• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.8
• /
• pp.42-51
• /
• 1998

An 8th-order elliptic low-pass filter with cutoff frequency of 3.13kHz is presented. The design procedure is based on teh 1/s impedance transformation which is applied to a minimum capacitor LC ladder network.The tranformed network is implemented with resistors and high Q frequency-dependent negative resistors (FDNR's). The high Q FDNR is realized with two transadmittance amplifiers. Detailed SPICE simulations show that the iflter has pass-band ripple of 0.18dB, stop-band attenuation over 100dB, cutoff frequency of 3.13 khz, and cutoff frequency temperature coefficient of 8.5ppm/.deg. C at supply voltage of .+-.5V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.527-533
• /
• 1998

An optimized PWM switching strategy for an induction motor voltage control is developed and demonstrated. Space vector modulation in voltage source inverter offers improved DC-bus utilization and reduced commutation losses, and has been therefor recognizedas the perfered PWM method, especially in the case of digital implementation. Three-phase invertor voltage control by space vector modulation consists of switching between the two active and one zero voltage vector by using the proposed optimal PWM algorithm. The prefered switching sequence is defined as a function of the modulation index and period of a carrier wave. The sequence is selected by suing the inverter switching losses and the current ripple as the criteria. For low and medium power application, the experimental results indicate that good dynamic response and reduced harmonic distortion can be achieved by increasing switching frequency.

• Journal of IKEEE
• /
• v.18 no.3
• /
• pp.320-327
• /
• 2014

Recently, Importance of power management circuit technology is increased with the development of portable electric devices. This paper presents a high performance DC-DC buck converter for mobile applications. Especially, presented design have low ripple voltages and driving capability of large load current. A designed voltage mode 2-phase DC-DC converter is implemented in a $0.35{\mu}m$ CMOS process, and the overall size is $2.35{\times}2.35mm^2$. The peak efficiency is 91% with a 4MHz frequency and the maximum load current is 4A.

• Proceedings of the KIEE Conference
• /
• 2002.04a
• /
• pp.90-92
• /
• 2002

This paper presents an improved C-Dump converter system for switched reluctance motors(SRM). The proposed C-Dump converter derived from the conventional converter for SRM. The proposed converter could overcome the limitation of the conventional C-Dump converter, and could reduce the whole cost of the SRM system since the voltage stress of the dump switch $T_d$ is reduced to $V_{dc}$ when compared with $2V_{dc}$ for the conventional C-Dump converter. The attractive features of the proposed converters are; high-efficient and low-cost, elimination of dump inductor, simple control strategy, smaller size arid light weight. The proposed converter is able to be fast magnetization by $2V_{dc}$, which is sum of the input voltage and charging voltage of the dump capacitor. Also, this topology has many advantages such as freewheeling of phase winding without complex control, reduction of current ripple, reduction of torque ripple, and reduction of switching frequency. Simulation demonstrates the good performance of the converter.

• Journal of IKEEE
• /
• v.15 no.4
• /
• pp.319-323
• /
• 2011

In this paper presents a new model of dual-mode synchronous buck converter with dynamic control for mobile applications was proposed. The proposed circuit can operate at 2.5MHz with supply voltage 2.5V to 5V for low ripple and minimum inductor and capacitor size, which is suitable for single-cell lithium-ion battery supply mobile applications. For high efficiency, the proposed circuit adopts synchronous type and dynamic control. The proposed circuit is designed by using the device parameter of TSMC 0.18um BCD process and the performance is evaluated by Cadence spectre. Experimental board level results show the maximum conversion efficiency is 96% at 100mA load current.

• Journal of radiological science and technology
• /
• v.24 no.2
• /
• pp.5-11
• /
• 2001

Most of X-ray generator had used rectifier type transformer with high tension generator which is supplied in a clinical diagnosis. Because the ripple rate of tube voltage is high, X-ray generating efficiency is very low. In these days, high tension generator for inverter type X-ray generator is being supplied from a broad which uses semi-conductor switching element for the electric power that have a high speed switching ability to solve these problem. But, semi-conductor element with large capacity is used with X-ray tube's large consumption power and diffusion is difficult in the small size hospital because production cost is going up by doing digital control through DSP. Therefore, this paper designed and manufactured CR type voltage divider for feedback control of tube voltage with high frequency resonance type inverter and for high tension transformer with high frequency. It was to make economical diffusion type X-ray generator which has wide output voltage and load extent. It was preyed that the X-ray generator had the stability of X-ray tube's output characteristics.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.642-647
• /
• 1998

A new small-signal model for the controlled on-time boost power factor correction (PFC) circuit is presented. The proposed small-signal model is valid up to high frequencies over lKHz. The model can be used in designing the voltage feedback compensation of PFC circuits, the control bandwidth of which is maximized with auxiliary means of removing the low-frequency ripple from the output. The accuracy of the model is confirmed by a 200W experimental hardware

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.355-356
• /
• 2020

본 논문에서는 PFC와 LLC공진형 컨버터로 구성되는 단상 AC/DC 정류기 시스템에서 발생하는 출력전압 120Hz 리플 저감에 관한 전향보상 제어기법을 제안한다. 제안하는 방법은 입/출력 전력 차이를 이용하여 DC-link의 전압 리플을 계산하고, 선형화된 LLC공진형 컨버터의 주파수 이득 곡선을 기반으로 120Hz에 대한 리플 성분을 전향 보상하여 저감 시키는 방법이며, 시뮬레이션을 이용하여 타당성을 검증하였다.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2057-2059
• /
• 1998

In order to maintain a high quality output voltage, conventional UPS systems use complex filters with large passive components. To overcome this drawback, real time feedback control schemes have been invested. However, these techniques require a high inverter switching frequency to dynamically adapt to changing load conditions reduce harmonics of the output voltage, thereby rendering the system inadequate for high power applications. This paper presents real time digital signal processor(DSP) control of a large capacity UPS system feeding nonlinear loads to provide a sinusoidal inverter output voltage, unity input power factor, low bus voltage ripple, and excellent transient response.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.11
• /
• pp.1978-1981
• /
• 2007

Axial magnetic field was applied into the hollow anode of plasma torch for the purpose of extension of electrode lifetime. The average arc voltage increased because the arc column became longer, the arc voltage ripple frequency became low. The steady state of arc voltage was removed by applied magnetic filed. The lifetime of electrode was 60 times longer than operation without magnetic field.