• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.3
• /
• pp.380-383
• /
• 2012

Small permanent magnet generator can be used not only as an emergency power source but also an exciting power source of generator for small generating systems because it does not need the external exciting power source. Especially the air-gap flux density of the buried PM synchronous generator can be increased more than that of the permanent magnet. In this study, the analysis of the small buried type PM synchronous generator is performed. From the phasor diagram considering armature resistance for exact analysis, analytic equations are induced and the efficiency, developed voltage, load current are calculated. The experimental results are compared with the calculated results for the appropriateness.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.1
• /
• pp.49-56
• /
• 2009

This paper shows the characteristic analysis of single-phase line start permanent magnet (LSPM) motors considering the overhang structure. To achieve the low-cost design of an LSPM motor, the overhang structure is adapted for the rotor with a constraint of a fixed magnet volume. To obtain the dynamic and steady performance of the motor, the circuit parameters are extracted using the 3D-static FEM(Finite Element Method) and the d-q equivalent circuit is used. The performance of the model with overhang is compared with the conventional model without overhang on the condition that both models have a fixed volume for the permanent magnet.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1002-1006
• /
• 2015

In this paper, design and analysis of permanent magnet synchronous generator for ocean thermal energy conversion (OTEC) considering magnetically coupled turbine-rotor system is discussed. In particular, the rotor dynamics considering bearing span and journal shaft diameter is highlighted. The two topologies of permanent magnet synchronous generator with magnetic coupling are employed for comparison of computed rotor dynamics and generating characteristics. The analysis results show that the critical speed of the turbine-rotor system is higher when the rotor is coupled by magnetically coupling. Finally, the experimental results confirmed the validity of the proposed design and analysis scheme and successful development.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.727-728
• /
• 2008

This paper deals with characteristic analysis of permanent magnet synchronous motor with full-ring magnet. The modeling of magnetic circuit is performed analytically. And then, analytical solution for open-circuit field distribution due to permanent magnet, back-EMF and torque are derived in terms of magnetic vector potential and two-dimensional polar coordinate system. The analytical results are validated extensively by finite element analyses. Finally, we performed experiments of permanent magnet synchronous motor with full-ring magnet.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.862-863
• /
• 2015

This paper presents an improved estimation procedure for the contribution to no-load flux linkage created by the permanent magnet (PM) in interior permanent magnet synchronous machines. In the proposed method, the saturation effect in stator and rotor cores are taken into account by utilizing the frozen permeability method (FPM). This improved procedure can evaluate the contribution for each local element in the PM to the no-load flux linkage. According to the analysis results, an effective PM topology optimal design can be carried out to achieve high utilization ratio of PM in the machine. In order to determine the threshold of the low contribution of PM for removing, one multi-objective optimization model is proposed. Based on the optimal threshold, the final optimal topology design of PM can be achieved.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.828-831
• /
• 2003

This paper presents a novel design technique and characteristic analysis of Magnet for dual air-gap axial-flux type permanent-magnet synchronous generator. The process of magnet design is applied to the motor design and steady state analysis considering output voltage waveforms and magnetic flux waveforms. Design and construction of an axial-flux permanent-magnet generator with power output at 60 [Hz], 300[r/min] is introduced. Finite-element (FE) method is applied to analyze magnet shape characteristics. The results of FE analysis show generator is feasible for use with dual air-gap axial-flux permanent- magnet synchronous generator.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.9 no.3
• /
• pp.129-134
• /
• 1989

This experiment was conducted to evaluate the effect of cutting frequency and nitrogen fertilization on th change of vegetation and the yield of dry matter on the different mixture combination of permanent pasture. 1. DM yield was increased as the increasing Arrhenatherum elntius but was decreased as the increasing Tkisetum fkavescens. 2. DM yield was unaffectdd by the different mixture combination of permanent pasture eventually. 3. In case of cutting frequency, 2-cutting showed higher DM yield than that of 3-cutting, and N-fertilization level showed significant increase in DM yield as the increasing N-level, especially 2-cutting block of N-3 showed the highest yield and 3-cutting block of N-l showed the lowest yield. 4. Mixture combination, N-level and cutting frequency did not show significant changes in DM yield of permanent pasture eventually.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.3 no.1
• /
• pp.7-11
• /
• 1976

The author measured the degree of development and the eruption pattern of first permanent molars with orthopantomography in 553 Korean children(male; 302, female; 251) from 4 to 9 years old. The orthopantomographs were obtained from dept. of pedodontics, college of dentistry, Seoul National University. The results of the studies were as follows: 1. Upper first permanent molars were erupted with distal inclination of about 30 degrees in the early stage and they gradually moved in the mesial direction by bodily movement of the tooth to be in contact with the disto-proximal surface of primary secondary molars in the late stage. 2. Lower first permanent molars were erupted with mesial inclination in the early stage and moved mesially by tipping movement of the tooth to be in contact with the disto proximal surface of the second primary molars in the late stage. 3. The eruptive forces were considered to be main etiologic factors of space closure after the premature loss of primary molars.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.4
• /
• pp.490-495
• /
• 2006

In this research, the design procedure and the design method of a single-phase line-start permanent magnet motor (LSPM) are proposed. In the design procedure, the permanent magnet is designed first and the windings and capacitors are designed later. As well, the points of design of each design parameter are explained. In the design of the single-phase LSPM, the equivalent circuit method is combined with the finite element method (FEM) because it has a shorter analysis time than FEM. The 400 watts single-phase LSPM is designed and manufactured. The characteristics of the manufactured single-phase LSPM are analyzed and experimented. From the analysis result and the experiment result, it is verified that the design procedure and the design method of the single-phase LSPM is valid.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.11
• /
• pp.541-547
• /
• 2003

Speed and torque controls of permanent magnet synchronous motors are usually attained by the application of position and speed sensors. However, speed and position sensors require the additional mounting space, reduce the reliability in harsh environments and increase the cost of a motor. Therefore, many studies have been peformed for the elimination of speed and position sensors. This paper investigates a novel speed sensorless control of a permanent magnet synchronous motor. The proposed control strategy is based on the MRAS(Model Reference Adaptive System) using the state observer model with the current error feedback and the magnet flux model as two models for the back-emf estimation. The proposed algorithm is verified through the simulation and experiment.