• Journal of the Korean Vacuum Society
• /
• v.16 no.2
• /
• pp.110-115
• /
• 2007

A plasma enhanced atomic layer deposition(PEALD) system has been constructed adopting an inductively coupled plasma(ICP) source with an ALD system, and its plasma generation was carried out. Cobalt thin films were deposited on a p-type Si(100) wafer at $230^{\circ}C$. $Co_{2}(CO)_{6}$ was used as a cobalt precursor, $NH_{3}$ as a reactant, and Ar as a carrier and purge gas. The properties of the thin films were investigated using field emission scanning electron microscopy(FESEM) and auger electron spectroscopy(AES). Large amounts of impurities were found in both the ALD film and the PEALD film, however, the amount of impurities in the PEALD film was reduced to about 50 % compared to that in the ALD film. It was found that $NH_{3}$ plasma, very effectively, induces the reaction with carbon in a cobalt precursor.

• Journal of Korean Society on Water Environment
• /
• v.30 no.3
• /
• pp.261-268
• /
• 2014

Four clays (both natural and commercial types) mainly used in Korea were tested for removal efficiency of Microcystis spp. and ecotoxicity on Daphnia magna and Vibrio fischeri. Four clays (clay A~D) were composed of 91.9~100% of sand (0.02~0.2 mm in particle size). Clay D consisted of lager particles than other clays. Major elements of the four clays were $SiO_2$ (45.3~62.8%), $Al_2O_3$ (18.5~29.7%) and $Fe_2O_3$ (5.4~7.9%). They contained kaolinite (clay mineral), quartz, muscovite, and so on. Clay C and D contained montmorillonite, one of the clay minerals improving clay-cell aggregation. For clay A, B and C, removal efficiency of Microcystis spp. was over 60% at 2 g/L. It reached about 100% at over 5 g/L. For clay D, it was over 60% and 95~100% at 5 g/L and 20 g/L respectively. After adding clays, pH decreased. The greatest drop of pH appeared at clay C. Except for addition of 100 g/L clay C, ecotoxicity on D. magna and V. fischeri didn't appeared at all dose of clays.

• Korean Journal of Environmental Agriculture
• /
• v.26 no.3
• /
• pp.259-266
• /
• 2007

Enormous amount of zeolite by-products as a fine powder have been produced while manufacturing commercial zeolite products. Granulation of the zeolite by-products is necessary in order for them to be recycled as soil conditioners or absorbent for various environmental contaminants due to the limitations inherent from their physical properties. We granulated the zeolite powders using Portland cement as a cementing agent and characterized the physical and chemical properties of the granulated zeolite product. The experimental natural zeolite had a Si/Al ratio of 4.8 and CEC of 68.1 $cmol_c\;kg^{-1}$. The X-ray diffractometry (XRD) revealed that clinoptilolite and mordenite were the major minerals of natural zeolite. Smectite, feldspar and quartz also existed as secondary minerals. Optimum conditions of granulated zeolite production occurred when natural zeolite was mixed with Portland cement at a 4:1 ratio and granulated using the extruder, left to harden for one month at $25^{\circ}C$ and treated at $400^{\circ}C$ for 3 hours. The wide spectra of XRD revealed that the granulated zeolite had amorphous oxide minerals. The alkali- or thermal-treated natural zeolite exhibited pH-dependent charge properties. The major minerals of the granulated zeolite were clinoptilolite, mordenite and tobermorite. The buffering capacity and charge density of the granulated zeolite were greater than those of natural zeolite.

• Restorative Dentistry and Endodontics
• /
• v.47 no.1
• /
• pp.4.1-4.13
• /
• 2022

Objectives: This study evaluated the effects of different smear layer preparations on the dentin permeability and microtensile bond strength (µTBS) of 2 self-etching adhesives (Clearfil SE Bond [CSE] and Clearfil Tri-S Bond Universal [CTS]) under dynamic pulpal pressure. Materials and Methods: Human third molars were cut into crown segments. The dentin surfaces were prepared using 4 armamentaria: 600-grit SiC paper, coarse diamond burs, superfine diamond burs, and carbide burs. The pulp chamber of each crown segment was connected to a dynamic intra-pulpal pressure simulation apparatus, and the permeability test was done under a pressure of 15 cmH₂O. The relative permeability (%P) was evaluated on the smear layer-covered and bonded dentin surfaces. The teeth were bonded to either of the adhesives under pulpal pressure simulation, and cut into sticks after 24 hours water storage for the µTBS test. The resin-dentin interface and nanoleakage observations were performed using a scanning electron microscope. Statistical comparisons were done using analysis of variance and post hoc tests. Results: Only the method of surface preparation had a significant effect on permeability (p < 0.05). The smear layers created by the carbide and superfine diamond burs yielded the lowest permeability. CSE demonstrated a higher µTBS, with these values in the superfine diamond and carbide bur groups being the highest. Microscopic evaluation of the resin-dentin interface revealed nanoleakage in the coarse diamond bur and SiC paper groups for both adhesives. Conclusions: Superfine diamond and carbide burs can be recommended for dentin preparation with the use of 2-step CSE.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.1 s.51
• /
• pp.1-6
• /
• 2007

