• Electronics and Telecommunications Trends
• /
• v.33 no.6
• /
• pp.12-23
• /
• 2018

In this paper, we review the technical trends of diamond and gallium oxide ($Ga_2O_3$) semiconductor technologies among ultra-wide bandgap semiconductor technologies for harsh environments. Diamond exhibits some of the most extreme physical properties such as a wide bandgap, high breakdown field, high electron mobility, and high thermal conductivity, yet its practical use in harsh environments has been limited owing to its scarcity, expense, and small-sized substrate. In addition, the difficulty of n-type doping through ion implantation into diamond is an obstacle to the normally-off operation of transistors. $Ga_2O_3$ also has material properties such as a wide bandgap, high breakdown field, and high working temperature superior to that of silicon, gallium arsenide, gallium nitride, silicon carbide, and so on. In addition, $Ga_2O_3$ bulk crystal growth has developed dramatically. Although the bulk growth is still relatively immature, a 2-inch substrate can already be purchased, whereas 4- and 6-inch substrates are currently under development. Owing to the rapid development of $Ga_2O_3$ bulk and epitaxy growth, device results have quickly followed. We look briefly into diamond and $Ga_2O_3$ semiconductor devices and epitaxy results that can be applied to harsh environments.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.4
• /
• pp.242-245
• /
• 2021

In this work, we fabricated oxide on an n-type silicon substrate through local anodic oxidation (LAO) using atomic force microscopy (AFM). The resulting oxide thickness was measured and its correlation with load force, scan speed and applied voltage was analyzed. The surface oxide layer was stripped using a buffered oxide etch. Ohmic contacts were created by applying silver paste on the silicon substrate back face. LAO was performed at approximately 70% humidity. The oxide thickness increased with increasing the load force, the voltage, and reducing the scan speed. We confirmed that LAO/AFM can be used to create both lateral and, to some extent, vertical shapes and patterns, as previously shown in the literature.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.11a
• /
• pp.3-4
• /
• 2000

Many researchers are interested in the synthesis and characterization of carbon nitride and diamond-like carbon (DLq because they show excellent mechanical properties such as low friction and high wear resistance and excellent electrical properties such as controllable electical resistivity and good field electron emission. We have deposited amorphous carbon nitride (a-C:N) thin films and DLC thin films by shielded arc ion plating (SAIP) and evaluated the structural and tribological properties. The application of appropriate negative bias on substrates is effective to increase the film hardness and wear resistance. This paper reports on the deposition and tribological OLC films in relation to the substrate bias voltage (Vs). films are compared with those of the OLC films. A high purity sintered graphite target was mounted on a cathode as a carbon source. Nitrogen or argon was introduced into a deposition chamber through each mass flow controller. After the initiation of an arc plasma at 60 A and 1 Pa, the target surface was heated and evaporated by the plasma. Carbon atoms and clusters evaporated from the target were ionized partially and reacted with activated nitrogen species, and a carbon nitride film was deposited onto a Si (100) substrate when we used nitrogen as a reactant gas. The surface of the growing film also reacted with activated nitrogen species. Carbon macropartic1es (0.1 -100 maicro-m) evaporated from the target at the same time were not ionized and did not react fully with nitrogen species. These macroparticles interfered with the formation of the carbon nitride film. Therefore we set a shielding plate made of stainless steel between the target and the substrate to trap the macropartic1es. This shielding method is very effective to prepare smooth a-CN films. We, therefore, call this method "shielded arc ion plating (SAIP)". For the deposition of DLC films we used argon instead of nitrogen. Films of about 150 nm in thickness were deposited onto Si substrates. Their structures, chemical compositions and chemical bonding states were analyzed by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and infrared spectroscopy. Hardness of the films was measured with a nanointender interfaced with an atomic force microscope (AFM). A Berkovich-type diamond tip whose radius was less than 100 nm was used for the measurement. A force-displacement curve of each film was measured at a peak load force of 250 maicro-N. Load, hold and unload times for each indentation were 2.5, 0 and 2.5 s, respectively. Hardness of each film was determined from five force-displacement curves. Wear resistance of the films was analyzed as follows. First, each film surface was scanned with the diamond tip at a constant load force of 20 maicro-N. The tip scanning was repeated 30 times in a 1 urn-square region with 512 lines at a scanning rate of 2 um/ s. After this tip-scanning, the film surface was observed in the AFM mode at a constant force of 5 maicro-N with the same Berkovich-type tip. The hardness of a-CN films was less dependent on Vs. The hardness of the film deposited at Vs=O V in a nitrogen plasma was about 10 GPa and almost similar to that of Si. It slightly increased to 12 - 15 GPa when a bias voltage of -100 - -500 V was applied to the substrate with showing its maximum at Vs=-300 V. The film deposited at Vs=O V was least wear resistant which was consistent with its lowest hardness. The biased films became more wear resistant. Particularly the film deposited at Vs=-300 V showed remarkable wear resistance. Its wear depth was too shallow to be measured with AFM. On the other hand, the DLC film, deposited at Vs=-l00 V in an argon plasma, whose hardness was 35 GPa was obviously worn under the same wear test conditions. The a-C:N films show higher wear resistance than DLC films and are useful for wear resistant coatings on various mechanical and electronic parts.nic parts.

