• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.5
• /
• pp.141-146
• /
• 2015

This study was carried out to elucidate the partial substitutability of SB latex with environmental-friendly coating binders for coated paper. Starch-based biobinder, ethylene vinyl acetate and acryl-based binder were evaluated for this purpose. Several combinations of above binders were applied to top layer coating, and properties of coating colors and printability were evaluated. When 20% and 30% of SB latex were substituted by acryl-based synthetic binder, ethylene vinyl acetate and biobinder, the brightness, whiteness and opacity of coated paper were similar to those obtained from SB latex. Ink set and stiffness of coated paper manufactured through 20% and 30% substitution of SB latex by biobinder and EVAc were improved, but dry- and wet-pick strength were decreased. The research works on the improvement of dry- and we-pick strength, mechanical stability and rheological properties at high shear condition should be continued for the commercial application of biobinder, EVAc and acryl-based binder.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.2
• /
• pp.105-109
• /
• 2020

Today's placement machines can pick and place thousands of components per hour with a very high degree of accuracy. The packaged semiconductor chips are inserted into a carrier at regular intervals, covered with a tape to protect the chips from external impact, and supplied in a roll form. These packaging processes also progress rapidly in a consistent direction, affecting the peelback strength between the cover tape and carrier depending on the main process conditions. In this paper, we analyzed the main process variables that affect peelback strength in the reel tape packaging process for packaging semiconductor chips. The main effects and interactions were analyzed. The peelback strength range required in the packaging process was set as the nominal the best characteristics, and the optimum process condition satisfying this was derived.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.1 s.113
• /
• pp.34-44
• /
• 2006

A new composition of paper coating adhesives was prepared by using a nano-filler of an organically-modified montmorillonite (O-MMT). The new O-MMT coating adhesives were applied to the paper, and the properties of coated papers including surface morphology, optical and physical properties, and printing properties were investigated. The use of O-MMT improved the mechanical properties, such as folding endurance, tearing strength, and tensile strength, while the surface smoothness decreased. It decreased especially when the dosage was high enough, approximately above 6 parts. The printing properties such as wet- and dry-pick were enhanced with addition of O-MMT.

• Fashion & Textile Research Journal
• /
• v.3 no.4
• /
• pp.362-366
• /
• 2001

We studied on the softness properties of polyester fabric by vapor type ozone processing using ozone's strong oxidation instead of 25% NaOH chemical treatment. When vapor type ozone processing was directly treated to fabrics retaining water to 40% pick up ratio, high concentration ozone was generated oxidation of 3~4% approximately in polyester fabrics and finally its softness improved. The fabric's softness effect was improved because vapor type ozone generated the highest decomposition to oxidation of surface and inter molecules. The experiment revealed that fabric's softness was improved by change of the time of vapor type ozone processing. However, tensile strength and elongation were reduced by increase in time, 60 minute was assumed as the most optimized time to minimize the reduction of fabric's tensile strength and elongation as well as maximizing the fabric's softness.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.774-780
• /
• 1999

The study of bond behavior between concrete and rebar has been performed for a long time. On this study, we tried to analysed variation of bond behaviors quantitatively with varying the strength of concrete. Bond stress which observed below the neutral surface of beam and at connecting part of beam and column is affected by various bond parameters. Resistance of deformed bars which embedded in concrete to the pullout force is divided 1) chemical adhesive force 2) frictional force 3) mechanical resistance of ribs to the concrete and these horizontal components of resistance is being bond strength. We selected the most common and typical variable which is concrete strength among various variables. So we used two kinds of concrete strength like as 25MPa(NSC) and 65MPa(HSC). Tension Test was performed to verify how bond behavior varied with two kinds of concrete strength. Concentration of bond stress was observed at load-end commonly in Tension Test of the initial load stage. At this stage stress distribution was almost coincident at each strength. As tension load added, this stress distribution had difference gradually and movement of pick point of bond stress to free-end and central section was observed. This tendency was observed at first and moving speed was more fast in NSC. At the preceeding result the reason of this phenomenon is considered to discretion of chemical adhesion and local failure of concrete around rebar in load-end direction. Especially, when concrete strength was increased 2.6 times in tension test, ultimate bond strength was increased 1.45 times. In most recent used building codes, bond strength is proportioned to sqare root of concrete compressive strength but comparison of normalized ultimate bond strength was considered that the higher concrete strength is, the lower safety factor of bond strength is in each strength if we use existing building codes. In Tension Test, in case of initial tensile force state, steel tensile stress of central cross section is not different greatly at each strength but tensile force increasing, that of central cross section in NSC was increased remarkably. Namely, tensile force which was shared in concrete in HSC was far greater than that of concrete in NSC at central section.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.27 no.4
• /
• pp.171-180
• /
• 2023

