• Korean Journal of Metals and Materials
• /
• 제49권12호
• /
• pp.930-936
• /
• 2011

In the present study, we show that the addition of Ag, an element having a positive enthalpy of mixing with Cu in the liquid state, enables the simultaneous enhancement of the glass forming ability and the plasticity in Cu-Zr-Ag bulk metallic glasses (BMGs). Rods of 4 mm diameter could be prepared with a fully amorphous structure and values of plastic strain up to 18% were measured under a compression mode for compositions around $Cu_{42.5}Zr_{47.5}Ag_{10}$. The possible role of Ag in the change of the atomic structure and the enhancement of the plastic strain in the ternary Cu-Zr-Ag BMGs is discussed based on analyses from transmission electron microscopy and EXAFS (extended X-ray absorption fine structure).

• Journal of the Microelectronics and Packaging Society
• /
• 제29권1호
• /
• pp.43-47
• /
• 2022

In this study, we demonstrated an eco-friendly thin-metallic-film-based heater which can be operated in water. Based on the materials stability, Mo was selected as the heating element to secure long-term stability. Using a magnetron sputtering, 40 nm-thick Mo layers were deposited onto a glass substrate, followed by the deposition of 60-nm-thick ZnO layer to prevent oxidation during the heater fabrication process. Then, PVB (Polyvinyl Butyral) was applied on top of ZnO layer and an additional glass substrate was placed, which were heated at 150℃ for 2 hr. The PVB was cured with strong adhesion by the processing condition. We operated the Glass/Mo/ZnO/Glass heater in water, and it was shown that the water temperature reached 50℃ within 2 minutes, with a minimal resistance change of the heater. Finally, the heaters exhibit a semi-transparency, and this aesthetic advantage is expected to contribute to the added value of the heater.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.271-272
• /
• 2012

Bulk Metallic Glasses (BMGs or amorphous alloy) exhibit high strength and good corrosion resistance. Applications of thin films and micro parts of BMGs have been used a lot since its inception in the research of BMGs. However, Application and fabrication of BMGs are limited to make structural materials. Thin films of BMGs which is sputtered on the surface of structural materials by sputtering process is used to improve limits about application of BMGs. In order to investigate the difference of properties between designed alloys and thin films, we identified that thin films deposited on the surface that have the characteristic of the amorphous films and the composition of designed alloys. Zr-Cu (Cu=30, 35, 38, 40, 50 at.%) and Zr-Cu-Al (Al=10 at.% fixed, Cu=26, 30, 34, 38 at.%) alloys were fabricated with Zr (99.7% purity), Cu (99.997% purity), and Al (99.99% purity) as melting 5 times by arc melting method before rods 2mm in diameter was manufactured. In order to analyze GFA (Glass Forming Ability), rods were observed by Optical Microscopy and SEM and $T_g$, $T_x$, ($T_x$ is crystallization temperature and $T_g$ is the glass transition temperature) and Tm were measured by DTA and DSC. Powder was manufactured by Gas Atomizer and target was sintered using powder in large supercooled liquid region ($=T_x-T_g$) by SPS(Spark Plasma Sintering). Amorphous foil was prepared by RSP process with 5 gram alloy button. The composition of the foil and sputtered thin film was analyzed by EDS and EPMA. In the result of DSC curve, binary alloys ($Zr_{62}Cu_{38}$, $Zr_{60}Cu_{40}$, $Zr_{50}Cu_{50}$) and ternary alloys ($Zr_{64}Al_{10}Cu_{26}$, $Zr_{56}Al_{10}Cu_{34}$, $Zr_{52}Al_{10}Cu_{38}$) have $T_g$ except for $Zr_{70}Cu_{30}$ and $Zr_{60}Al_{10}Cu_{30}$. The compositions with $T_g$ made into powders. Figure shows XRD data of thin film showed similar hollow peak.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• 제18권3호
• /
• pp.285-293
• /
• 2009

Thermal infrared cameras have been conducted actively in various application areas, such as military, medical service, industries and cars. Because of their characteristic of sensing the radiant heat emitted from subjects in the range of long-wavelength($3{\sim}5{\mu}m$ or $8{\sim}12{\mu}m$), and of materializing a vision system, when general optics materials are used, they don't react to the light in the range of long-wavelength, and can't display their optic functions. Therefore, the materials with the feature of higher refractive index, reacting to the range of long-wavelength, are to be used. The kinds of materials with the characteristic of higher refractive index are limited, and their features are close to those of metals. Because of these metallic features, the existing producing method of optical systems were direct manufacturing method using grinding method or CAD/CAM, which put limit on productivity and made it difficult to properly cope with the increasing demand of markets. GASIR, a material, which can be molded easily, was selected among infrared ray optics materials in this study, and the optical system was designed with two Aspheric lenses. Because the lenses are molded in the environment of high temperature and high pressure, they require a special metallic pattern. The metallic pattern was produced with materials with ultra hardness that can stand high temperature and high pressure. As for the lens mold, GMP(Glass Molding Press) of the linear transfer method was used in order to improve the productivity of optical systems for thermal infrared cameras, which was the goal of this paper.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제36권6호
• /
• pp.591-598
• /
• 2012

In this study, the cutting characteristics of bulk metallic glass (BMG) cut using a computer numerically controlled (CNC) lathe were investigated for different insert tool materials and cutting speeds. The surface roughness, chip morphology, cutting forces, and tool wear during turning of $Zr_{50}Cu_{40}Al_{10}$ BMG alloy were examined. Four kinds of tool materials were used to cut an 8-mm-diameter BMG. The examination of the surface roughnesses of the BMG specimens machined at each cutting speed showed that the surface roughness became better as the cutting speed increased, and the tool materials also influenced the surface roughness. The chip morphology investigations showed that the unoxidized BMG chips had serrated curled chips with adiabatic shear bands, while the oxidized chips exhibited local melting and tangling rather than the usual spiral-shaped chips. The cutting force induced during machining of the Zr-based BMG was the largest for the TiN-WC tool, followed by the polycrystalline diamond (PCD) tool. The cermet tool exerted the smallest cutting force.

