• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.9
• /
• pp.19-27
• /
• 1998

The Transmitter part of single RF transceiver chip for an extended GSM handset application was circuit-designed, fabricated adn evaluated. The RF-IC Chip was processed by 0.8${\mu}m$ Si BiCMOS, 80 pin TQFP of $10 {\times} 10mm$ size, 3.3V operated RF-IC reveals, in general, quite reasonable integrity and RF performances. This paper describes development resuts of RF transmitter section, which includes IF/RF up-conversion mixer, IF/RF polyphase and pre-amplifier. The test results show that RF transmitter section is well operated within frequency range of 880~915MHz, which is defined on the extended GSM(E-GSM) specification. The transmitter section also reveals moderate power consumption of 71mA and total output power of 8.2dBm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.8C
• /
• pp.637-644
• /
• 2012

In this paper, a new compact power divider is suggested. Instead of the quarter wavelength transmission line(TX-line)s for the branches of the conventional Wilkinson's power divider design method, we use our composite right- and left-handed(CRLH) TX-line zeroth order resonator(ZOR) bandpass filters of one twelfth wavelength and reduce the physical length of the power divider. Besides, the filters in the branches can secure the passband for power-division. To validate the proposed power divider, we take an L-band for millitary satellaite transponder as the test case and the performances of the circuit and full-wave simulation results with the CRLH properties of the structure are shown with the dispersion curve and E-field at the ZOR. The measurement is compared with the simulation results. Also, the size reduction effect by the proposed scheme is addressed

• Journal of IKEEE
• /
• v.14 no.3
• /
• pp.190-198
• /
• 2010

This paper describes a auto focus piezo actuator driver IC for portable digital camera. The 80[V] DC voltage is generated by a DC-DC converter and supplied to power of piezo moving control circuit. The voltage of piezo actuator needs range -20[V] to 80[V] proportional to 1[Vp-p] input control voltages. The dimensions and number of external parts are minimized in order to get a smaller hardware size. IIC(Inter-IC) interface logic is designed for data interface and it makes debugging easy, test for mass productions. The power consumption is around 40[mW] with supply voltage of 3.6[V]. This device has been fabricated in a 0.6[um] double poly, triple metal 100[V] BCD MOS process and whole chip size is 1600*1500 [$um^2$].

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.3
• /
• pp.55-61
• /
• 2000

This paper presents an efficient hardware architecture of frame memory interface in MPEG-2 video encoder. To reduce the size of memory buffers between SDRAM and the frame memory module, the number of clocks needed for each memory access is minimized with dual bank operation and burst length change. By allocating the remaining cycles not used by SDRAM access, to the random access cycle, the internal buffer size, the data bus width, and the size of the control logic can be minimized. The proposed architecture is operated with 54MHz clock and designed with the VT $I^{тм}$ 0.5 ${\mu}{\textrm}{m}$ CMOS TLM standard cell library. It is verified by comparing the test vectors generated by the c-code model with the simulation results of the synthesized circuit. The buffer area of the proposed architecture is reduced to 40 % of the existing architecture.

• Journal of IKEEE
• /
• v.17 no.3
• /
• pp.260-266
• /
• 2013

The open bit line is vulnerable to noise compared to the folded bit line when read/write for the DRAM. According to the increasing DRAM densities, the core circuit operating conditions is exacerbated by the noise when it comes to the open bit line 6F2(F : Feature Size) structure. In this paper, the interference effects were analyzed by the data patterns between the bit line by experiments. It was beyond the scope of existing research. 68nm Tech. 1Gb DDR2, Advan Tester used in the experiments. The noise effects appears the degrade of internal operation margin of DRAM. This paper investigates sense amplifier power line splits by experiments. The noise can be improved by 0.2ns(1.3%)~1.9ns(12.7%), when the sense amplifier power lines split. It was simulated by 68nm Technology 1Gb DDR2 modeling.

