• 한국ITS학회:학술대회논문집
• /
• 2008.11a
• /
• pp.181-184
• /
• 2008

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.73.2-73.2
• /
• 2005

• 한국ITS학회:학술대회논문집
• /
• 2005.11a
• /
• pp.241-244
• /
• 2005

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2073-2075
• /
• 2004

본 논문에서는 nonradiative dielcctric (NRD) 도파로를 이용하여 28GHz대에서의 single balanced mixer를 설계하였다. 혼합기에 필요한 $90^{\circ}$ hybrid direction기 3dB 결합기를 NRD 도파로를 이용하여 설계 하였고 CST MWS를 이용하여 설계 결과를 검중 하였으며 결과는 중심 주파수 28GHz에서 대역폭이 1GHz의 결합기를 설계하였음을 확인할 수 있었다. 이와동시에 다이오드를 부착하기 위해 NRD 도파로와 마이크로스트립의 매칭 구조를 1 pole UDR과 patch를 이용하여 혼합기를 설계, 제작하였다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.12
• /
• pp.1018-1027
• /
• 2003

This study treats the analysis of the performance and the design of plume abatement wet/dry cooling tower with dry type heat exchanger using a numerical method. A two-dimensional analysis is performed using the finite volume method for mechanical draft counterflow and crossflow tower. For a coupling problem between water and air system, a turbulent two phase flow is considered. Effectiveness-NTU method is used for modeling of the dry type heat exchanger. The parameter change simulations of the outer wall shape, the relative flowrate of air, and attachment of an air mixer are performed to examine the effect on plume abatement. It is found that if the relative air flowrate ratio and the adequate air mixer type are chosen well in addition to the ratio of water to air flowrate, the loss of the cooling capacity and the additional cost are reduced and the plume is abated.

• Journal of electromagnetic engineering and science
• /
• v.8 no.3
• /
• pp.114-118
• /
• 2008

Direct-conversion RF front-end for 5-GHz WLAN is implemented in $0.18-{\mu}m$ CMOS technology. The front-end consists of a low noise amplifier, and low flicker noise down-conversion mixers. For the mixer, an inductor is included to resonate out parasitic tail capacitances in the transconductance stage at the operating frequency, thereby improves the flicker noise performance of the mixer, and the overall noise performance of the front-end. The receiver RF front-end has 6.5 dB noise figure, - 13 dBm input IP3, and voltage conversion gain of 20 dB with the power consumption of 30 mW.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.27-30
• /
• 2005

In a microfluidic chips pressure driven flow or electro-osmotic flow has been usually employed to deliver bio-samples. Flow in the chips is usually slow and the mixing performance is poor. A micro-mixer with a rapid mixing is important for practical applications. In this study a newly designed and electro-osmotic driven micro-mixer is proposed. This design is comprised of a channel and a series of metal electrodes periodically attached on the side surface. In this configuration electro-osmotic flows and the stirring effects are simulated three-dimensionally using a commercial code, CFD-ACE. Focus is given the effect on the electro-osmotic flow characteristics under the local variation of the electric field.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2006.07a
• /
• pp.718-718
• /
• 2006

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.139-142
• /
• 2000

In this paper, we designed a Self-Oscillating mixer(SOM) for Microwave Transceiver. Implemention of SOM shows the output power of 4.33dBm at 10.750Hz and the phase-noise of -102dBc/Hz at 100KHZ offset frequency, Applying the input frequency band 11.7GHz∼12.9GHz, The designed SOM If frequency is 950MHz∼2150MHz and its conversion gain is 6dB in the If band. We convinced that SOM is applied to a digital transceiver down-converter

• 한국전산유체공학회:학술대회논문집
• /
• 2006.10a
• /
• pp.159-162
• /
• 2006

In the microfluidics devices the most important thing is mixing efficiency of various fluids. In this study a newly designed mixer is proposed to enhance the mixing effect with the purpose to apply it to microchannel mixing in a short future. This design is composed of a channel with cross baffles periodically arranged on the both bottom and top surfaces of the channel. To obtain the flow patterns, the numerical computation was performed by using a commercial code, ANSYS CFX 10.0. To evaluate the mixing performance, we computed Lyapunov exponent and obtained Poincare sections.