• Journal of the Optical Society of Korea
• /
• 제7권3호
• /
• pp.160-164
• /
• 2003

Materials processing by ultrashort pulsed laser is actively being applied to micromachining technology due to its advantages with regard to non-thermal machining. In this study, materials processing with ultrashort pulses was studied by using the high repetition rate of a 800 nm Ti:sapphire regenerative amplifier. This revealed that the highly precise micromachining of metallic thin film and bulk glass with a minimal heat affected zone (HAZ) could be obtained by using near damage threshold energy. Grooves with diffraction limited sub-micrometer width were obtained with widths of 620 nm on Cr thin film and 800 nm on a soda-lime glass substrate. The machined patterns were investigated through SEM images. We also phenomenologically examined the influence of variations of parameters and proposed the optimal process conditions for microfabrication.

• Applied Microscopy
• /
• 제45권2호
• /
• pp.58-62
• /
• 2015

Formation of an icosahedral phase in the bulk glass forming $Ti_{40}Zr_{29}Be_{14}Cu_9Ni_8$ alloy during crystallization from amorphous phase and solidification from melt is investigated. The icosahedral phase with a size of 10 to 15 nm forms as a thermodynamically stable phase at intermediate temperature during the transformation from amorphous to crystalline phases such as Laves and ${\beta}$-(Ti-Zr) phases, indicating that the existence of the icosahedral cluster in the undercooled liquid. On the other hand, the icosahedral phase forms as a primary solidification phase even though the Laves phase is stable at high temperature, which is can be explained based on the high nucleation rate of icosahedral phase relative to that of competing crystalline Laves phase due to lower interfacial energy between icosahedral and liquid phases.

• Journal of the Korean Society of Industry Convergence
• /
• 제10권4호
• /
• pp.213-219
• /
• 2007

Glass-to-metal contact should be prevented in the design of any structural glass component. Because glass is extremely brittle and will fracture readily if even a small point load is applied. If the assembly includes a glass component supported by metallic structure, designers should provide a pliable interface of some kind between the two parts. But there happens high demand of glass-to metal contact in semiconductor industries due to adoption of dry cleaning process as one of the good solution to reduce running cost - carry out equipments cleaning with high corrosive and etching gas such as CF4 with keeping process temperature as the same as high service temperature. Therefore the quartz glass have to be received compression by direct contact with metal as the form of weight itself and vacuum pressure and fatigue by vibrations caused by process during the process. In this paper investigation will be carried out on fracture behavior of quartz glass contacted with metal directly under local load and fatigue given by process vibration with apparatus which can give $lox{\backslash}cal$ load and vibration through PZT ceramics to give guideline to prevent unintended fracture of quartz glass.

• Journal of Conservation Science
• /
• 제7권1호
• /
• pp.23-30
• /
• 1998

The examination of scientific analysis could give many information on the object of ancient glass. It would be allowed to understand the cultural situation and a course of inflow that the data of glass composition was classified by raw materials, technique of making, period and regional groups. Quantitative analysis conditions for SEM-EDS were set for glass and glaze on the pottery and 62 samples of glass beads excavated from Yangdong-ri remains at Kimhae were analyzed and classified. It was found that the glass beads were made of all alkali-glass. In addition, it was postulated that the potash glass was appeared from the 1st century A.D. and soda glass was appeared from the late second or early 3rd century A.D. in this region. The colors of glass were closely related to the concentration of metallic elements such as copper, iron and manganese. It was confirmed that the composition of glass beads could be classified and characterized by raw materials, color, period and regional groups.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• 제10권1호
• /
• pp.104-114
• /
• 2000

This study was carried out to estimate current status of dust concentrations in the factories producing non-metallic products in Korea. Data were gathered from the environmental monitoring reports by 40 workplace environmental monitoring institutes and the questionnaire designed for the study by the authors. A total of 1838 dust samples from 368 plants were obtained from the reports and were analyzed with no data modifications. But data on asbestos, rock wool, and welding fumes were excluded in this evaluation. The factories were classified into eight groups according to the standard industrial classification scheme in Korea. The results of this study were as follows; 1. The factories included were glass, non-refractory ceramic, refractory ceramic ware, structural non-refractory clay and ceramic, cement and lime, articles of concretes, and stone. Mean(geometric mean) concentrations of total dust samples ranged from $1.75(0.84)mg/m^3$ to $5.87(2.84)mg/m^3$. Statistically significantly higher dust concentrations were found in the cement and lime industries compared with other industries. 2. The non-compliance rates were 15.2% in glass and 20.6% in other non-metallic mineral products industries. Although all institutions surveyed utilized the identical sampling and classification scheme for dusts as specified in the current occupational exposure limits, wide discrepancies were found in collecting samples and classifying dusts. Further problems were discovered in classifying dusts. A dust sample collected could be classified into any of the three groups regardless of silica content. The results of this study showed that dust concentrations in the non-metallic products industries varied widely. Also discovered was classification errors of dust types among workplace monitoring institutes. These errors could adversely affect the results of exposure assessments and the true nature of dust hazards. Further, no institutions performed respirable dust sampling and analysis of crystalline silica. In order to correct these malpractices, current standards of occupational exposure limits should be revised and tight supervision by the Ministry of Labour be suggested.