• Korean Journal of Optics and Photonics
• /
• v.20 no.2
• /
• pp.71-75
• /
• 2009

A compact electric field probe sensor incorporating two different electro-optic materials of $LiNbO_3$ and GaAs was proposed and fabricated, and it was used to measure the strength of the horizontal and vertical fields generated by a microstrip ring-resonator filter. The sensitivities of the sensors in $LiNbO_3$ and GaAs were $9.315{\mu}V/\sqrt{Hz}$ and ${\sim}49.346{\mu}V/\sqrt{Hz}$ respectively, and their signal to noise ratios were approximately ${\sim}50\;dB$ and ${\sim}40\;dB$ respectively. And the operating frequency range was up to ${\sim}1.2\;GHz$. The electric field profile for the test circuit was scanned and found to be in good agreement with that obtained by using the HFSS simulation.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.935-943
• /
• 2015

Permanent magnetic actuators (P.M.A.s) are widely used to drive medium-voltage-class vacuum circuit breakers (V.C.B.s). In this paper, a method for design optimization of a P.M.A. for V.C.B.s is discussed. An optimal design process employing the response surface method (R.S.M.) is proposed. In order to calculate electromagnetic and mechanical dynamic characteristics, an initial P.M.A. model is subjected to numerical analysis using finite element analysis (F.E.A.), which is validated by comparing the calculated dynamic characteristics of the initial P.M.A. model with no-load test results. Using tables of mixed orthogonal arrays and the R.S.M., the initial P.M.A. model is optimized to minimize the weight of the permanent magnet (P.M.) and to improve the dynamic characteristics. Finally, the dynamic characteristics of the optimally designed P.M.A. are compared to those of the initially designed P.M.A.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.10
• /
• pp.820-826
• /
• 2013

In this paper, a compact and wideband CLAS(Conformal Load bearing Antenna Structure) was studied using smart skin technique. In order to satisfy the electrical performance of the CLAS antenna, the proposed CLAS antenna is composed of conductive mesh, face-sheet, radiator, honeycomb, housing. Especially, radiator is composed of composite magneto-dielectric material and radiating element etched on the PCB (Printed Circuit Board). The radiating element is inserted into the composite magneto-dielectric material and has sloted Folded LP(Log Periodic) structure. By fabricated composite magneto-dielectric, the resonance frequency is decreased and the impedance matching characteristics is improved. We verified that the antenna has wideband characteristics and compact size using the antenna test results.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.4
• /
• pp.1-7
• /
• 2006

A major failure mode for wafer level chip size package (WLCSP) is thermo-mechanical fatigue of solder joints. The mechanical strains and stresses generated by the coefficient of thermal expansion (CTE) mismatch between the die and printed circuit board (PCB) are usually the driving force for fatigue crack initiation and propagation to failure. In a WLCSP process peripheral or central bond pads from the die are redistributed into an area away using an insulating polymer layer and a redistribution metal layer, and the insulating polymer layer affects solder joints reliability by absorption of stresses generated by CTE mismatch. In this study, several insulating polymer materials were applied to WLCSP to investigate the effect of insulating material. It was found that the effect of property of insulating material on WLCSP reliability was altered with a solder ball layout of package.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.2
• /
• pp.101-109
• /
• 2005

The purpose of this study is to investigate the performance of outdoor heat exchanger for heat pump using carbon dioxide. Two types of fin and tube heat exchangers (2 rows for type A and 3 rows for B) are tested. Both heat exchangers have counter-cross flow and 1-circuit arrangement. Test results such as heat transfer rate, pressure drop characteristics and temperature distribution in the heat exchanger are shown with respect to mass flow rate of refrigerant and frontal air velocity For cooling mode, the minimum temperature difference between air and refrigerant of type B is smaller than that of type A by $1^{circ}C$, but the pressure loss of air side is much higher for type B by $29\%$. It is found that a large temperature gradient of carbon dioxide during gas cooling Process Promotes thermal conduction through tube wall and fins which results in degradation of heat transfer performance. For heating mode operation, type B heat exchanger shows higher heat transfer performance compared to type A. However, because pressure loss of refrigerant side of type B is much greater than that of type A, the refrigerant outlet pressure of type B becomes lower than that of type A.