• The Journal of the Acoustical Society of Korea
• /
• v.22 no.8
• /
• pp.652-659
• /
• 2003

High-frequency(40∼120 kHz) reflection loss measurements on the water-sandy sediment with a flat interface were conducted in a water tank for various grazing angles. The water tank(5×5×5 m) was filled with a 0.5 m-thick-flat bottom of 0.5ø-mean-grain-size sand. Reflection losses, which were experimentally obtained as a function of grazing angle and frequency, were compared with the forward loss model, APL-UW model (Mourad & Jackson, 1989). For frequencies below 60 kHz, the observed losses well agree with the reflection loss model, however, in cases for frequencies above 70 kHz, the observed losses are greater by 2∼3 dB than the model results. The model calculation, which does not fully account for the vertical scale of roughness due to grain size, produce less bottom losses compared to the observations that correspond to large roughness based on the Rayleigh parameter in the wave scattering theory. In conclusion, for the same grain-size-sediment, as frequencies increase, the grainsize becomes the scale of roughness that could be very large for the frequencies above 70 kHz. Therefore, although the sea bottom was flat, we have to consider the frequency dependence of an effect of roughness within confidential interval of grain size distribution in reflection loss model.

• The Journal of Engineering Geology
• /
• v.19 no.1
• /
• pp.71-79
• /
• 2009

Step-drawdown tests were conducted at four pumping Wells, two in porous media and two in fractured rocks, respectively. In general, P = 2.0 suggested by Jacob (1947) is applied to porous media and fractured rocks in terms of drawdowns of step-drawdown test. In an attempt to review problems of linear model (Jacob's graphic method) in interpreting the step-draw down test, the outcomes of well parameters (aquifer loss coefficient (B), well loss coefficient (C) and well loss exponent (P)) calculated from linear and nonlinear model (Labadie and Helweg's least-squares method) were compared and analyzed. The values of C and P calculated from linear and nonlinear models differed according to permeability of aquifer and the conditions of pumping well. The value C obtained from nonlinear models in porous media and fractured rocks is about $10^0{\sim}10^{-2}$ and $10^{-3}{\sim}10^{-6}$ times lower than in their linear models, respectively. The value P of porous media obtained from nonlinear model ranged from 2.123 to 2.775, while it ranged from 3.459 to 5.635 for fractured rocks. In case of nonlinear model, well loss highly depends on the value P. At this time, well efficiencies calculated from linear and nonlinear models were $1.56{\sim}14.89%$ for porous media and $8.73{\sim}24.71%$ for fractured rocks, showing a significant error according to chosen models. In nonlinear model, it was found that the regression analysis using the least squares method was very useful to interpret step-drawdown test in all aquifer.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.46 no.5
• /
• pp.82-92
• /
• 2018

The purpose of this study is to develop a model for the density management of planting sites and an additional model for new planting sites. In the Dongtan New Town of Hwaseong, there are buffer green spaces, with widths between 8m and 15m, between roads and apartment complexes. A total 38 survey plots were set to examine the planting patterns and the density of landscape trees. The Crown Overlapping Index (COI) was developed to assess the level of overcrowding as far as tree growth and development effectively. Pinus strobus recorded the most serious level of overcrowding growth and development. Its average density and average COI were very high at $0.3trees/m^2$ and 35.6%, respectively. There were many areas in which its COI was above 45%. The criteria for density management were set by standardizing the COI into three levels, which were above 45% (Type A), 30~45% (Type B), and under 30% (Type C). A model was proposed to manage poorly growing trees and to develop a model to select and manage trees of similar specification based on the planting patterns. The trees of density management areas were reviewed in terms of tree types and the ease of transplanting to establish an application system for the management plans according to the possibility of transplanting, thinning, and pruning. In new buffer green spaces, the planting density of Pinus strobus was lowered to $0.20{\sim}0.25trees/m^2$, with that of shrubs being reduced to $1.5{\sim}2.0trees/m^2$, leading to a planting design model to cover the lower parts in at least 30~40%.

