• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.65-68
• /
• 1997

Vickers hardness is defined as indenting force per unit area indented by a pyramid-shaped diamond at the hardness test. It is well known that Vickers hardness has a direct relation with the flow stress of the strain-hardened material. This relation was theoretically investigated and the result was summerized in a form of algebraic equation in the last paper. In the present paper and experimental validation of this theoretical relation is given along with mathematical formulas for conversion of Vickers hardness into the flow stress in the strain-hardened material for practical use.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1992.10a
• /
• pp.75-86
• /
• 1992

The elevation of reclamation work in the coastal area for the industrial complex is determined through the investigation and review of marine conditions, drainage plan and fill materials. The embankment to be constructed with crushed stone on the soft soil should be safe against the wave force, immediate and long term consolidation settlement, overturning and sliding due to self-weight and other forces. Because of lack of fill material from the borrow pit, the soft marine clay to be dredged shall be used as the reclamation material. And Paper Drain Board is used as the improvement method for the deep soft clay strata.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1997.10a
• /
• pp.1-7
• /
• 1997

Equivalent thermal conductivities and elasticity properties of woven fabric composites are computed using homogenization technique. The computational results show that the strength and thermal conductivity linearly increase with fiber volume fraction and that the variations of undulation of fibers has little effect on equivalent material properties. Homogenization technique is proved useful in the study of woven fabric composites and may find a lot more applications in the area.

• Proceedings of the KSR Conference
• /
• 2002.10b
• /
• pp.851-856
• /
• 2002

In this study, the property against low velocity of the compesite material, which will be applied a rail vehicle, is shown using experiment and a finite element code. The property can be denoted the resistance of impact force, which is defined by maximum impact force over damage area. A damage propagation model is necessary to estimate accurately the impact property of a composite material through FEM code.

• CDE review
• /
• v.8 no.3
• /
• pp.40-51
• /
• 2002

Design and manufacturing (or production) must be closely interrelated. They should never be viewed as separate disciplines or activities. Each part or component of a product must be designed so that it not only meets design requirements and specifications, but also can be manufactured and assembled economically, ecologically and with relative ease. This approach improves productivity and allows a manufacturer to remain competitive. This broad view has become recognized as the area of design for manufacture and assembly(DFMA). Here the principles of the DFMA and their some examples are reviewed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.467-470
• /
• 1998

The scientiic and technological aspects of water-soluble and water-swelling polymers to be synthesized from the domestic raw materials of Kazakhstan are described. The application area of polymeric reagents in medicine, biotechnology, agriculture, enhanced oil recovery, ecology is also considered.

• Journal of Korean Dental Science
• /
• v.4 no.2
• /
• pp.79-84
• /
• 2011

The extracted right mandibular third molar of a 37-year-old man was transplanted into the first molar area, and a bone graft procedure using autogenous tooth-bone graft material was performed for the space between the root and the alveolar socket. Reattachment was achieved after 10 months. Therefore, autogenous tooth-bone graft material is considered reasonable for bone induction and healing in the autotransplantation of teeth.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1990.10a
• /
• pp.1-16
• /
• 1990

In this paper, a system to measure treeing degradation phenomena in organic insulating materials, using an image sensor, is discussed. Using an image processing technique, tree features immediately after tree initiation as well as changes in the configuration of the tree were measured. which up to now have been extremely difficult to observe by conventional visual methods. As a result, it was possible to record the image of tree propagation immediately after its first appearance, and to describe the specific characteristics of tree growth in terms of the length, the degraded area and the sequential images.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.540-541
• /
• 2005

• Journal of the Korean Institute of Rural Architecture
• /
• v.21 no.4
• /
• pp.37-44
• /
• 2019

A reduction in the number of high school students in Eup and Myeon districts is very severe. This issue leads to the problem with educational programs of school and an academic achievement gap. Therefore, the purpose of this study is to analyze the characteristics of areas and layout types of the floor plan of high school facilities in Eup and Myeon districts of Jeju Island where the number of students reduces and to provide a fundamental material for establishing school environments. The floor plan of school facilities was categorized into learning, support, common, and other areas and the characteristics of each area were analyzed. As a result, it was necessary to make spatial and facility improvements in common area and support area. The layout type of each area was classified into centralized type, distributed type, and mixed type, and then each type was analyzed. As a result, the main building had low points of the floor plan for learning area and common area. In order to respond to the number of students, it is required to establish reasonable spatial plan criteria and guidelines under the supervision of Office of Education and furthermore to make an effort to create futuristic educational facilities.