• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.2
• /
• pp.20-26
• /
• 2012

Recently, micromilling process has been progressed to meet the variety of the industry demands in micromolds and precision components. As a result, more and more commercialized micro tools and machines become available during last few years. This paper reviews the recent progress of micromilling technology in last five years. The results in process, machine tools, and micro tool fabrications are discussed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.647-648
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.1035-1036
• /
• 2009

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.23 no.4
• /
• pp.686-697
• /
• 1994

The hardness of hard red winter (HRW) wheat had an effect on the yield of farina , as it positively correlated with the coarse fraction (over 34W) and negatively correlated with the flour fraction from farina milling. But it did not show any significances on flour milling from the micromilling process. The flour yields was better correlated with the break flour fraction (r=0.730 than with reduction flour (r=0.27). The farina yield was controlled by a fraction over 34W (coarse granule0. Protein was the most important single factor for the quality of cooked farina spaghetti, but not for flour milling or farina milling. On the other hand, hardness was important in the production of farina milling , whereas it did not govern spaghetti cooking quality, Environmental factors affected the quality of cooked spaghetti as much as varieties of HRW wheats. The quality of cooked farina spaghetti generally correlated with the protein in the location composites of wheats. Higher protein content wheats showed better spaghetti cooking quality.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.299-300
• /
• 2008

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.2
• /
• pp.70-77
• /
• 2007

The application of focused ion beam(FIB) technology has been broadened in the fabrication of nanoscale regime. The extended application of FIB is dependent on complicated reciprocal relation of operating parameters. It is necessary for successful and efficient modifications on the surface of silicon substrate. The primary effect by Gaussian beam intensity is significantly shown from various aperture size, accelerating voltage, and beam current. Also, the secondary effect of other process factors - dwell time, pixel interval, scan mode, and pattern size has affected to etching results. For the process analysis, influence of the secondary factors on FIB micromilling process is examined with respect to sputtering depth during the milling process in silicon material. The results are analyzed by the ratio of signal to noise obtained using design of experiment in each parameter.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1793-1797
• /
• 2003

After the micro turning lathe was developed in the last year by AMR Laboratory in Yeungnam university, a micromilling machine is developed for micro/meso machining. This machine is integrated with PZT-driven micro-sliders, micro-linear encoders, aerostatic spindle which has maximum 150,000 rpm. It is applicable to milling and drilling of micro scale. This paper presents the possibility of micro/meso machining and characteristics of micro end milling process by using micro machine. A machining of micro parts using 0.2 mm flat end mill was achieved by micro-milling machine. Experimental results show the machining capability and positional accuracy of this machine is good enough for machining micro parts.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.6
• /
• pp.401-409
• /
• 2016

The formation of micro-burrs in micro-milling processes causes several problems related to productivity and surface integrity. It should be minimized and suppressed by effective monitoring of the cutting conditions. This paper presents the correlation between the micro-burr length and cutting signals in the micro-milling process of an Al alloy (Al6061-T6). The acoustic emission (AE) signals and cutting force signals are acquired during the experiments. The characteristics of the cutting signals are obtained by analyzing the AE root mean square value and resultant cutting force. In addition, the micro-burr length is measured according to the cutting conditions by analyzing a scanning electron microscopy image of the machined surface. The results of this study can be used to enhance the surface quality of micro parts.