• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.155-158
• /
• 2001

In this paper, the Load Current Observer Design for 3-phase Voltage Type PWM Converter with DC Meter Load. The sinusoidal input current and unity input power factor are realised based on the estimated source voltage performed by the Load Current Observer using actual currents and DC link voltage.

• Journal of the Korean Society of Safety
• /
• v.8 no.2
• /
• pp.23-29
• /
• 1993

In this study, the method of deciding simulation test conditions is developed by computer program compared to actual vehicle test as accurately as possible. These results of analytical test conditions are conformed by simulation test using the brake dynamometer by comparison with test results of actual vehicle. Results of simulation test by these analytical results show good agreement with the vehicle test results. The analytical simulation test conditions provide the input data to brake dynamometer which follows : - each test inertia corresponding to braking deceleration - test condition of input control : brake line pressure - test condition of output control : braking torque

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.6
• /
• pp.1065-1070
• /
• 2017

Magnetic gears are magnetically coupled to the input side and the output side of the rotary machine to transmit power without mechanical contact. The magnetic gear consists of an inner rotor, an outer rotor and pole pieces. Torque ripple occurs due to the difference in reluctance between the two rotors and the pole pieces during power transmission. Torque ripple is a cause of the noise and vibration of the rotary machine, so it is necessary to minimize it. In this paper, we propose a shape that cuts the corner of the pole piece and apply a fillet to reduce torque ripple. We used a two-dimensional finite element analysis method to compare and analyze the torque ripple of the magnetic gears according to the change of the fillet parameters and to find the pole piece shape with excellent torque ripple.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.6
• /
• pp.506-513
• /
• 2001

The torque of an SRM depends on the phase current and derivative of inductance. But an SRM is difficult to control the desired torques because of saturation in magnetic circuit An SRM is controlled by parameters of input voltage, and switch on , off angle The switch on off angles of an SRM regulate the magnitude and shape of current waveform and decide the magnitude and shape of torque This paper proposes an the optimization control scheme by adjusting both the switch on an switch off angle . The switch off angles are decided by reference of efficiency using simulation and experiments. The switch on angles are decided by load torque , And the dwell angles are controlled for torque control and speed control using GA-neural network which is used to simulated the reasonable switching angle.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.3
• /
• pp.320-326
• /
• 2015

Despite the wide industrial applications of planetary gear trains, the relationship between the design parameters (tooth profile, carrier mass, etc.) and performance (strength, vibration, noise, etc.) remains poorly understood. A significant amount of research has focused on transmission errors, which are measurable performance indicators directly related to the design parameters. Herein, an experimental test rig for a single-stage planetary gear set built using digital angular encoders and gap sensors is described. To study the static and dynamic characteristics of this planetary gear train, the transmission errors and sun gear orbit are analyzed from the data measured under various levels of torque and speed. The transmission errors of the gear train decrease 40% when the speed increases from 30 to 600 rpm with an output torque of 39.2 Nm, and increase 22% when the output torque increases from 19.6 to 39.2 Nm with an input speed of 30 rpm.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.3
• /
• pp.150-157
• /
• 2002

This paper presents preliminarily an implementation of digital high-performance motion control system of Reluctance Synchronous Motor (RSM) drives with direct torque control (DTC). The system consist of stator flux observer, torque estimator, two hysteresis band controllers, an optimal switching look-up table, IGBT voltage source inverter, and TMS320F240 DSP controller made by Texas Instruments. The stator fluff observer is based on the combined voltage and current model with stator flux feedback adaptive control, and the input of the observer are the stator voltage and current of motor terminal for wide speed range. The rotor position and speed sensor used 6000 pulse/rev encoder. In order to prove rightness of the suggested control algorithm, we have some simulation and actual experimental system at $\pm$20 and $\pm$2000 rpm. The developed digitally high-performance motion control system+ are shown a good response characteristic of control results and high performance features using 1.0kW RSM which has 2.57 Ld/Lq salient ratio.

• Proceedings of the KIEE Conference
• /
• 2002.04a
• /
• pp.55-57
• /
• 2002

In industry, A pallet truck is drived mainly by d.c motor, because it use to battery for input power. However, d.c motor has a brush, this is the disadvantage of the d.c motor for a pallet truck. Though a brushless d.c motor has a permanent magnet, it is for low torque. Switched reluctance motors(SRM) have the advantage a high torque/weight ratio, as the large reluctance torque is made by salient poles of both start and rotor, and a high reliability, this paper design the shape of the switched reluctance motor that will replace a d.c motor for A pallet truck. First of all, designed parameter of SRM, outer diameter, diameter of rotor and stock length, from the outputr equation considering electric loading and magnetic loading. Next, design diameter of stator and rotor, depth of slot pole width, air gap as inner size of motor. The design of SRM certify the torque, the efficiency and the output power by a simulation.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.6 no.2
• /
• pp.1-6
• /
• 2009

The APU(Auxiliary Power Unit) needs a set of complex pipeline for the fuel supply system where some of the main valves controlling the flow rate consist of the servo valve worked with a torque motor. The input electric current produces an induced magnetic field almost perpendicular to the background magnetic filed generated by fixed permanent magnets. The induced torque deforms the tubular bushing, and directly rotates an armature, which can open and close the valve. In this study, we start from a basic analytic model using a simple electro-magneto-statics, and expand our model to the three-dimensional one computationally applying a commercial code named COMSOL. The result is compared with each other, and reasonable numerical data are obtained for the dynamic behavior and multi-physics system.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.3
• /
• pp.329-338
• /
• 2007

Purpose. The aim of this study is to evaluate the effect of TiN coating of abutment screw on the unscrewing torque. Material and methods. Titanium and Gold-Tite abutment screws were classified into two groups, Group A and C respectively, as control groups. Titanium abutment screws with TiN coatings were also classified into two groups, Group B and D, as experimental ones. Group A and B were tightened to 20 Ncm input torque, and Group C and D were tightened to 32 Ncm torque. Detorque values were measured with digital torque gauge during repeated closing and opening experiment. Results. Abutment screws with TiN coating (Group B and D) showed statistically significant higher mean detorque values than those of Group A and C. Discussion. Physical properties of TiN coating, such as low friction coefficient, high hardness and wear resistance, might contribute to higher detorque values. Conclusion. It is suggested that TiN coating of abutment screw help to reduce the risk of screw loosening and improve the stability of screw joint.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.109-112
• /
• 2006

In the recent studies, various types of multi mode electric variable transmission for hybrid electric vehicle have been proposed. Multi mode electric variable transmission consists of two or more different type planetary gear hybrid powertrain system(PGHP), which can change its power flow type by means of clutches for improving transmission efficiencies. Generally the power flows can be classified into three different types such as Input split, output split nd compound split. In This paper, we present velocity and torque equations of the input-split powertrain and analyze its optimal Performances. There are six combinations of the input-split powertrain, each combination has various lever length. We find optimal planetary gear ratios for fuel economy and acceleration performance, and compare performances of each combination.