This study proposed a seismic reinforcement of RC columns with non-seismic details, a fiber reinforcement method of aramid sheets and MLCP (high elasticity aromatic polyester fiber material) with different characteristics, and 4 full-size column specimens and conducted experiments. The results show that a non-seismic specimen (RC-Orig) rapidly lost its load-bearing capacity after reaching the maximum load, and shear failure occurred. The RC column reinforced with three types of aramid did not show an apparent increase in strength compared to the unreinforced specimen but showed a ductile behavior supporting the load while receiving a lateral displacement at least 1.57 to 1.95 times higher than the unreinforced specimen. The fracture mode of the specimen, according to the application of lateral load, also changed from shear to ductile fracture through aramid-based reinforcement. In addition, when examining the energy dissipation ability of the reinforced specimens, a ductile behavior dissipating seismic energy performed 4 times greater and more stably than the existing specimens.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.1
• /
• pp.10-16
• /
• 2015

Bio-binder is well known as a promising alternative binder for SB latex because it is eco-friendly and inexpensive, compared to synthetic latex. SB latex in top coating color was substituted with starch-based bio-binder to investigate its effects on the coating color and its coated paper properties. Bio-binder contributed to the increase of coating color viscosity, and the improvement of water retention. Most optical properties except opacity were deteriorated by the increase of bio-binder dosage. It was also found that the increase of bio-binder substitution in top coating color brought about the increase of roughness, and decrease of coated paper gloss, print gloss, dry and wet pick strength. However the stiffness and the ink set-off of the bio-binder coated paper were improved. Overall, mostly adverse effects of bio-binder on the properties of coating color and its paper were observed. Therefore, it is not recommended to use bio-binder as top coating color.

• Journal of the Korean Society for Precision Engineering
• /
• v.34 no.1
• /
• pp.65-72
• /
• 2017

The goal of this paper is to investigate the effects of out-of-plane deposition angle on product characteristics of a UV photo-curing process. Specimens are manufactured from a commercialized UV photo-curing machine, the NOBEL V1.0. The influence of the out-of-plane deposition angle of the specimen on surface characteristics, including morphology of the sloped surface, pick-to-pick distance of convex region, and roughness of the sloped surface, is examined via the observation of the sloped surface. In addition, the influence of the radius of curvature of the specimen on the surface roughness of the sloped surface is evaluated. The effects of the out-of-plane deposition angle on impact strength of specimens are investigated via Izod impact experiments. Finally, we discuss the influence of the out-of-plane deposition angle on failure characteristics of specimens for impact loads.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.2 s.120
• /
• pp.25-30
• /
• 2007

Recently the use of web offset printing has been increasing, which can provide high print speed, mass production, and high print quality. However, high speed web offset printing has frequently undergone a blistering problem when the printed paper passes through hot air dryers. Blistering occurs in the middle of the base paper or in the coating layer. This paper focused on the blistering occurring in the base paper. In order to elucidate the effect of pigment ratio on blistering, 6 types of coating color were prepared with varying GCC/clay ratios and printability and blistering were investigated focusing on structure changes in the coating layer. When the clay content in the coating layer was increased, surface roughness and surface strength were decreased and paper gloss was increased. In addition, it was found that the coating layer structure with high clay content, which contains lots of discontinuous pores, hindered water vapors to penetrate out and, as a result, blistering occurred.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.4
• /
• pp.16-21
• /
• 2002

It was observed that drying temperature and curing time in the paper coating process as well as Tg of the latex used as a binder, greatly affected the properties of the coated paper such as roughness, paper and print gloss, K & N ink drop, and ink set-off. The higher drying temperature induced faster water evaporation and change in binding density, which caused an increase in paper roughness, ink gloss and ink set-off, but decrease in paper gloss and K & N ink drop. The increased curing time promoted latex filming and redistribution of the binder in coating layer. This increased pick strength and ink gloss, but decreased ink trapping. Finally, the higher Tg of the latex showed the wider changing range of these properties.