• 마이크로전자및패키징학회지
• /
• 제14권3호
• /
• pp.57-64
• /
• 2007

Si 칩에 박막히터를 형성하고 이에 전류를 인가하여 LCD (liquid crystal display) 패널의 유리기판은 가열하지 않으면서 Si 칩만을 선택적으로 가열함으로써 Si 칩을 LCD 패널의 유리기판에 실장 하는 새로운 COG 공정기술을 연구하였다. $5\;mm{\times}5\;mm$ 크기의 Si 칩에 마그네트론 스퍼터링법으로 폭 $150\;{\mu}m$,두께 $0.8\;{\mu}m$, 전체 길이 12.15 mm의 정방형 Cu 박막히터를 형성하였으며, 이에 0.9A의 전류를 60초 동안 인가하여 Si칩의 Sn-3.5Ag 솔더범프를 리플로우 시킴으로써 Si 칩을 유리기판에 COG 본딩하는 것이 가능하였다.

• 한국농공학회논문집
• /
• 제59권5호
• /
• pp.73-81
• /
• 2017

The improved movable weir supplements the advantages and disadvantages of the rubber weir and the conduction gate. It consists of a stainless steel gate, air bags, and a steel clamping plate. The stainless steel gate is the main body of the weir, and the inflatable rubber sheet serves to support the steel gate. The steel clamping plate is typically in direct continuous contact with water, but this leads to corrosion issues that can reduce the life of the entire movable weir. In this study, a panel-type glass-fiber-reinforced polymer (GFRP) clamping plate was designed and fabricated. The test results showed that the flexural load of the panel-type GFRP composite clamping plate was over twice that of the wings type GFRP clamping plate. The lowest moisture absorption value was obtained upon exposure to tap water, and exposure to other solutions showed similar values. Additionally, flexural load testing after exposure to an accelerated environment found the lowest residual loads of 80.51 % and 78.50 % at 50 and 100 days, respectively, for exposure to a $CaCl_2$ solution, while exposure to other environments showed residual failure loads of over 80 % at both 50 and 100 days.

• 반도체디스플레이기술학회지
• /
• 제12권2호
• /
• pp.13-17
• /
• 2013

In lighting system where several large-area organic light-emitting diode (OLED) lighting panels are involved, panel aging may appear differently from each other, resulting in a falling-off in lighting quality. To achieve uniform light output across large-area OLED lighting panels, we have employed an optical feedback circuit. Light output from each OLED panel is monitored by the optical feedback circuit that consists of a photodiode, I-V converter, 10-bit analogdigital converter (ADC), and comparator. A photodiode generates current by detecting OLED light from one side of the glass substrate (i.e., edge emission). Namely, the target luminance from the emission area (bottom emission) of OLED panels is monitored by current generated from the photodiode mounted on a glass edge. To this end, we need to establish a mapping table between the ADC value and the luminance of bottom emission. The reference ADC value corresponds to the target luminance of OLED panels. If the ADC value is lower or higher than the reference one (i.e., when the luminance of OLED panel is lower or higher than its target luminance), a micro controller unit (MCU) adjusts the pulse width modulation (PWM) used for the control of the power supplied to OLED panels in such a way that the ADC value obtained from optical feedback is the same as the reference one. As such, the target luminance of each individual OLED panel is unchanged. With the optical feedback circuit included in the lighting system, we have observed only 2% difference in relative intensity of neighboring OLED panels.

• 마이크로전자및패키징학회지
• /
• 제25권4호
• /
• pp.41-45
• /
• 2018

패널 레벨 패키지(Panel Level Package)에서 공정 단계별로 발생하는 휨(warpage)에 대해 유한요소법을 이용하여 전산모사를 진행하였다. $5{\times}5mm^2$ 크기의 실리콘 칩이 총 221개가 포함된 $122.4{\times}93.6mm^2$ 크기의 패널에 대해서 (1) EMC 몰딩, (2) detach core 부착, (3) 가열, (4) 캐리어 분리, (5) 냉각의 5 단계에 대해서 해석을 수행하였으며, 캐리어와 detach core 소재로 유리와 FR4의 조합이 휨 현상에 미치는 영향을 조사하였다. 캐리어 및 detach core의 소재에 따라 공정 단계별로 휨의 경향이 다르게 나타나고 있으나, 최종적으로는 유리를 캐리어로 사용하는 경우에 detach core의 소재와 관계없이 FR4 캐리어에 비해 낮은 휨 값을 나타내었으며 유리 캐리어와 유리 detach core의 조합에서 가장 낮은 휨 값이 관찰되었다.

• 한국전기전자재료학회논문지
• /
• 제26권12호
• /
• pp.858-862
• /
• 2013

The front electrode should be used to make solar cell panel so as to collect electron. The front electrode is used by paste type, printed on the Si-solar cell wafer and sintered at about $800^{\circ}C$. The paste is composed Ag powder and glass frit which make the ohmic contact between Ag electrode and n-type semiconductor layer. From the previous study, the Ag electrodes which used two commercial glass frit of Bi-system were so different on the interface resistance. The main composition of them was Bi-Zn-B-Si-O and few additives added in one of them. In this study, glass frit was made with the ratio of $Bi_2O_3$ and ZnO on the main composition, and then paste using glass frit was prepared respectively. And, also, the paste using the glass frit added oxide additives were prepared. The change of interface resistance was not large with the ratio of $Bi_2O_3$ and ZnO. In the case of G6 glass frit, 78 wt% $Bi_2O_3$ addition, the interface resistance was $190{\Omega}$ and most low. In the glass frit added oxide, the case of Ca increased over 10 times than it of G6 glass frit on the interface resistance. It was thaught that after sintering, Ca added glass frit was not flowed to the interface between Ag electrode and wafer but was in the Ag electrode.

