• /
• 2009

It is well known that a refrigerant-induced noise is caused by two-phase flow in the indoor unit of a heat pump air-conditioner. Especially when the flow pattern in a pipe is intermittent flow, the irregular noise occurs frequently. But it is very difficult to avoid this kind of the noise for the application of air-conditioner. Therefore, in this research, the flow patterns at two-phase flow state in a pipe of the indoor unit for the air-conditioner are researched using cycle simulator at typical cycle conditions. In order to find the relationship between refrigerant-induced noise and flow pattern, the noise patterns are investigated with respect to the estimated flow pattern from the various flow pattern maps. Base on the estimations of the flow patterns by those maps, the refrigerant-induced noise is evaluated as decreasing tube diameter, which can transit the flow pattern from slug to annular flow.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.81-86
• /
• 2013

This article deals with the manufacturing and performance evaluation on the specimen pipes which have large size diameter and thin thickness. This specimen is for LOX main pipe of KSLV-II propulsion feeding system. The material of specimen is alloy 21-6-9. Alloy 21-6-9 has higher strength and better weldability rather than STS-300 class pipes. We found that the specimen using alloy 21-6-9 satisfied the requirement by pressurization tests.

• Journal of Korea Water Resources Association
• /
• v.32 no.4
• /
• pp.469-478
• /
• 1999

Explicit equations of minimum velocity, energy slope and pipe diameter are developed to ensure the cleaning of sewerage pipes. The equations of power form are employed for the estimation of critical shear stress of sediment particles and the friction factor of commercial pipes. They are all based on the existing laboratory data. Several cases are tested to check the values suggested in the manual, using the equations developed in the present study.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.12
• /
• pp.1107-1116
• /
• 2004

In this paper, the effects of diverse parameters on the operation of loop heat pipe (LHP), such as particle diameter of sintered porous wick, wick porosity, vapor line diameter, thickness of wick and heating capacity were investigated by a theoretical analysis. A LHP has a wick only in its evaporator for the circulation of working fluid, and utilizes a porous wick structure of which pore size is very small to obtain a large capillary force. The working fluid is water and the material of sintered porous wick is copper. For these different parameters, capillary pressure, pressure drop in wick, pressure drops and temperature distribution were analyzed by a theoretical design method of LHP.