• 한국분말재료학회지
• /
• 제8권3호
• /
• pp.163-167
• /
• 2001

A bulk porous $CaZrO_3/MgO$ composite with plantinum nano-dispersion was synthesized in air atmosphere through the combination of several in situ reactions, including the pyrolysis of $PtO_2$. A mixture of $CaMg(CO_3)_2$(dolomite), $ZrO_2$, $PtO_2$ and LiF (0.5 wt%, as an additive) was cold isostatically pressed at 200 MPa and sintered at $1100^{\circ}C$ for 2 h. The porous $CaZrO_3/MgO/Pt$ composite ($CaZrO_3/MgO$ : Pt=99 : 1 in volume) had a uniformly open-porous structure (porosity: 56%) with three-dimensional (3-D) network and a narrow pore-size distribution, similarly to the porous $CaZrO_3/MgO$ composites reported before. Catalytic Properties (viz., NO direct decomposition and NO reduction by $C_2H_4$) of the $CaZrO_3/MgO/Pt$ composite were investigated up to $900^{\circ}C$. In the absence of oxygen, the NO conversion rate reached ~52% for the direct decomposition and ~100% for the reduction by $C_2H_4$, respectively. The results suggest the possibility of the porous composite as a multifunctional filter, i.e., simultaneous hot gas-filtering and $de-NO_x$ in one component.

• 전기전자학회논문지
• /
• 제21권1호
• /
• pp.24-29
• /
• 2017

본 연구에서는 수용성 아크릴 에멀젼 접착제를 주성분으로 스틸렌 모노머(stylene monomer)와 메틸올 아크릴아미드 모노머(methylol acrylamide monomer)를 경화시키고, 여기에 산화환원제와 점도 조절을 통한 나노 탄소타일을 개발한다. 이때 수용성 아크릴 에멀젼 접착제(45 %)와 300~500메시(mesh) 코코넛 숯(55%) 파우더를 일정비율로 25~30분간 혼합 교반하면, 직경 1~3mm 구형체가 형성된다. 성형된 조성물은 소성온도 $90{\sim}300^{\circ}C$에서 30~90분가량의 소성과정을 거친 후 상온에서 건조시키면, 숯 성형물은 95% 이상 순수한 고형활성탄이 된다. 친환경 숯 성형물을 입증하기 위해 원적외선 비율, 에너지 분석, 가스농도 및 항균실험을 실시해 안정성을 확보한다.

• 한국정밀공학회지
• /
• 제21권8호
• /
• pp.34-42
• /
• 2004

A new polishing technique for three dimensional micro/meso-scale parts is suggested using a micro quill and a magnetic chain structure. The principle of this method is to polish the target surface with the collected magnetic brushes at a micro tool by the non-uniform magnetic field generated around the tool. In a typical magnetic abrasive finishing process magnetic particles and abrasive particles are unbonded each other. But, to finish the three dimensional small parts bonded magnetic abrasive have to be used. Bonded magnetic abrasives are made from direct bonding, and their polishing characteristics are also examined. Alumina, silicon carbide and diamond micro powders are used as abrasives. Base metal matrix is carbonyl iron powder. It is found that bonded magnetic abrasives are superior to unbonded one by experiment. finally, the polished surface roughness is evaluated by atomic force microscope.

• Bulletin of the Korean Chemical Society
• /
• 제34권9호
• /
• pp.2737-2740
• /
• 2013

The layered $KTiNbO_5$ was successfully synthesized with titanium(IV) isopropoxide and niobium oxalate by a novel polymerized complex (PC) method. The morphology and structure of the as-prepared sample was characterized by means of High-Resolution Transmission Electron Microscope, powder X-ray diffraction, and Laser Raman Spectroscopy. The spectral response characteristic was recorded by using UV-vis Diffuse Reflectance Spectroscopy. Results show that $KTiNbO_5$ as-prepared by PC method presents an uniform morphology of nano-particles, the mean particle sizes is ca. 28 nm corresponding to the (002), and the crystal structure can be well indexed to the orthorhombic phase. The sample as-prepared by PC method has higher band gap energy than that of the sample prepared by a solid-state reaction method due to the quantum size effect.