• 한국세라믹학회지
• /
• 제52권2호
• /
• pp.103-107
• /
• 2015

The effective glass frit composition used to absorb laser energy and to seal commercial dye-sensitized solar cell panel substrates has been previously developed using $V_2O_5-TeO_2$-based glass with 10 wt% ${\beta}$-eucryptite as a CTE controlling filler. The optimum sealing conditions are provided using a 3 mm beam, a laser power of 40 watt, a scan speed of 300 mm/s, and 200 irradiation cycles. In this study, the feasibility of the developed glass frit is investigated in terms of the sealing strength and chemical durability against the commercial iodide/triiodide electrolyte solution and fluorine-doped tin oxide (FTO) electrode in order to increase the solar cell lifetime. The sealing strength of the laser-sealed $V_2O_5-TeO_2$-based glass frit is $20.5{\pm}1.7MPa$, which is higher than those of thermally sealed glass frit and other reported glass frit. Furthermore, the developed glass frit is chemically stable against electrolyte solutions. The glass frit constituents are not leached out from the glass after soaking in the electrolyte solution for up to three months. During the laser sealing, the glass frit does not react with the FTO electrode; thus, the resistivity of the FTO electrode beneath the laser-sealed area remains the same.

• Design & Manufacturing
• /
• 제11권1호
• /
• pp.1-6
• /
• 2017

In these days, due to generalization of using smart mobile phone and wearable device such as smart watch, demand of Cover-glass and touch screen panel for protecting display increases. With increasing the demand of Cover-glass, slimming technique is promising for weight lightening, zero bezel. Cover-glass produced by this technique is required to decreasing thickness with increase strength. In the Cover-glass manufacturing process, mechanical processing and chemical processing has improve in the strength. Generally, Diamond electrodeposition wheel is used in mechanical process. Reinforced glass with the characteristics of the brittle and high hardness was manufactured by using a diamond electrodeposition wheel. At this time, Because of surface of the tool present non-uniform distribution of diamond particle, it has generate Loading of wheel and it has been decrease life of grinding tool, efficiency of grinding, quality and shape accuracy of workpiece. Thus Research is needed to controling particle distribution of diamond electrodeposition wheel uniformly. And it is necessary to study micro hole machining such as proximity senser hole, speaker hole positioned Cover-glass. Reinforced glass with the characteristics of the brittle and high hardness is difficult to machining. Processing of reinforced glass have generated wear of tool, micro cracks. Also, it is decreasing shape accuracy. In this paper, We conducted a study on how to control particle distribution uniformly about the diamond tool manufactured using elecetodeposition processing. It analyzed the factors that affect the arrangement of the particles in the electrodeposition process by design of experiment. And There is produced the grinding tool, which derives an optimum deposition conditions, for processing Cover-glass edge and the machinability was evaluated.

• Structural Engineering and Mechanics
• /
• 제62권4호
• /
• pp.465-475
• /
• 2017

Photovoltaic (PV) panels are used in high-rise buildings to convert solar energy to electricity. Due to the considerable energy consumption of high-rise buildings, applying PV technology is of great significance to energy saving. In the application of PV panels, one of the most important construction issues is the connection of the PV panel with the main structures. One major difficulty of the connection design is that the PV panel connection consists of two separate components with coupling and indeterminate dimension. In this paper, the gap element is employed in these two separated but coupled components, i.e., hook and catch. Topology optimization is applied to optimize and design the cross-section of the PV panel connection. Pareto optimization is conducted to operate the optimization subject to multiple load scenarios. The initial design for the topology optimization is determined by the common design specified by the Technical Code for Glass Curtain Wall Engineering (JGJ 102-2003). Gravity and wind load scenarios are considered for the optimization and numerical analysis. Post analysis is conducted for the optimal design obtained by the topology optimization due to the manufactory requirements. Generally, compared with the conventional design, the optimized connector reduces material use with improved structural characteristics.

• 한국기계가공학회지
• /
• 제13권3호
• /
• pp.6-14
• /
• 2014

Touch panels are widely used in the modern display industry as the cover glass of smart mobile phones and tablet PCs. Glass cutting machines are commonly used to cut the panels into their proper sizes. Vibration of these glass cutting machines is assumed to be the main factor leading to the creation of burrs, notches, cracks, scratches and chips on the cut surfaces, eventually causing defects of the cover glass. In this study, the vibrations of a glass cutting machine used for the shearing of cover glass components were analyzed through an experiment and a computer simulation. The structural properties leading to vibration were also analyzed in an effort to determine design alterations which can suppress these vibrations. Moreover, each design alteration was applied to a computer simulation model to determine the effect of different alteration on suppressing vibration. The results show that simple design alterations can substantially suppress vibrations of glass cutting machines.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.356-358
• /
• 2004

In this paper we fabricated and succeeded to demonstrate a test panel for AMOLED on 2" glass and PET substrate. The test panel consisted of an array of 64 x 64 pixels in which OLEDs was driven by pentacene TFT. OTFTs were made of the inverted staggered structure and employed polyvinylphenol as the gate insulator and pentacene thin film as the active layer, producing the filed effect mobility of 0.3$cm^2$/V.sec and on/off current ratio of $10^5$. OLEDs were composed of TPD for HTL and Alq3 for EML with 35nm thick each, generating green monochrome light.