• 드라이브 ㆍ 컨트롤
• /
• 제14권3호
• /
• pp.40-49
• /
• 2017

This study presents an online estimation of an excavator's rotational inertia by using recursive least square with forgetting. It is difficult to measure rotational inertia in real systems. Against this background, online estimation of rotational inertia is essential for improving safety and automation of construction equipment such as excavators because changes in inertial parameter impact dynamic characteristics. Regarding an excavator, rotational inertia for swing motion may change significantly according to working posture and digging conditions. Hence, rotational inertia estimation by predicting swing motion is critical for enhancing working safety and automation. Swing velocity and damping coefficient were used for rotational inertia estimation in this study. Updating rules are proposed for enhancing convergence performance by using the damping coefficient and forgetting factors. The proposed estimation algorithm uses three forgetting factors to estimate time-varying rotational inertia, damping coefficient, and torque with different variation rates. Rotational inertia in a typical working scenario was considered for reasonable performance evaluation. Three simulations were conducted by considering several digging conditions. Presented estimation results reveal the proposed estimation scheme is effective for estimating varying rotational inertia of the excavator.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 F
• /
• pp.2078-2081
• /
• 1997

IP speed controller is used as a main controller and it makes the system low overshoot and easy controllability. Load torque is estimated by Kalman filter algorithm and parameter controller is used against a rotor inertia negative variations. Parameter Controller (PC) is equipped with a torque observer implemented by software of a digital signal Processor. PC is a parameter controller which selects a moment of inertia J in responding to a load torque to control the system response.

• International Journal of Automotive Technology
• /
• 제8권2호
• /
• pp.233-241
• /
• 2007

A lumped parameter model is proposed for the analysis of dynamic behaviour of a Passive Hydraulic Engine Mount (PHEM), incorporating inertia track and throttle, which is characterized by effective and efficient vibration isolation behaviour in the range of both low and high frequencies. Most of the model parameters, including volume compliance of the throttle chamber, effective piston area, fluid inertia and resistance of inertia track and throttle are identified by an experimental approach. Numerical predictions are obtained through a finite element method for responses of dynamic stiffness of the rubber spring. The experiments are made for the purpose of PHEM validation. Comparison of numerical results with experimental observations has shown that the present PHEM achieves good performance for vibration isolation.

• 로봇학회논문지
• /
• 제17권3호
• /
• pp.347-352
• /
• 2022

The paper presents how to update impedance control parameters for dual-arm manipulators using EMG signals and motions of the operator. Since the hand motions of the dual-arm are modeled to be the mass-spring-damper system in this paper, the impedance parameter update method is an important issue to reflect the operator's force. However, task space inertia to be used as the mass parameter goes to infinity if the manipulator approaches a kinematic singularity. To alleviate this issue, the impedance (stiffness and damping) parameters are divided with a diagonal element of the task space inertia. Also, the stiffness and damping matrices are updated using the normalized EMG signals captured from the operator's forearm. Through this process, the motion of the dual-arm manipulator is more stabilized even though it approaches the kinematic singularity.

• 융합신호처리학회논문지
• /
• 제2권3호
• /
• pp.65-72
• /
• 2001

일반적으로 관성시스템의 제어 문제는 결국, 시스템 자체에서 발생하는 진동을 최대한 억제하면서 빠른 시간에 출력이 기준입력을 추종하는데 있다. 이 경우 문제로 되는 것은 시스템의 모델링 과정에서 발생하는 플랜트의 불확실성과 parameter 변동이다. 여기서는 일반적인 강인한 제어기 설계 이론의 하나인 H$_{*}$ 이론이 가지는 단점인 제어기의 보수성을 극복하면서, 동시에 출력의 과도응답특성을 개선하기 위한 방법으로 H$_2$이론을 병용하고 이를 LMI 이론으로 해석하였다. 이 과정에서 3 관성시스템에 LMI 이론을 적용하기 위한 일반화플랜트의 모형을 제시하고 이것의 유효성을, 모델의 불화실성과 parameter변동을 동시에 고려한 simulation을 통하여 확인하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.801-804
• /
• 2006

The purpose of this paper is to investigate the stability of stepped cantilever columns with a tip mass of rotatory inertia and a translational spring at one end. The column model is based on the Bernoulli-Euler theory which neglects the effects of rotatory inertia and shear deformation. The governing differential equation for the free vibration of columns with stepwise variable cross-section and subjected to a subtangential follower force is solved numerically using the corresponding boundary conditions. And the bisection method is used to calculate the critical divergence/flutter load. The frequency and critical divergence/flutter load for the stepped column with a single step are presented as functions of various non-dimensional system parameters: the segmental length parameter, the section ratio, the subtangential parameter, the mass, the moment of inertia of the mass, and the spring parameter.

