• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.27 no.1
• /
• pp.56-62
• /
• 2015

The potential impact of water temperature on sea level and air temperature rise in response to recent global warming has been noticed. To predict the effect of temperature change on river water quality and aquatic environment, it is necessary to understand and predict the change of water temperature. Air-water temperature relationship was analyzed using air temperature data at Buan and water temperature data of Shinsi, Garyeok, Mangyeong and Dongjin. Maximum and minimum water temperature was predicted by neural network and the results show a very high correlation between measured and predicted water temperature.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.4
• /
• pp.498-504
• /
• 2012

The water-cooled Permanent Magnet Linear Synchronous Motor (PMLSM) has a wide range of applications due to high efficiency, high thrust force density and high acceleration. In order to ensure normal operation and maximum output, both the magnetic and thermal performance are vital to be considered. Based on ANSYS software, electromagnetic and thermal finite-element analysis (FEA) models of a 14-pole, 12-slot water-cooled PMLSM are erected adopting suitable assumptions. Firstly, the thrust force and force ripple with different current densities are calculated. Secondly, the influence of different water flow on the motor heat dissipation and force performance under different operationional conditions are investigated and optimized. Furthermore, for continuous operation, the temperature rise and thrust feature are studied under the rated load 8A, the proper temperature $120^{\circ}C$ and the limited temperature $155^{\circ}C$. Likewise, for short-time operation, the maximum duration is calculated when applied with a certain large current. Similarly, for intermittent operation, load time as well as standstill time are determined with the optimal current to achieve better thrust performance.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.13 no.1
• /
• pp.40-46
• /
• 2010

In urban area, inversion layer prevents air pollutants from being dispersed. To determine nocturnal inversion characteristics at SookMyung Girls' High School near high-rise residential commercial complex buildings in Seoul, air temperature and humidity data were observed at 10minute interval from December 1st, 2007 to May 2nd, 2008. Temperature-Humidity (T-H) sensors were installed at SMG (SookMyung_Ground) and SMR (SookMyung_Roof), and then these two data were compared, analyzed and examined to illustrate air temperature differences of SMG and SMR. After the analysis, the maximum nocturnal inversion was observed by $3.3^{\circ}C$ at 18:10 on December 26th 2007, at that time the weather condition was clear and weak wind. Nocturnal inversions began 2-3 hours before sunset and it reached maximum inversion just after sunset and continued through nighttime until sunrise or 1-2 hours after sunrise. In terms of seasonal variation nocturnal inversions occurred dominantly in March and April rather than winter season.

• Journal of the Korean Solar Energy Society
• /
• v.35 no.4
• /
• pp.67-75
• /
• 2015

PV module is conventionally connected in series with some solar cell to adjust the output of module. Some bypass diodes in module are installed to prevent module from hot spot and mismatch power loss. However, bypass diode in module exposed outdoor is easily damaged by surge voltage. In this paper, we study the thermal and electrical characteristics change of module with damaged bypass diode to easily find module with damaged bypass diode in photovoltaic system consisting of many modules. Firstly, the temperature change of bypass diode is measured according to forward and reverse bias current flowing through bypass diode. The maximum surface temperature of damaged bypass diode applied reverse bias is higher than that of normal bypass diode despite flowing equal current. Also, the output change of module with and without damaged bypass diode is observed. The output of module with damaged bypass diode is proportionally reduced by the total number of connected solar cells per one bypass diode. Lastly, the distribution temperature of module with damaged bypass diode is confirmed by IR camera. Temperature of all solar cells connected with damaged bypass diode rises and even hot spot of some solar cells is observed. We confirm that damaged bypass diodes in module lead to power drop of module, temperature rise of module and temperature rise of bypass diode. Those results are used to find module with a damaged bypass diode in system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.830-833
• /
• 2004

Voltage step-down characteristics of Ring/Dot type piezoelectric transformer were examined with increasing input voltage from $10\;V_{pp}$ to $140V_{pp}$. Then the output load resistance was fixed to $125\;\Omega$. The voltage gain showed constant value till the input voltage of $70\;V_{pp}$. And then it linearly decreased till the input voltage of $140V_{pp}$. The output voltage of fabricated piezoelectric transformer increased with increasing input voltage. And driving frequencies when the output voltage was maximum value were changed according to input voltage. Frequency shifts and temperature rise of fabricated sample showed 2 kHz, $13^{\circ}C$, respectively when input voltage was changed from $10\;V_{pp}$ to $140V_{pp}$. Because of the temperature rise of fabricated piezoelectric transformer, the step-down characteristics of it was deteriorated above the input voltage of $70\;V_{pp}$.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.2 no.3
• /
• pp.95-102
• /
• 2000