Hectorite was synthesized by a two-step hydrothermal process from $Mg(OH)_{2}$, water glass (${\sim}30\;wt%\;SiO_{2}$) and Li-compound at $90{\pm}5^{\circ}C$. The product shows excellent dispersion and swelling properties. The mixture of the starting materials was heated in a glass vessel for the first reaction with continuous stirring and the pH of the solution was adjusted to $6{\sim}8$, resulting in the formation of a precursor of hectorite. The excess salt components were washed out from the resulting slurry and then was matured in the glass vessel for the 2nd reaction. Li compound was added during the reaction. After a 10 h retention, the gel of hectorite was formed. The XRD pattern of the synthesized one was coincided with that of natural hectorite and SEM study revealed uniform grains 50 m in diameter. The d001 basal spacing of the product moved from 12 to $17.4\;{\AA}$ after glycolation treatment. The measured value of CEC and the swelling capacity was 90 cmol/kg and $60{\sim}70\;mL/2\;g$, respectively.

• Journal of the Mineralogical Society of Korea
• /
• v.3 no.1
• /
• pp.1-6
• /
• 1990

Clacic amphiboles along the tremolite (Tr)-tschermakite(Ts) joint were synthesized using a piston-cylinder appratus. At 750-85$0^{\circ}C$and 12-2 kb, amphibole+corundum coexist with zoisite($\pm$talc, chlorite, and Mg-staurolite), but with anorthite($\pm$cholorite, spinel, pyroxenes, and sapphirine) at lower P. At 90$0^{\circ}C$, amphibole+corundum+clinopyroxene($\pm$anorthite, forsterite, sapphirine, and garnet) are stable over the P range 12-18 kb. These amphibole-bearing assemblages are replaced at high P by clcinopyroxene+talc+chlorite+zoisite at 650-75$0^{\circ}C$, and at higher temperatures by garnet+clinopyroxene($\pm$zoisite, orthopyroxene, and Mg-staurolite). Synthetic amphiboles with Ts>~45 mol% contain as much as 0.15 excess cations per formula unit(pfu) based on 23 oxygens(anhydrous formula), whereas less tschermakitic ones are deficient in cation occupancy by up to 0.18 pfu. This trend is attributed to the 야/trioctahedral substitution in Ca-amphiboles. Compositions of synthetic amphiboles display systematic changes with P and T governed by coexisting mineral assemblages. The Ts content (=[8-Si-Na]/2) increases with increasing T( Ts/ T=~0.1 nik% K-1) in the range 750-85$0^{\circ}C$, but remains nearly constant at 850-90$0^{\circ}C$. Pressure dramatically affects the Ts content of Ca-amphiboles:it increases with P at 8-12 kb( Ts/ T=2-3 mol% K-1), but significantly decreases at 12-21 kb( Ts/ P=-2.5 mol% Kb-1). Hence, the most tschermakitic amphiboles, containing 60$\pm$5 mol % Ts, or 1.2$\pm$0.1 tetrahedral Al, occur at 12 kb and 850-90$0^{\circ}C$. Compositions of Ca-amphiboles defined by a simple reaction, 3 Tr+2 zoisite+7 corundum+H2O=5 Ts, are reversed and used to estimate thermodynamic parameters of tschermakite assuming ideal mixing of Tr-Ts solid solutions. Predicted standard molal entropy and enthalpy of tschermakite are : S$^{\circ}$of Tr-Ts solid solutions. Predicted standard molal entropy and enthalpy of tschermakite are : S$^{\circ}$=566.9$\pm$13.7 J mol-1K, -1and H$^{\circ}$=-12518.36$\pm$15.17 kJ mol.-1

• Korean Journal of Environmental Agriculture
• /
• v.14 no.3
• /
• pp.263-271
• /
• 1995

