• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.10
• /
• pp.32-38
• /
• 2003

This works reports the measurement and analysis results on the hot electron induced device degradation in Gate-All-Around SOI MOSFET's, which were fabricated using commercially available SIMOX material. It is observed that the worst-case condition of the device degradation in nMOSFETs is $V_{GS}$ = $V_{TH}$ due to the higher impact ionization rate when the parasitic bipolar transistor action is activated. It is confirmed that the device degradation is caused by the interface state generation from the extracted degradation rate and the dynamic transconductance measurement. The drain current degradation with the stress gate voltages shows that the device degradation of pMOSFETs is dominantly governed by the trapping of hot electrons, which are generated in drain avalanche hot carrier phenomena.r phenomena.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.6
• /
• pp.601-607
• /
• 2015

A set of novel silicon controlled rectifier (SCR) devices' characteristics have been analyzed and verified under the electrostatic discharge (ESD) stress. A ring-shaped diffusion was added to their anode or cathode in order to improve the holding voltage (Vh) of SCR structure by creating new current discharging path and decreasing the emitter injection efficiency (${\gamma}$) of parasitic Bipolar Junction Transistor (BJT). ESD current density distribution imitated by 2-dimensional (2D) TCAD simulation demonstrated that an additional current path exists in the proposed SCR. All the related devices were investigated and characterized based on transmission line pulse (TLP) test system in a standard $0.5-{\mu}m$ 24 V CDMOS process. The proposed SCR devices with ring-shaped anode (RASCR) and ring-shaped cathode (RCSCR) own higher Vh than that of Simple SCR (S_SCR). Especially, the Vh of RCSCR has been raised above 33 V. What's more, their holding current is kept over 800 mA, which makes it possible to design power clamp with SCR structure for on chip ESD protection and keep the protected chip away from latch-up risk.

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.786-797
• /
• 2016

This paper describes the design and development of a novel semiconductor-based solid-state switch for damped oscillating voltage test system. The proposed switch is configured as two identical series-connected switch stacks, each of which comprising 10 series-connected IGBT function units. Each unit consists of one IGBT, a gate driver, and an auxiliary voltage sharing circuit. A single switch stack can block 20 kV-rated high voltage, and two stacks in series are proven applicable to 30 kV-rated high voltage. The turn-on speed of the switch is approximately 250 ns. A flyback topology-based power supply system with a front-end power factor correction is built for the drive circuit by loosely inductively coupling each unit with a ferrite core to the primary side of a power generator to obtain the advantages of galvanic isolation and compact size. After the simulation, measurement, and estimation of the parasitic effect on the gate driver, a prototype is assembled and tested under different operating regimes. Experimental results are presented to demonstrate the performance of the developed prototype.

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.520-523
• /
• 2022

In this paper, an ESD protection device with a simpler structure than the existing ESD protection device is proposed. The proposed new structure operates an additional NPN parasitic bipolar transistor by adding an N+ diffusion region and connecting it to the bridge region, thereby lowering the current gain. As a result, it was confirmed that the proposed ESD protection device has a trigger voltage of 10.8V and a holding voltage of 6.1V. It is expected to have reliability for 5V applications and is expected to have high tolerance characteristics.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.5
• /
• pp.16-21
• /
• 2012

For CMOS based bipolar junction transistor (BJT), a novel BJT structure which has higher matching property than conventional BJT structure was proposed and analyzed. The proposed structure shows a slight decrease of collector current density, $J_C$ about 0.361% and an increase of current gain, ${\beta}$ about 0.166% compared with the conventional structure. However, the proposed structure shows a decrease of area about 10% the improvement of matching characteristics of collector current ($A_{IC}$) and current gain ($A_{\beta}$) about 45.74% and 38.73% respectively. The improved matching characteristic of proposed structure is believed to be mainly due to the decreased distance between two emitters of pair BJTs, which results in the decreased effect of deep n-well of which resistance has the higher standard deviation than the other resistances.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1156-1161
• /
• 2020

In this paper, we propose a new ESD protection circuit with improved electrical characteristics through structural changes of the existing one-way SCR. The proposed ESD protection circuit has high holding voltage characteristics due to the inserted N+ floating and P+ floating regions, and thus the latch-up immunity characteristics are improved. In addition, structural change enables ESD discharge in four types of Zapping mode (PD, PS, ND, NS), and has superior area efficiency than unidirectional SCR. In addition, the P+ floating and N+ floating lengths corresponding to the base length of the parasitic bipolar transistor, and the distance between P+ floating and N+ floating were designated as design variables, and the high holding voltage was verified through Synopsys' TCAD Simulator.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.415-421
• /
• 2021

This study analyzed the effect on the cooling performance of the channel shape of a heat sink for an insulated gate bipolar transistor (IGBT). A serpentine channel was used for this analysis, and the parameter for the analysis was the number of curves. The analysis was conducted using computational fluid dynamics with the commercial software ANSYS fluent. One curve in the channel improved the heat dissipation performance of the heat sink by up to 8% compared to a straight-channel heat sink. However, two curves in the channel could not improve the heat discharge performance further. Instead, the two curves caused a higher pressure drop, which induces parasitic loss for the pumping of coolant. The pressure drop of the two-curve channel case was 2.48-2.55 times larger than that of a one-curve channel. This higher pressure drop decreased the heat discharge efficiency of the heat sink with two curves. The discharge heat per unit pressure drop was calculated, and the result of the straight heat sink was highest among the analyzed cases. This means that the heat discharge efficiency of the straight heat sink is the highest.