• Journal of Korean Society of Transportation
• /
• v.23 no.3 s.81
• /
• pp.95-108
• /
• 2005

The purpose of this study is to develop the ITS evaluation model using the Probabilistic Risk Analysis (PRA) methodology and to demonstrate the goodness-of-fit of the large ITS projects through the comparative analysis between DEA and PRA model. The results of this study are summarized below. First, the evaluation mode] using PRA with Monte-Carlo Simulation(MCS) and Latin-Hypercube Sampling(LHS) is developed and applied to one of ITS projects initiated by local government. The risk factors are categorized with cost, benefit and social-economic factors. Then, PDF(Probability Density Function) parameters of these factors are estimated. The log-normal distribution, beta distribution and triangular distribution are well fitted with the market and delivered price. The triangular and uniform distributions are valid in benefit data from the simulation analysis based on the several deployment scenarios. Second, the decision making rules for the risk analysis of projects for cost and economic feasibility study are suggested. The developed PRA model is applied for the Daejeon metropolitan ITS model deployment project to validate the model. The results of cost analysis shows that Deterministic Project Cost(DPC), Deterministic Total Project Cost(DTPC) is the biased percentile values of CDF produced by PRA model and this project need Contingency Budget(CB) because these values are turned out to be less than Target Value(TV;85% value), Also, this project has high risk of DTPC and DPC because the coefficient of variation(C.V) of DTPC and DPC are 4 and 15 which are less than that of DTPC(19-28) and DPC(22-107) in construction and transportation projects. The results of economic analysis shows that total system and subsystem of this project is in type II, which means the project is economically feasible with high risk. Third, the goodness-of-fit of PRA model is verified by comparing the differences of the results between PRA and DEA model. The difference of evaluation indices is up to 68% in maximum. Because of this, the deployment priority of ITS subsystems are changed in each mode1. In results. ITS evaluation model using PRA considering the project risk with the probability distribution is superior to DEA. It makes proper decision making and the risk factors estimated by PRA model can be controlled by risk management program suggested in this paper. Further research not only to build the database of deployment data but also to develop the methodologies estimating the ITS effects with PRA model is needed to broaden the usage of PRA model for the evaluation of ITS projects.

• Korea journal of population studies
• /
• v.16 no.2
• /
• pp.65-83
• /
• 1993

The purpose of this study is estimate limits of Korean life expectancy at birth by 'Gompertz growth curse Model', 'Cause-Elimination Model' and Multidimensional models of Senescencee and Mortality'. Data used in Gompertz curve were obtained from all life tables published from 1905 to 1990 in Korea, and life expectancies at birth of eighteen groups were selected at five-year interval in consideration of time-series changes. Data used in Cause-Elimination Model are 'Cause of Death statistics in 1991' published in 1992 by National Bureau of Statistics of Korea and 'life table of 1989' published in 1990 by National Bureau of Statistics, Economic Planning Board of Korea. The materials are all classifiable death data, 119, 253 cases of male and 82, 420 cases of female, which is from 1991 Causes of Death statistics. The cases of death analyzed belong to one of 8 categories; i.e., Infectious and Parasitic Diseases(001-139; with notation of Infectious Diseases), Malignant Neoplasms(140-208), Hypertensive Diseases(401-405), Ischemic Heart Dieases and Diseases of Pulmonary Circulation and Other Forms of Heart Diseases(410-429;with notation of Heart Disease), Cerebrovascular Diseases(430-438), Chronic Liver Diseases and Cirrhosis(571; with notation of Liver Diseases), Injury and Poisoning(800-999) and all other disease. Data used in 'Multidimensional models of senescence and mortality' were life table of 1989 published by National Bureau of statistics, Economic Planning Board of Korea and life table of 1970, 1978-79, 1983, 1985 and 1987. The major findings may be summarised as follows: 1. Estimate equations of Gompertz growth curve using life expectancy at birth during the 1905-1990 period are as the following. Male : y = 88.047697 $\times$ $0.199690^{0.903381x}$ Female : y = 95.632828 $\times$ $0.199690^{0.903381x}$ Limits of life expectancy at birth, which were estimated by Gompertz growth curve, are 88.05 for male and 95.63 for female. 2. The effect on life expectancy at birth eliminationg all causes death is 14.04 years(for male) and 10.86 years(for female). Astonishingly, eliminating the malignant neoplasms increase life expectancy at birth by 2.85 years for male 2.03 years for female in 1991. In table 8 we show the effect on life expectancy at birth of separately eliminating each of the 8 categorical causes of death. The theoretical limit to life expectancy by Cause-Elimination Model is 80.96 for male and 85.82 for female. 3. If the same rate of delay [0.376 year(male), 0.435 year(femable) per calendar year] continued, then life expectancy at birth would reach 74.82(male) years and 84, 10(female) years in 2010. With 14.04-years(male) and 10.86-years(female) effect attributable in 2010 would be 88.86 years(male) and 94.96(femable) years. 4. 'Multidimensional models of senescence and death' permits calculations of the value of the attribution coefficient (B), percent of loss per year of physiologic function. The results of Ro and B during the 1970-1989 period are listed in table 9. Estimate of limit to Korean life expectancy at birth by 'Multidimensional models of senescence and death' is 99.47 years for male and 104.74 years for female in 1989.