Chemical assessment of soil pollution with heavy metals was made by analyzing the changes in pH, ionic strength, cationic concentration and chemical species in the soil solution. Saturated pastes of the unpolluted soils were made by adding solutions containing Cu or Cd and the final Cu or Cd concentrations were in the range of 0 to 400 mg/kg. After equilibrating for 24 hours at $25^{\circ}C$, the soil solution was extracted from the saturated pastes by the vacuum extraction method and analyzed for pH, electrical conductivity, Cu, Cd, cations and inorganic ligands. Chemical species in soil solution were calculated by the GEOCHEM-PC program employing the input variables of pH, ionic strength(${\mu}$), molar concentrations of cations and ligands. Increasing Cu or Cd additions lowered pH of the soil solution but increased concentrations of Ca, Mg and K resulting in increases of ${\mu}$ of the soil solution. Effects of Cu on lowering pH and increasing ${\mu}$ were greater than those of Cd. Concentrations of Cu or Cd in soil solution were relatively very low as compared to those of additions, but increased linearly with increasing additions representing that concentrations of Cu were higher than those of Cd. At 400 mg/kg additions, concentrations of Cu were in the range of 0.51 to 11.70 mg/L but those of Cd were 34.4 to 88.5 mg/L. Major species of Ca, Mg and K were free ions and these species were equivalent to greater than 95 molar % of the existing respective molar concentrations. These cationic species were not changed by Cu or Cd additions. Major species of Cu in lower pH soils such as SiCL and SL were free $Cu^{2+}$ (>95 molar %), but those in LS having a higher pH were free $Cu^{2-}$ and Cu-hydroxide complex. At 100 mg Cu/kg treatment, $Cu^{2+}$ and Cu-hydroxide complex were equivalent to 73 and 22.4 molar %, respectively. These respective percentages were decreased and increased correspondingly with increasing Cu treatments. Major species of Cd in soil solution were free $Cd^{2+}$ and Cd-chloride complex, representing 79 to 85 molar % for $Cd^{2+}$ and 13 to 20% for Cd-chloride complex at 10 mg Cd/kg treatment. With increasing Cd additions to 400 mg/kg, $Cd^{2+}$ species decreased to $40{\sim}47%$ but Cd-chloride complexes increased to $53{\sim}60$ molar %. These results demonstrated that soil contamination with heavy metals caused an adverse effect on the plant nutritional aspects of soil solution by lowering pH, increasing cations temporarily, and increasing free metal concentrations and species enough to be phytotoxic.

• KSBB Journal
• /
• v.23 no.1
• /
• pp.83-89
• /
• 2008

Food wastewater derived from the three-stage methane fermentation system developed in this lab contained high concentration organic substances. The organic wastewater should be treated through advanced wastewater treatment system to satisfy the "Permissible Pollutant Discharge Standard of Korea". In order to treat the organic wastewater efficiently, several optimum operation conditions of a modified $UV/TiO_{2}$ photocatalytic system have been investigated. In the first process, wastewater was pre-treated with $FeCl_{3}$. The optimum pH and coagulant concentration were 4.0 and 2000mg/L, respectively. Through this process, 52.6% of CODcr was removed. The second process was $UV-TiO_{2}$ photocatalytic reaction. The optimum operation conditions for the system were as follows: UV lamp wavelength, 254 nm; wastewater temperature, $40^{\circ}C$; pH 8.0; and air flow rate, 40L/min, respectively. Through the above two combined processes, 69.7% of T-N and 70.9% of CODcr contained in the wastewater were removed.

• Applied Biological Chemistry
• /
• v.27 no.4
• /
• pp.238-244
• /
• 1984

To produce inulase from Kluyveromyces fragilis No.351 using Jerusalem artichoke tuber extract, optimization of the condition was conducted. As results, the optimal concentration of artichoke tuber extract was 3.5 % and bactocasitone showed better production than yeast extract. The optimal temperature and pH were $30^{\circ}C$ and 5.5, respectively. The addition of $NH_4H_2PO_4$ increased the enzyme production. Inulase synthesis was growth-associated and the enzyme production increased as concentration of dissolved oxygen increased. A higher quantity of industrial grade inulase was prepared by the combination of ultrafiltration and ethanol precipitation with 72% recovery.

• Resources Recycling
• /
• v.16 no.5
• /
• pp.31-35
• /
• 2007

The formation of silica sol from sodium silicate solution and the growth of silica sols were investigated in this study. The $SiO_2$ content of 2% in sodium silicate solution was proper to oxidize sodium silicate with sulfuric acid. After the removal of sodium ions in sodium silicate solution, the pH of silicate solution had to be controlled above 9 for a stable silicate solution. The silica sol, which size is about 10 nm, could be prepared by heating the mixed solution of sodium silicate and silicate solution removed sodium ions at pH 10 and 80. And the silica sol grew into about 50 nm as silicate solution was added to silica sol solution.