• 한국입자에어로졸학회지
• /
• 제5권1호
• /
• pp.1-7
• /
• 2009

Fe- and V-doped titanium dioxide nanoparticles consisting of spherical primary nanoparticles were synthesized from a mixed liquid precursor by using the flame spray pyrolysis. The effects of dopant concentration on the powder properties such as morphology, crystal structure, and light adsorption were analyzed by TEM, XRD, and UV-Vis spectrophotometer, respectively. As the V/Ti molar ratio increased, pure anatase particles were synthesized. On the contrary, rutile phase particles were synthesized as the Fe/Ti ratio increased. Photocatalytic property of as-prepared $TiO_2:Fe,V$ nanoparticles was investigated by measuring the removal efficiency for volatile organic compounds (VOCs) under the irradiation of visible light. After 2 hrs under visible light, the removal efficiencies of benzene, p-xylene, ethylbenzene, and toluene were reached to 21.9%, 21.4%, 19.8% and 17.6% respectively.

• 한국분말재료학회지
• /
• 제14권2호
• /
• pp.97-100
• /
• 2007

The magnetic alloys of Cu-Fe ($Cu_{50}Fe_{50},\;Cu_{80}Fe_{20}\;and\;Cu_{90}Fe_{10}$) were prepared by a mechanical alloying method and their structural and magnetic behaviors were examined by X-ray diffraction and Mossbauer spectra. The magnetization curves did not distinctly show the saturation at 70 kOe for the concentrated alloys of $Cu_{80}Fe_{20}\;and\;Cu_{90}Fe_{10}$. The Mossbauer spectrum of $Cu_{80}Fe_{20}$ at room temperature shows one Lorentzian line of the paramagnetic phase, whereas the Mossbauer spectrum of $Cu_{90}Fe_{10}$ consists of sextet Lorentzian line at room temperature and a centered doublet line. The Mossbauer spectra of $Cu_{90}Fe_{10}$ measured in the temperature ranges from 13 to 295 K, implies that $Cu_{90}Fe_{10}$ to consists of two magnetic phases. One superimposed sextet corresponds to the ferromagnetic iron in Cu and the other one indicates the superparamagnetic iron rich phase.

• 한국분말재료학회지
• /
• 제28권5호
• /
• pp.423-428
• /
• 2021

Here, we report the development of a new and low-cost core-shell structure for lithium-ion battery anodes using silicon waste sludge and the Ti-ion complex. X-ray diffraction (XRD) confirmed the raw waste silicon sludge powder to be pure silicon without other metal impurities and the particle size distribution is measured to be from 200 nm to 3 ㎛ by dynamic light scattering (DLS). As a result of pulverization by a planetary mill, the size of the single crystal according to the Scherrer formula is calculated to be 12.1 nm, but the average particle size of the agglomerate is measured to be 123.6 nm. A Si/TiO₂ core-shell structure is formed using simple Ti complex ions, and the ratio of TiO₂ peaks increased with an increase in the amount of Ti ions. Transmission electron microscopy (TEM) observations revealed that TiO₂ coating on Si nanoparticles results in a Si-TiO₂ core-shell structure. This result is expected to improve the stability and cycle of lithium-ion batteries as anodes.

