• International Journal of Concrete Structures and Materials
• /
• 제6권4호
• /
• pp.231-237
• /
• 2012

Recently, it has been difficult to get natural sand for concrete due to an insufficient supply in Korea. Crushed sand was thought as a substitute and previous research has been focused on low fluidity and normal compressive strength (24-30 MPa). Study on high performance concrete using crushed sand is hardly found in Korea. In this study it was investigated that the effect of the crushed sand on fluidity and compressive strength properties of high performance concrete. Blending crushed sand (FM: 3.98) produced in Namyangju, Kyunggido and sea sand (FM: 2.80) produced in Asan bay in Chungnam. The final FMs of fine aggregate were 3.50, 3.23, and 3.08. W/B was set as 0.25 to get high performance. With the test results an analysis of relationship was performed using a statistical program. It was shown that strength property of concrete using crushed aggregate at the very early age or after specific time was mainly affected by strength development properties of binders instead of the crushed sand.

• 한국해양공학회지
• /
• 제1권1호
• /
• pp.84-93
• /
• 1987

A beach nourishment method can be used as one of the beach erosion protection methods which may keep coastal environments whithout constructing coastal structures on the HAE UN DAE beach. The beach nourishmens is affected by a natural condition and artificial condition;a natural condition includes conditions of bottom slope, diameter of bottom materials and waves, and artificial conditions include deposit position, method, diameter and quantity of the nourishing sand. It has accomplished to obtain the deposit position and the best diameter of the nourishing sand from a two-dimensional hydraulic model test, which simulates the erosional HAE UN DAE beach. In this study, the protection of the beach erosion can be maximized when the nourishing sand of 3.3mm in diameter, which is about 5.5.times of the bottom materials in diameter, is deposited layerly in front of the breaker zone which has a water depth of 4.6m.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.81-84
• /
• 2006

Currently, natural aggregates of good quality are hard to use because of continuous decrease of internal aggregate resource and regulation of gathering. So, use of crushed sand was being increased. On the other hand, skyscraper projects with 100 stories are being planned within the country and high strength concrete must be used to construct a skyscraper with 100 stories. High strength concrete is necessary to use crushed sand too because we are still unable to secure natural aggregates of good quality. So, This study indicated basic data necessary for mix design of high strength concrete through valuation of concrete property by quality variation of crushed sand.

• 한국항만학회지
• /
• 제9권1호
• /
• pp.65-72
• /
• 1995

This study is being done for the purpose to achieve a stable demand and supply of materials for long term. The author investigated condition of suitable mixer design method for concrete, an individual value and a character of dynamics as a supplement material by drying up the natural aggregate, and a possible practicalization plan to reduce defects to the minimum. As a result of this study, it can be acquired a good quality of concrete by the use of the natural sand (Nak Dong river sand) and the crushed sand with suitable mixing ratio. The fineness modulus (F.M) of mixing aggregate is $2.7\pm1$ at this time and this is good for workbility and plasticity of concrete.

• 콘크리트학회논문집
• /
• 제18권2호
• /
• pp.249-255
• /
• 2006

최근 건설현장에서 다양한 잔골재가 콘크리트에 사용되고 있으나, 이런 잔골재가 콘크리트에 미치는 영향에 대해 체계적으로 검토한 연구는 거의 없다. 따라서 본 연구에서는 최근 국내 건설현장에서 비교적 많이 사용되고 있는 잔골재 종류가 콘크리트의 품질에 미치는 영향을 검토할 목적으로 잔골재 종류가 콘크리트의 건조수축, 내구성, 수밀성에 미치는 영향을 분석하였다. 그 결과, 부순모래를 사용한 콘크리트는 바닷모래 및 강모래와 같은 천연모래를 사용한 콘크리트에 비해 건조수축이 증가되고, 내구성과 수밀성이 저하되며, 특히 입도 입형이 불량한 부순모래를 사용한 경우에는 더욱 콘크리트의 품질을 저하시키는 것으로 나타났다. 또한 입도 입형이 불량한 부순모래를 천연모래와 혼합하여 입도와 입형을 적절히 조절함으로써 콘크리트의 건조수축이 저감되고, 내구성과 수밀성이 향상되는 것으로 나타났다.

• Geomechanics and Engineering
• /
• 제37권2호
• /
• pp.167-178
• /
• 2024

The natural frequency shift under cyclic environmental loads is a key issue in the design of monopile-based offshore wind power turbines because of their dynamic sensitivity. Existing evidence reveals that the natural frequency shift of the turbine system in sand is related to the varying foundation stiffness, which is caused by soil deformation around the monopile under cyclic loads. Therefore, it is an urgent need to investigate the effect of soil deformation on the system frequency. In the present paper, three generalized geometric models that can describe soil deformation under two-way cyclic loads are proposed. On this basis, the cycling-induced changes in soil parameters around the monopile are quantified. A theoretical approach considering three-spring foundation stiffness is employed to calculate the natural frequency during cycling. Further, a parametric study is conducted to describe and evaluate the frequency shift characteristics of the system under different conditions of sand relative density, pile slenderness ratio and pile-soil relative stiffness. The results indicate that the frequency shift trends are mainly affected by the pile-soil relative stiffness. Following the relevant conclusions, a design optimization is proposed to avoid resonance of the monopile-based wind turbines during their service life.

