• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.1
• /
• pp.107-116
• /
• 2012

In this paper, the trade-off related to bandwidth of high-speed common-mode logic frequency divider is analyzed in detail. A method to optimize the operating frequency, band-width as well as power consumption is proposed. This method is based on bipolar device characteristics, whereby a negative resistance model can be used to estimate the optimal normalized upper frequency and lower frequency of frequency dividers under different conditions, which is conventionally ignored in literatures. This method provides a simple but efficient procedure in designing high performance frequency dividers for different applications. To verify the proposed method, a static divide-by-2 at millimeter wave ranges is implemented in 180 nm SiGe technology. Measurement results of the divider demonstrate significant improvement in the figure of merit as compared with literatures.

• Journal of the Korean Society of Visualization
• /
• v.17 no.3
• /
• pp.52-58
• /
• 2019

Thermal performance and flow patterns inside the closed loop pulsating heat pipe (CLPHP) were experimentally investigated. For investigating the effect of working fluids, CLPHP was filled with various working fluids including methanol, acetone and ethanol. The thermal resistance was calculated by temperatures in evaporator and condenser and flow patterns were visualized by a digital camera. The thermal resistances for all fluids were decreased as the heat increases. Flow patterns change from static slug to elongated slug flows, bulk circulation and annular flows as the heat increases. Dry-out occurs after annular flows. For reasonable comparison of thermal performances, normalized CHF, Kutateladze number (K_u), was compared. Even though ethanol has smallest CHF, K_u of ethanol is similar with that of methanol. In addition, acetone has the highest K_u that means CLPHP with acetone provides the higher thermal performance compared with CLPHP with other fluids.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.8
• /
• pp.1019-1023
• /
• 2018

In this paper sensitivity analysis of temperature on special day electricity demand of land and Jeju Island is performed. The basic electricity demand per 3 hours is defined as electricity demand that reflects the GDP effect without the temperature influence. The temperature sensitivity per 3 hours is calculated through the relationship between special day electricity demand normalized to basic electricity demand and temperature. In the future, forecast error will be improved if the temperature sensitivity per 3 hours is applied to the special day load forecasting.

• Food Science and Preservation
• /
• v.14 no.6
• /
• pp.688-694
• /
• 2007

To evaluate the human risk of long-term intake of genetically modified (GM) rice, we carried out RT-PCR of housekeeping genes. Housekeeping genes, which show highly uniform expression in living organisms during various stages of development and under different environmental conditions, were normalized by RT-PCR. We assessed the expression of 10 common housekeeping genes (18s rRNA, 25S rRNA, UBC, UBQ5, UBQ10, ACT11, GAPDH, eEF-$1{\alpha}$, ${\beta}$-TUB, GAPDH, ${\beta}$-actin, B2m, G6pd2, Gyk, Gus, Hprt, Cyclophlin A, Tfrc, ${\alpha}$-tubulin and RPL13A) in the liver, stomach, small intestine, large intestine, kidney and spleen of mice fed GM or non-GM rice. We found no significant differences in the expression of housekeeping genes between the two groups of mice.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.293-294
• /
• 2015

This work considers the elliptic restricted three-body problem under effects of radiation of the bigger primary, and an oblate spheroid for the smaller primary to mimic an exoplanetary system with a gas giant planet. Under the influences of both effects we look for the existence of the triangular equilibrium points and the influences of the radiation and oblateness on the locations and motion of the points. We set the system in a normalized rotating coordinate system and derive equations of motion for the third infinitesimal object. Our study shows that the effects modify the equilateral/isosceles triangle shape with respect to the primaries. The triangular points also have non-planar motion with period depending on the value of the planet oblateness.

