• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.505-507
• /
• 2004

This paper attempts to compensate the nonlinearity between the input voltage and the output displacement of the piezoelectric stack in dynamic actuation by the following two ways. Firstly, the charge steering by circuit configuration reduces the hysteresis of piezoelectric actuator remarkably. However, it makes the ripple in positioning due to the phase lag and noise induced from the elements of the long closed loop. Secondly, the feedforward control by neural network compensates the hysteresis of the piezoelectric actuators effectively with the appropriate selection of the input variables for the training. The improvement of the dynamic performance of the piezoelectric actuators by the developed linearization technique is verified by experiments.

• Proceedings of the KIPE Conference
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.323-326
• /
• 1999

For decrease the harmonic current components of the power source, a first method is insert the choke coil that used the choke input type rectifier, the booster chopper circuit and buck chopper circuit. And the several method are studying like as the PWM(Pulse Width Modulation) converter and the active filter type which is used the high frequency switching and the sinusoidal wave formed input current. In this type, there are many problem as a low efficiency, increased the noise, the high leakage current and cost up by the high frequency switching. For improve this problems, the partial resonan method is used on the booster inducter and lossles snubber condenser. This method decreased the distortion factor has lower harmonic components than the hard switching and there is no switching loss by the ZCS(Zero Current Switching) at switch turn-on and the ZVS(Zero Voltage Swithcing) at switch turn-off

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.581-584
• /
• 2003

The phase differences and noise signals are in general serious on output of a instrumentation amplifier for signal conditioning of a sensor driven at high frequency due to a time-varying input signal. In this study, we get the better amplification and S/N ratio using the rectified signal for the input of instrumentation amplifier. This driving circuits were designed and constructed by OrCAD and laboratory PCB process. All of the elements used on the circuit including highly speedy OP-Amp. was SMD type and the MI sensor was fabricated by meander-patterned amorphous ribbon. The output sensitivity of this circuit was $105.3mV/V{\cdot}Oe$. That's why this driving circuit is good at detection of fine magnetic field.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2002년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.290-293
• /
• 2002

For small capacity rectifier circuits such as these for consumer electronics and appliances, capacitor input type rectifier circuits are generally used. Consequently, various harmonics generated within the power system become a serious problem. Various studies of this effect have been presented previously. However, most of these employ switching devices, such as FETs and the like. The absence of switching devices makes systems more tolerant to over-load, and brings low radio noise benefits. We propose a power factor connection scheme using a LC resonant in commercial frequency without switching devices. In this method, It makes a sinusoidal wave by widening conduction period using the current resonance in commercial frequency, Hence, the harmonic characteristics can be significantly improved, where the lower order harmonics, such as the fifth and seventh orders are much reduced. The result are confirmed by the theoretical and experimental implementations.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 한국방송공학회 1995년도 학술대회
• /
• pp.165-170
• /
• 1995

In this paper, it is attempted to apply the adaptive digital signal processing to compensate for a linear distortion of a loudspeaker and implement a real time hardware for that purpose. The real time system is implemented by using the DSP56001, a general purpose signal processor, as a host processor and the DSP56200, a cascadable adaptive FIR filter peripheral chip, as an adaptive digital filter. The system has 1000 taps at a 44.1kHz. After inverse modeling of under_compensation_speaker, the system reduces loudspeaker's linear distortions by pre-processing an input audio signal to loudspeaker. The experiment shows satisfactory results; after adaption with white noise as input signal for 60sec, the flat amplitude and linear phase frequency characteristics is found to lie over a wide frequency range of 100Hz to 20kHz.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 한국조명전기설비학회 2003년도 학술대회논문집
• /
• pp.403-406
• /
• 2003

For small capacity rectifier circuits such as these for consumer electronics and appliances, capacitor input type rectifier circuits are generally used. Consequently, various harmonics generated within the power system become a serious problem. Various studies of this effect have been presented previously. However, most of these employ switching devices, such as FET and the like. The absence of switching devices mattes systems more tolerant to over-load and brings low radio noise benefits. We propose a power factor correction scheme using a LC resonant in commercial frequency without switching devices. In this method It makes a sinusoidal wave by widening conduction period using the current resonance in commercial frequency, Hence, the harmonic characteristics can be significantly improved, where the lower order harmonics, such as the fifth and seventh orders are much reduced The result are confirmed by the theoretical and experimental implementations.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• 제22권1호
• /
• pp.46-52
• /
• 2012

Since the engine and reduction gear in a naval vessel are usually supported by the mounting system separately, the misalignment between the input shaft of the reduction gear and the output shaft of the engine should occur caused by ship motion. In this study, this misalignment is estimated from the linear static analysis assuming that the phase of movements of the engine and reduction gear at low frequency range is same and the dynamic effect is not affect to them. Through comparing the relative displacement of the engine and reduction gear calculated from linear static analysis to that from dynamic analysis as well as experiment, the assumption in this study could be verified.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• 제32A권9호
• /
• pp.1257-1263
• /
• 1995

This paper presents a method not only to detect moving targets from ISAR data corrupted by heavy clutter but to effectively extract the moving targets' signitures that are necessary for acquiring the velocities and images of the targets. In this method, input ISAR data are coherently processed such that echoes due to the moving targets are transformed to be in-phase and then integrated. It is shown that targets' signitures are localized in the transformed two-dimensional domain, leading to dramatic improvement of signal-to-noise (SNR) ration. The extent of the improved signal-to-noise ratio is analyzed and results implemented with simulated ISAR data are presented.

• Proceedings of the KSR Conference
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.1887-1891
• /
• 2008

In this paper, we dealt with a partial discharge (PD) measurement method that has been accepted as an effective and non-destructive technique to estimate insulation performance of low-voltage induction motors. The PD measurement system consists of a coupling network, a low noise amplifier, and associated electronics. A shielded box was used to reduce environmental noise. Frequency characteristic of the coupling network was estimated by a sinusoidal signal input, and the low cut-off frequency of the coupling network was 1 MHz (-3 dB). Also, we carried out a calibration test for the PD measurement system. Sensitivity of the system was of 84 m$V_{max}$/pC between stator winding and enclosure. In application test on a low-voltage three phase induction motor (5 HP), we could detect 88 pC at AC 800 $V_{max}$.

• Speech Sciences
• /
• 제8권4호
• /
• pp.59-72
• /
• 2001

In this paper, we experimented with speaker change detection that uses a statistical method for NOD (News On Demand) service. A specified speaker's change can find out content of each data in speech if analysed because it means change of data contents in news data. Speaker change detection acts as preprocessor that divide input speech by speaker. This is an important preprocessor phase for speaker tracking. We detected speaker change using GLR(generalized likelihood ratio) distance base division and BIC (Bayesian information criterion) base division among matrix method. An experiment verified speaker change point using BIC base division after divide by speaker unit using GLR distance base method first. In the experimental result, FAR (False Alarm Rate) was 63.29 in high noise environment and FAR was 54.28 in low noise environment in MDR (Missed Detection Rate) 15% neighborhood.