• 한국소음진동공학회논문집
• /
• 제11권9호
• /
• pp.462-474
• /
• 2001

In this paper, Generalized Differential Quadrature Method is applied to the buckling analysis of built-up columns without or with stay plates. numerical analysis using GDQM is carried out for various boundary conditions(simply supported conditions, fixed conditions, fixed-simply supported conditions), dimensionless stiffness parameter and dimensionless inertia moment parameter. The accuracy and convergence of solutions are compared with exact solutions of Gjelsvik to validate the results of GDQM. Results obtained by this method are as follows. 91) This method can yield the accurate numerical solutions using few grid points. (2) The buckling load of built-up column increases as the dimensionless stiffness parameter decreases. (3) The effects of boundary conditions on the buckling load are not considerable as the dimensionless stiffness parameter increases. (4) The buckling load of built-up column increases due to the stay plate.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 A
• /
• pp.219-223
• /
• 1995

This paper deals with the robust control system for parameter variations, fast responses and load torque variations. Frist, fuzzy-sliding adaptive control be used to. Fuzzy-sliding adaptive control is good at fast response. Second, there are many requests for selecting freely the moment of inertia, even though moment of inertia is determined with the materials, structure, shape, and size of the motors. Therefore we developed an inertia-lowering control system that uses torque observer to reduce the moment of inertia. Finally, using torque observer, torque control is done so as to compensate load torque. Consequently, the proposed system verified the superiority through the simulations using MATLAB.

• 융합신호처리학회 학술대회논문집
• /
• 한국신호처리시스템학회 2001년도 하계 학술대회 논문집(KISPS SUMMER CONFERENCE 2001
• /
• pp.129-132
• /
• 2001

본 논문은 3 관성시스템의 진동억제를 위한 강인한(robust) 제어기의 설계법을 제안하고 이를 simulation 을 통하여 확인하는데 있다. 일반적으로 관성 시스템의 제어 문제는 결국. 시스템 자체에서 발생하는 진동을 최대한 억제하면서 빠른 시간에 원하는 위치에 출력을 가져가는 데 있다. 이 경우 문제로 되는 것은 시스템의 모델링 과정에서 발생하는 플랜트의 불확실성과 parameter 변동이다. 여기서는 일반적인 강인한 제어기 설계 이론의 하나인 $H_{\infty}$ 이론이 가지는 단점인 제어기의 보수성을 극복하면서, 동시에 출력의 과도응답특성을 개선하기 위한 방법으로 $H_2$ 이론을 병용하고 이를 LMI 이론으로 해석하였다. 이 과정에서 3 관성시스템에 LMI 이론을 적용하기 위한 일반화플랜트의 모형을 제시하고 이것의 유효성을, 모델의 불확실성과 parameter변동을 동시에 고려한 simulation을 통하여 확인하였다.

• 전기학회논문지
• /
• 제56권2호
• /
• pp.311-316
• /
• 2007

This paper proposes the algorithm which estimates moment of the inertia and friction coefficient of friction for high performance speed control of electric motor. The proposed algorithm finds the moment of inertia and friction coefficient of friction by observing the speed error signal generated by the speed observer and using Recursive Least-Mean-Square method(RLS). By feedbacking the estimated inertia and estimated coefficient of friction to speed controller and full order speed observer, then the errors of the inertia and coefficient of friction and speed due to the inaccurate initial value are decreased. Inertia and coefficient of friction converge to the actual value within several times of speed changing. Simulation and actual experiment results are given to demonstrate the effectiveness of the proposed parameter estimator.