• 한국주조공학회지
• /
• 제43권3호
• /
• pp.107-136
• /
• 2023

주강품 사형주조에는 천연규사가 보편적으로 사용되었고, 규사의 열적특성 부족에 의한 소착결함 억제를 위해, 크로마이트사가 사용되기도 하였으나, 반복 사용에 의한 골재 열화, 시스템샌드 혼입 문제, 분리 제거의 어려움, 높은 밀도에 따른 조형 시 하중증가, 크롬 함유 폐기물이 되는 단점이 있다. 최근에는 주조업계의 중요한 과제로써 산업폐기물 저감 및 대기환경 개선이 부각되고 있다. 종래의 주물사 사용 시 발생되는 문제점 해결과 주조공장의 환경개선을 위해서, 천연사를 대체 적용할 수 있는 다양한 인공사가 개발되어 소개되고 있다. 인공사는 용융분사법으로 제조된 인공사와 조립소결법으로 제조된 인공사 및 분쇄법으로 제조된 인공사로 분류할 수 있으며, 원료광물의 종류, 제조공법에 따라 상이한 물리적 특성을 나타낸다. 본 연구에서는 각종 주물사의 물성, 주형강도, 물리적 내구성, 열적 내구성, 소착시험편 주조 등의 비교 평가시험을 하였다. 밀도에 따른 주물사 실사용량, 주물사 형상에 따른 주형강도, 주물사의 물리적 및 열적 내구성, 주물사의 내열특성을 종합적으로 고려하였을 때, 아크용사법으로 제조된 용융인공사 A1 또는 분말식화염용사법으로 제조된 용융인공사 B가 대형주강품 주조에 가장 적합한 구형의 인공사로 판단된다.

• 한국지반신소재학회논문집
• /
• 제4권2호
• /
• pp.3-9
• /
• 2005

최근 모래가격이 급등하고 수급이 어려워져 비교적 가격이 저렴한 코코넛껍질 압축매트와 황마필터로 구성된 수평 천연섬유배수재가 모래 대체재료로서 각광 받고 있다. 본 연구에서는 수평 천연섬유배수재의 인장강도와 투수특성을 평가하여 수평 배수재로서의 사용성을 평가하였다. 수평 천연섬유배수재의 인장특성을 분석한 결과 코코넛껍질 매트의 매우 낮은 인장강도에도 불구하고 대부분의 인장강도가 황마필터에서 발휘되므로 Christopher와 Holtz(1985)가 제안한 일반적인 토목섬유에 대한 인장강도 기준을 훨씬 상회하는 것으로 나타났다. 또한, 매우 높은 압축하중에서 수평 천연섬유배수재의 투수성을 평가한 결과 일반적인 모래의 투수계수보다 높은 투수성을 나타내는 것으로 평가되었다. 이와 같은 결과를 종합적으로 분석하면, 수평 천연섬유배수재는 기존의 모래재료를 대체할 수 있는 배수재료로 사용이 가능할 것으로 판단된다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 추계 학술논문 발표대회
• /
• pp.63-66
• /
• 2005

Recently, Trouble of sand supply is occurred according to exhaustion of natural sand resources. therefore, various measures are proposed for solution of trouble of sand supply also the government settled trouble of sand supply through application of crushed sand. but because both crushed sand are poor against general sand, they lead to lowering of qualify of ready-mixed concrete. Therefore, this study evaluated engineering property and durability of concrete using crushed sand and applied evaluation result to fundamental data for quality control of concrete using crushed sand. The results of this study have shown that quality of concrete using crushed sand independently is poor against general concrete. but, the workability, compressive strength and durability of concrete mixed crushed sand with genera can improve on those of concrete used general sand.

• 산업기술연구
• /
• 제22권A호
• /
• pp.119-125
• /
• 2002

In Kwangjin industrial company, mill is operating for the foundry sand production at the rate of 25t/hr from quartzite. Foundry sands fall into four distinct categories: silica sand, lake sand, bank sand, and natural molding sand. Silica sand is a general term used to describe crushed, washed, graded, dried, and cooled clay-free sands. This study was conducted for the investigation of the foundry sand productivity and the life span of the hammer according to the material quality. The life time of hammer from several manufacturer were compared in order to find out the grinding efficiency of the various hammer material. In the result of tests, the life time of high-Mn hammer was 10.5 hours while that of high-Cr was 19.5 hours. The life time in case of typical worn shape hammers was about 12 hours and the average time of a blowhole hammer was about 6.5 hours.