• Ocean and Polar Research
• /
• v.38 no.2
• /
• pp.89-102
• /
• 2016

In this study, we evaluated the model performance with respect to Sea Surface Temperature (SST) and Net Heat Flux (NHF) by considering the characteristics of seasonal temperature variation and contributing factors and by analyzing heat budget terms in the Northwestern Pacific and East Asian Marginal Seas ($110^{\circ}E-160^{\circ}E$, $15^{\circ}N-60^{\circ}N$) using the HadGEM2-AO historical run. Annual mean SST of the HadGEM2-AO is about $0.065^{\circ}C$ higher than observations (EN3_v2a) from 1950 to 2000. Since 1960, the model has simulated well the long-term variation of SST and the increasing rate of SST in the model ($0.014^{\circ}C/year$) is comparable with observations ($0.013^{\circ}C/year$). Heat loss from the ocean to the atmosphere was simulated slightly higher in the HadGEM2-AO than that in the reanalysis data on the East Asian Marginal Seas and the Kuroshio region. We investigated the causes of temperature variation by calculating the heat budget equation in the two representative regions. In the central part of the Kuroshio axis ($125^{\circ}E-130^{\circ}E$, $25^{\circ}N-30^{\circ}N$: Region A), both heat loss in the upper mixed layer by surface heat flux and vertical heat advection mainly cause the decrease of heat storage in autumn and winter. Release of latent heat flux through the heat convergence brought about by the Kuroshio contributes to the large surface net heat flux. Positive heat storage rate is mainly determined by horizontal heat advection from March to April and surface net heat flux from May to July. In the central part of the subtropical gyre ($155^{\circ}E-160^{\circ}E$, $22^{\circ}N-27^{\circ}N$: Region B), unlike Region A, vertical heat advection predominantly causes the decrease of heat storage in autumn and winter. In spring and summer, surface heat flux contributes to the increase of heat storage in Region B and the period is two times longer than the period for Region A. In this season, shoaling of the mixed layer depth plays an important role in the increase of SST.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.31 no.4
• /
• pp.317-330
• /
• 2021