• 자원리싸이클링
• /
• 제12권6호
• /
• pp.38-46
• /
• 2003

본 연구에서는 새도우마스크 제조공정 중 발생되는 Fe-Ni계 복합 폐산을 원료로 하여 공기압력 1kg/$ extrm{cm}^2$의 조건에서 분무열분해 공정에 의해 평균입도 100nm 이하의 니켈 페라이트($NiFe _2$$O_4$)및 $_Fe2$O$_3$＋NiO 나노 분말을 제조하였으며, 반응온도, 폐산용액의 농도 및 nozzle tip 크기의 반응인자들의 변화에 따른 생성된 분말의 특성 변화를 파악하였다. 반응온도가 $800^{\circ}C$로부터 $1100 ^{\circ}C$로 변화함에 따라 분말의 평균입도는 40nm로부터 100nm 정도까지 증가하고 있었으며 조직은 더욱 치밀화되는 반면 입도분포는 점점 불균일하게 됨을 알 수 있었다. 반응온도의 증가에 따라 니켈 페라이트 상의 생성 비율이 현저히 증가하고 있었으며 분말의 비표면적은 현저히 감소하고 있었다. 원료용액 내의 Fe 성분의 농도가 20g/l로 부터 200g/l로 증가됨에 따라 분말의 평균 입도는 30m로 부터 60nm 정도까지 점점 증가하는 반면 입도분포는 더욱 불균일하게 나타나고 있었다. 또한 용액의 농도 증가에 따라 니켈 페라이트 상의 생성 비율이 증가하고 있었으며, 분말의 비표면적은 현저히 감소하였다. Nozzle tip 크기 증가에 따라 분말의 입도분포는 점점 불균일하게 나타나는 반면 평균 입도는 현저한 변화를 나타내지 않았다. Tip 크기가 2mm까지는 tip 크기 증가에 따라 니켈 페라이트 상의 생성 비율에 현저한 변화는 나타나지 않는 반면 분말의 비표면적은 약간 감소하였다. Tip 크기가 3mm 및 5mm로 증가하는 경우에는 니켈 페라이트 상의 생성 비율이 점점 감소하고 있었으며, 분말의 비표면적은 약간씩 증가하고 있음을 알 수 있었다.

• Bulletin of the Korean Chemical Society
• /
• 제27권9호
• /
• pp.1310-1314
• /
• 2006

Sulfur-substituted $LiMn_{0.9}Cr_{0.1}O_{2-x}S_x$ $(0\;\leq\;x\;\leq\;0.1)$ layered oxides have been prepared by solid state reaction under inert atmosphere. From powder X-ray diffraction analyses, all the present lithium manganates were found to be crystallized with monoclinic-layered structure. Electrochemical measurements clearly demonstrated that, in comparison with the pristine $LiMn_{0.9}Cr_{0.1}O_2$, the sulfur-substituted derivatives exhibit smaller discharge capacities for the entire cycle range but the recovery of discharge capacity after the initial several cycles becomes faster upon sulfur substitution. The effect of the sulfur substitution on the chemical bonding nature of $LiMn_{0.9}Cr_{0.1}O_{2-x}S_x$has been investigated using X-ray absorption spectroscopic (XAS) analyses at Mn and Cr K-edges. According to Mn K-edge XAS results, the trivalent oxidation state of manganese ion remains unchanged before and after the substitution whereas the local structure around manganese ions becomes more distorted with increasing the substitution rate of sulfur. On the other hand, the replacement of oxygen with sulfur has negligible influence on the local atomic arrangement around chromium ions, which is surely due to the high octahedral stabilization energy of $Cr^{+III} $ ions. Based on the present experimental findings, we have suggested that the decrease of discharge capacity upon sulfur substitution is ascribable to the enhanced structural distortion of $MnO_6$ octahedra and/or to the formation of covalent Li-S bonds, and the accompanying improvement of cyclability would be related to the depression of Mn migration and/or to the pillaring effect of larger sulfur anion.

• 한국분말재료학회지
• /
• 제11권6호
• /
• pp.503-509
• /
• 2004

Dispersion stabilities and photocatalytic activities of rutile $TiO_{2}$ powders with unique nano-structure synthesized by homogeneous precipitation process at low temperature(HPPLT) have been investigated in the acrylic resin containing fluorostyrene in the range of 0~0.16 mole. Isoelectric point of $TiO_{2}$ in the acrylic resin placed in the neutral region whereas that of $TiO_{2}$ in the water placed in the acidic region, indicating that zeta potential and agglomeration of $TiO_{2}$ powder is strongly dependent on the pH and the type of solvent. To prepare an adhesion, an acrylic resin containing fluorostyrene was synthesized by a radical polymerization. The adhesion of coating layer was increased with increasing fluorostyrene's contents without changing the dispersion stabilities and degrading photocatalytic properties.