The northward shift of the cultivation region of winter barley has been considered because of consecutive warm winters from the middle of 1980's. There was 1.02$^{\circ}C$ rise in mean air temperature during winter barley cropping season from 1975 to 1998. During this period, the maximum air temperature affected the mean air temperature rise rather than the minimum air temperature. The amount of mean precipitation was 513.3 mm during winter barley cropping season from 1975 to 1998 and was least in 1992. Sunshine hours has increased little by little in the all regions except rural regions. The air temperature during winter barley cropping season from 1987 to 1999 in which the winter was warm was higher than the normal air temperature(1961~1990). On the other hand, the air temperature during winter barley cropping season from 1974 through 1986 was similar to the normal air temperature. The amount of mean precipitation during winter barley cropping season from 1987 through 1999 was similar to the normal precipitation except April. During this period, the amount of mean precipitation of April was lower by 26 mm than the normal year(1961~1990). Sunshine hours during winter barley cropping season from 1987 to 1999 decreased generally in comparison with a normal year. Considering the air temperature rise during wintering from 1987 to 1998, it might be possible to extend the cropping area of winter barley northward.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.7
• /
• pp.1144-1150
• /
• 2016

Short-term load forecasting is essential to the electricity pricing and stable power system operations. The conventional weekday 24-hour load forecasting algorithms consider the temperature model to forecast maximum load and minimum load. But 24-hour load pattern forecasting models do not consider temperature effects, because hourly temperature forecasts were not present until the latest date. Recently, 3 hour temperature forecast is announced, therefore hourly temperature forecasts can be produced by mathematical techniques such as various interpolation methods. In this paper, a new 24-hour load pattern forecasting method is proposed by using similar day search considering the hourly temperature. The proposed method searches similar day input data based on the anomalous weather features such as continuous temperature drop or rise, which can enhance 24-hour load pattern forecasting performance, because it uses the past days having similar hourly temperature features as input data. In order to verify the effectiveness of the proposed method, it was applied to the case study. The case study results show high accuracy of 24-hour load pattern forecasting.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.3 no.2
• /
• pp.43-47
• /
• 1979

This paper presents the effect of stress relief annealing on mechanical properties in single Vee-groove welding joint. In this experiment, the investigation of annealing effect on mechanical properties of test material carried out by changing the annealing temperature from $600^{\circ}C$ to $900^{\circ}C$ under the given conditions. The results pbtained by this study are as follows: (1) Under the constant welding conditions, the tensile strength of test welded joint decrease in accordance with the increase of annealing temperature. The experimental results show that the reduction rate of tensile strength is about 35.09% of base metal strength. (2) Microhafdness distribution of welded joint bring about the maximum hardness near the bended line of welding joint. (3) Izod impact energy of welded joint in increase in according to the rise of annealing temperature and the peak energy of impact test occurs at $800^{\circ}C$

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.196-197
• /
• 2006

In this study, low temperature sintering multilayer piezoelectric transformer for DC-DC converter were manufactured using (PbCaSr)Ti(MnSb)$O_3$ ceramics and thin their electrical properties were investigated according to the vanation of frequency and load resistance. The voltage step-up ratio of multilayer piezoelectric transformer showed the maximum value m the vicinity of 1.3MHz and increased according to the increase of load resistance. When the output impedance coincided with the load resistance, the piezoelectric transformer showed the temperature rise of about $21^{\circ}C$ under the output power of 6W.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.98-101
• /
• 2001

Linear motor feature a direct connection to the machine tool, therefore a direct route for heat transfer. The heat dissipation of linear motor machine is affected by the maximum temperature rise of the primary part, coil and the cooling method. To minimize temperature induced dimension changes and decrements of performance, linear motor machine require effective cooling mechanism. To evaluate cooling performance of existing linear motor machine, some experiments about temperature profile are performed using thermocouple recorder. Due to the lack of information about internal structure, only some finite element modeling is prepared and analyzed.