Objectives: By law, companies in Korea must periodically measure workers' exposure to harmful chemicals (the system is called the Work Environment Monitoring Program (WMP)[a]) and report the results to the government. The government also measures exposure to monitor the WMP's reliability (called Reliability Assessment (RA) for WMP[b]). The issue is that measured data from these two sources are so different that the objectivity of WMP needs to be confirmed by comparing the results using the European Centre for Ecotoxicology and Toxicology of Chemicals' Targeted Risk Assessment (ECETOC TRA). Methods: Step 1: Data collection from WMP reports submitted by companies (n=586) and RA for WMP written by the government (n=33). Step 2: Data Standardization by key information included. Step 3: Data conversion to input-variables required to run the ECETOC TRA model, and run the model with specific data (n=514) which meet the predetermined exposure scenario. Step 4: Statistical data analysis by process category (PROC) and ventilation type from each source ([A] and [B]). Step 5: Additional analysis of any unexpected results. Results: The process categories of the production and handling of Dichloromethane were classified into 12 PROCs, and ten of them were selected to run ECETOC TRA. Modeled values tended to be higher than measured values from both sources. For the measured values from WMP, RCR distribution by PROC was narrow (0.197-0.267, 95% CI) and did not have a relationship with ventilation type, which differs from the tendency of the modeling result. Meanwhile, the measured values from RA for WMP were relatively widely distributed (0.301-1.177, 95% CI) by PROC. In particular PROCs (13,19) were high enough to exceed 1. Also, they become low with better ventilation types and appear differently depending on the ventilation type, similar to the model result. Conclusions: This study revealed that ECETOC TRA might have the potential to serve as a screening tool for exposure assessment and to be used as assistive method for WMP to estimate exposure. Further empirical study is required to confirm its availability as a screening tool.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.3B
• /
• pp.193-201
• /
• 2012

In the last decade, heavy rainfall induced debris flow events have been remarkably occurred in Korea. Consequently, debris flow is becoming one of the most dangerous natural phenomena in mountainous area. Understanding and correct predicting of the runout distance of debris flow is an essential prerequisite for developing debris flow hazard map and prevention technology. Based on the simple and widely used sled model, in this study, we analyse the net efficiency of debris flows which is a dimensionless constant (=1/R) and defined by the ratio of the horizontal runout distance L from the debris flow source to deposit and the vertical elevation H of the source above the deposit. The analysis of field data observed in total 238 debris flow events occurred from 2002 to 2011 reveals that the representative value of the net efficiency of debris flows in Korea is 4.3. The data observed in Gangwon province where is the most debris flow-prone area in Korea shows that debris flows in Inje area have the runout distance longer than those in Pyongchang and Gangneung. Overall features of the net efficiency of debris flows observed in the central Korea are similar to those in the southern Korea. The estimation based on aerial photographs and available depositional conditions appears to overestimate the net efficiency compared to estimation based on the field observations, which indicates that appropriate depositional conditions need to be developed for debris flows in Korea.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.10
• /
• pp.979-988
• /
• 2012

The 3D structure of GDL for fuel cells was measured using high-resolution X-ray tomography in order to study material transport in the GDL. A computational algorithm has been developed to remove noise in the 3D image and construct 3D elements representing carbon fibers of GDL, which were used for both structural and fluid analyses. Changes in the pore structure of GDL under various compression levels were calculated, and the corresponding volume meshes were generated to evaluate the anisotropic permeability of gas within GDL as a function of compression. Furthermore, the transfer of liquid water and reactant gases was simulated by using the volume of fluid (VOF) and pore-network model (PNM) techniques. In addition, the simulation results of liquid water transport in GDL were validated by analogous experiments to visualize the diffusion of fluid in porous media. Through this research, a procedure for simulating the material transport in deformed GDL has been developed; this will help in optimizing the clamping force of fuel cell stacks as well as in determining the design parameters of GDL, such as thickness and porosity.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.8
• /
• pp.677-685
• /
• 2014

A direct carbon fuel cell (DCFC) generates electricity directly by converting the chemical energy in coal. In particular, a DCFC system with a solid oxide electrolyte and molten carbonate anode media has been proposed by SRI. In this system, however, there are conflicting effects of temperature, which enhances the ion conductivity of the solid electrolyte and reactivity at the electrodes while causing a stability problem for the anode media. In this study, the effect of temperature on the stability of a carbon-carbonate mixture was investigated experimentally. TGA analysis was conducted under either nitrogen or carbon dioxide ambient for $Li_2CO_3$, $K_2CO_3$, and their mixtures with carbon black. The composition of the exit gas was also monitored during temperature elevation. A simplified reaction model was suggested by considering the decomposition of carbonates and the catalyzed Boudouard reactions. The suggested model could well explain both the measured weight loss of the mixture and the gas formation from it.