• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.6
• /
• pp.664-671
• /
• 2010

In this paper, we developed a Zigbee module based on CC2520 which is possible to construct the mesh network and also support to Zigbee Pro standard as a preceding research of autonomous moving of mobile robot using Zigbee. After manufacturing the Zigbee module, we selected antenna to fit Zigbee wireless frequency band using network analyze as means performance improvement. We also carry out an impedance matching of Zigbee module, extend the possible distance of two-way wireless communication and ensure the safety of communication.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.99.5-99
• /
• 2001

This study presents a simulation of the traction return current based on $2{\times}25kV$ power supply system in order to determine the impedance bond intensity of impulse type track circuit on the electrified Gyeongbu line. The results of the simulation enables us to measure the precise intensity of catenary current that returns to the substation through KTX (Korean Train Express) operated by $2{\times}25kV$ power supply system with common earth network. The combination of $2{\times}25kV$ and common earth network established on the electrified Gyeongbu line for the first time in Korea. We show that the relationships among the traction return current, earth current, and catenary current, and catenary current can be applied to this line in order to determine the optimal impedance bond intensity ...

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2228-2230
• /
• 2002

The research presented in this paper focuses on a method for the detection of High Impedance Fault(HIF). The method will use the Lifting and neural network system. HIF on the multi-grounded three-phase four-wires primary distribution power system cannot be detected effectively by existing over current sensing devices. These paper describes the application of lifting scheme to the various HIF data. These data were measured in actual 22.9kV distribution system. Wavelet transform analysis gives the frequency and time-scale information. The neural network system as a fault detector was trained to discriminate HIF from the normal status by a gradient descent method. The proposed method performed very well by proving the right state when it was applied staged fault data and normal load mimics HIF, such as arc-welder.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.60-63
• /
• 2003

This paper describes the design and the simulation of a V-band single pole double throw (SPDT) FET switch fur millimeter-wave applications using drain impedance transformation network with CPW transmission line. The designed switch has about 10% bandwidth at 60GHz. Insertion loss is better than 3dB fur the ON state and Isolation is larger than 30dB fer the OFF state. The maximum isolation is 43.4dB at 60GHz with input power of 10dBm. The yield analysis is done considering the effects of pHEMT variations.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1402-1404
• /
• 2000

The electrified railway has various power supply schemes. Although the identical trains are operated in same condition and the impedance of track are equal, the genealogy impedance of track is changed according to composition method of feeding scheme. So, the harmonic current flowing into the railway substation are greatly unlike. For simulation of harmonic magnification flowing into the railway substation according to feeding scheme, we propose 6-port network analysis method based on 4-port network, find 6-port equivalent model of each circuit component, and compare and investigate harmonic magnification in the case of parallel post and normal feeding scheme.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.137-138
• /
• 2006

In this paper, we study the algorithm for the multiport measurements using the 2port VNA(Vector network Analyzer). We explain the conversion algorithm which the open impedance to the matched impedance(50 ohm), and then we apply this algorithm to the 4 port VNA measurement. Finally, we discuss the reliability of this algorithm.

• Proceedings of the KIPE Conference
• /
• 2016.11a
• /
• pp.220-221
• /
• 2016

This paper proposes an active switched-capacitor embedded quasi-Z-source inverter (ASC-EqZSI) topology. In order to improve boost ability, One diode and one switch device are added in the qZSI impedance network, and a single dc source is shifted in series with the inductor in the impedance network. The performances of the proposed topology are verified with simulation and experimental results.

• International Journal of Computer Science & Network Security
• /
• v.23 no.1
• /
• pp.120-124
• /
• 2023

Strong surface waves among collinearly arranged patch antenna arrays pose unwanted inter element coupling particularly when high permittivity dielectric materials are used. In order to avert those waves, a novel Defected Ground Structure (DGS) is carved out systematically between two E-plane patch antenna elements. The introduced low profile μ shaped structure consequently improves impedance bandwidth and reflection coefficient by suppressing surface waves considerably. Parametric simulation results are analyzed and discussed.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.4
• /
• pp.152-158
• /
• 1997

An analyzing method for pressure fluctuations in oil hydraulic pipe network was developed in this study. The object pipe network has multi-branch configuration, and the pipelines of it are composed of steel tubes, flexible hoses. Also, accumulators, orifices and lumped oil volume components are attached on it. Transfer matrix method, in other words impedance method, was used for the analysis. The reliability and usefulness of the analyzing method were confirmed by investigation computed results and experimental results got in this study.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.9
• /
• pp.1344-1350
• /
• 1990

A design method of ultra-broadband microwave amplifier is presented. A lossy network is represented as the combination of a serial impedance component and a parallel admittance component, and the realizable ranges of the gain and the reflection coefficients are derived with the components connected to the input, output or interstage network. The matching network has been designed by using the serial and parallel immittance loci which have the constant gain or reflection coefficients within the realizable ranges. Using the proposed method, deisgn examples of ultra-broadband amplifiers operating from dc to 12GHz frequency range are presented.