• International Journal of Internet, Broadcasting and Communication
• /
• v.12 no.2
• /
• pp.83-89
• /
• 2020

A microstrip feedline based open ended folded-slot antenna is proposed for ultra-wideband (UWB) applications. The prototype of the proposed antenna is fabricated on the FR4 dielectric substrate. The proposed antenna has a wide n-shaped slot that is useful for designing circuit components on the same printed circuit board (PCB) as that of the radio frequency (RF) modules. The proposed antenna use two kinds of slots as radiators, and each slots have different characteristics because of the different type of ends of the slot. The wideband characteristic can be obtained by resonances of each slot which are occurred at different frequencies. The measured impedance bandwidth (S₁₁≤ -10 dB) is 2.9-11.56 GHz, and the antenna peak gain is 2-4 dBi over the UWB range. The antenna has a stable omni-directional radiation pattern and only a small group-delay variation across the UWB passband. In addition, we present a modified design with band-notched characteristics of a 5 GHz wireless local area network (WLAN) frequency band.

• Journal of the Korean Magnetics Society
• /
• v.19 no.4
• /
• pp.133-137
• /
• 2009

$MnGeP_2$ thin films grown on GaAs exhibit room-temperature ferromagnetism with $T_C{\sim}$320 K, based on both magnetization and resistance measurements. The coercive fields at 5, 250, and 300 K are 3870, 1380 and 155 Oe, respectively. The anomalous Hall effect was observed, indicating spin polarization of the carriers. Hysteresis has been observed in both magnetoresistance and Hall measurements. The current-voltage characteristics of a $MnGeP_2$ film grown on an n-type GaAs substrate display semiconducting behavior.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.6
• /
• pp.280-284
• /
• 2020

Electron beam irradiation is widely used as a type of surface modification technology to advance surface properties. In this study, the effect of electron beam irradiation on properties, such as surface hardness, wear resistance, roughness, and critical load of Titanium Aluminium nitride (TiAlN) films was investigated. TiAlN films were deposited on the SKD-61 substrate by using cathode arc ion plating. After deposition, the films were bombarded with intense electron beam for 10 minutes. The surface hardness was increased up to 4520 HV at electron irradiation energy of 1500 eV. In addition, surface root mean square (RMS) roughness of the films irradiated at 1500 eV shows the lowest roughness of 484 nm in this study.

• Applied Chemistry for Engineering
• /
• v.17 no.2
• /
• pp.194-200
• /
• 2006

Titanium oxide films were deposited by the nozzle type HCP RT-MOCVD for the application of metal-oxide films. In the case of TTNB, after depositing films, films must be annealed at a proper temperature, but in the case of titanium ethoxide, titanium oxide films could be directly deposited by titanium ethoxide without general annealing. We could confirm that ratio of O to Ti in the films was about 2 : 1 at RF-power of 240 watt, distance between cathode and substrate of 3 cm, deposition time of 20 min, and ratio of Ar to $O_2$ of 1 : 1. Therefore, we could obtain the titanium oxide film deposited by the nozzle type HCP RT-MOCVD without an annealing process and could apply in the metal-oxide deposition process at a low temperature.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1440-1441
• /
• 1995

We fabricated diode-type silicon field emitter array device and tested the current-voltage characteristics. Silicon oxide layer having the thickness of $1{\mu}m$ is grown in the (100) oriented n-type silicon substrates. Oxide layer is patterned by the mask with $10{\mu}m$ diameter circles. Silicon substrate is then etched using NAF 1 solution to form the sharp tip arrays as an electron source. In the UHV test station, we tested the current-voltage characteristics for the samples. Turn-on voltage was about 140V and maximum emission current was $310{\mu}A$ at 164V. We studied about silicon bonding process for future work, too.

• Journal of Sensor Science and Technology
• /
• v.6 no.3
• /
• pp.237-244
• /
• 1997

A new planar-type microsensor, which had a platinum heater and a sensing layer on the same plane was fabricated on silicon substrate with stress-relieved PSG(phosphosilicate glass)/$Si_{3}N_{4}$(800nm/150nm) diaphragm. The proposed planar-type microsensor could be fabricated by simple silicon process using only 3 masks for photolithography process compared with 5 or 6 masks of the typical micro-gas sensor. The thermal properties of the microsensor from thermal simulation were compared with those of the fabricated microheater. Although there are some discrepancy between the simulation result and the result from the fabricated microheater, the thermal simulation by FEM was proved to be an useful method to evaluate the thermal properties of microheater. The sensing characteristics of the fabricated microsensor with the planar-type heater were investigated also.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.29-34
• /
• 2008

In this paper, we investigated electrical and physical characteristics of nickel silicide using rare-earth metals(Er, Yb, Tb, Dy), Incorporated Ytterbium into Ni-silicide is proposed to reduce work function of Ni-silicide for nickel silicided schottky barrier diode (Ni-silicided SBD). Nickel silicide makes ohmic-contact or low schottky barrier height with p-type silicon because of similar work function (${\phi}_M$) in comparison with p-type silicon. However, high schottky barrier height is formed between Ni-silicide and p-type substrate by depositing thin ytterbium layer prior to Ni deposition. Even though the ytterbium is deposited below nickel, ternary phase $Yb_xN_{1-x}iSi$ is formed at the top and inner region of Ni-silicide, which is believed to result in reduction of work function about 0.15 - 0.38 eV.