• Macromolecular Research
• /
• v.12 no.1
• /
• pp.107-111
• /
• 2004

We have studied the polymerization kinetics of acrylamide in aqueous solution with potassium persulfate as an initiator by using quantitative real-time in situ IR spectroscopy and monitoring the profiles of peaks in the range 1900-850 cm$\^$-1/. The conversion of acrylamide was calculated from the disappearance of the peak at 988 cm$\^$-1/, which is the out-of-plane bending mode of the=C-H unit, normalized to the C=O stretching peak at 1675 cm$\^$-1/, as an internal standard. For reaction temperatures in the range 40-65$^{\circ}C$ and initiator and monomer concentrations of 0.9-2.6 mmol/L and 0.5-1.1 mol/L, respectively, we deduced that the rate of monomer consumption follows the relation R$\_$p/=k［K$_2$S$_2$O$\_$8/］$\^$0.5/ [Μ］$\^$1.35${\pm}$0.10/. In addition, we obtained activation parameters from an evaluation of the kinetic data.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1612-1614
• /
• 2003

80pF capacitive couplers were connected to six 6.6kV motor model coil terminals. The voltage applied to the coils were 3.81kv, 4.76 kV and 6.6kV, respectively. These stator coils have various types of artificial insulation defects such as large voids, semi-conductive coating damage and strand insulation fault. Digital PD detector(PDD) and turbine generator analyzer(TGA) were used to measure PD activity. TGA summarizes each plot with two quantities such as the normalized quantity number(NQN) and the peak PD magnitude(Qm). The PD levels in PD were measured with a conventional digital PD detector. Most of the defect mechanism of large motor stator winding can be associated with PD patterns such as internal and slot discharges. PD patterns coincide with PDD and TGA. These instruments have an input bandwidth of 40-400kHz and 0.1-350MHz. Surge testing detects faults in inter-turn winding of high voltage motor model coils.

• International Journal of Concrete Structures and Materials
• /
• v.6 no.2
• /
• pp.101-110
• /
• 2012

This paper focuses on the finite element (FE) response sensitivity and reliability analyses considering smooth constitutive material models. A reinforced concrete frame is modeled for FE sensitivity analysis followed by direct differentiation method under both static and dynamic load cases. Later, the reliability analysis is performed to predict the seismic behavior of the frame. Displacement sensitivity discontinuities are observed along the pseudo-time axis using non-smooth concrete and reinforcing steel model under quasi-static loading. However, the smooth materials show continuity in response sensitivity at elastic to plastic transition points. The normalized sensitivity results are also used to measure the relative importance of the material parameters on the structural responses. In FE reliability analysis, the influence of smoothness behavior of reinforcing steel is carefully noticed. More efficient and reasonable reliability estimation can be achieved by using smooth material model compare with bilinear material constitutive model.

• Structural Engineering and Mechanics
• /
• v.14 no.6
• /
• pp.649-660
• /
• 2002

Experimental results are presented from tests conducted on reinforced concrete beam-column joints with lap splices under reversed cyclic loading simulating earthquake action. Response curves are compared for twenty-four specimens designed according to Eurocode 2. The main parameters of the investigation are, the geometry of the reinforcing bar extension, the applied axial load (normalized), the available cover over lap splice region extended as length required from Eurocode 2, as well as the shape and the volumetric percentage of the stirrups confining the lap splice zone. The results are evaluated with regards to the load intensity, the energy absorption capacity and the characteristics of the load deflection curve.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.6 no.2
• /
• pp.17-36
• /
• 1987

In this experimental research, fracture mechanisms of spheroidal graphite cast iron (As Cast, annealed and normalized) were investigated by using Acoustic Emission (AE) technique. In this study, the data (AE signal) are digitized and processed with the 8 bits micro-computer (APPLE II) connected to the AE measuring device without data processing unit. The source of AE signal was estimated by fractography analysis. The results obtained in this experimental study are summarized as follows : For the heterogeneous materials (spheroidal graphite cast iron) with inclusions which may considered as cracks, it is found that low and high AE amplitude appear simultaneously and the load is found to be fluctuated in the final stage of deformation. But the lad is not fluctuated in tension test with low AE amplitude only. AE is measured within elastic region and it is confirmed that 0.2% offset yield load agrees approximately with the load point where AE counts decrease steeply after the point of maximum AE counts.