• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.5
• /
• pp.203-207
• /
• 2019

Calcium phosphates such as hydroxyapatite (HAp), tricalcium phosphate (${\beta}$-TCP), and biphasic calcium phosphate (BCP, HAp/${\beta}$-TCP) have been prepared via hydrothermal treatment. The synthesis was conducted by reacting ($Ca(OH)_2$) aqueous solution with phosphoric acid ($H_3PO_4$) under different hydrothermal synthesis conditions (temperatures up to $150^{\circ}C$ and pH lower than 12). The effects of initial precursor Ca/P ratio (1.30, 1.50 and 1.67) and post heat treatment on the phase evolution behavior of the powders and sintered ceramics were investigated. The phases of resulting powders and sintered ceramics were controllable by adjusting the initial Ca/P ratio. A single HAp phase without any noticeable second phase was obtained for the initial Ca/P ratio of 1.67 in the overall heat treatment range. Pure ${\beta}$-TCP and biphasic calcium phosphate (HAp/${\beta}$-TCP) were synthesized from precursor solutions having Ca/P molar ratios of 1.30 and 1.50, respectively, after having been heat treated at $900^{\circ}C$ or higher. Dense ceramics with translucency were obtained at considerably lower sintering temperatures.

• Journal of the Korean Ceramic Society
• /
• v.26 no.6
• /
• pp.737-746
• /
• 1989

After Ba-ferrite powders synthesized hydrothermally and its heated powders were dissolved partially with HCl treatment time, the BaO/Fe2O3 mole ratio of dissolved solutions and powders were measured by AAS, also, lattice constants, particle morphology and magnetic properties in HCl treated, heated and no-heated Ba-ferrite powders were abtained by means of XRD, SEM and VSM, respectively. From above analysis results, the effect of Ba/Fe mole ration in suspension(as starting material) on the BaO/Fe2O3 composition and particle characteristics of products were investigated, and the effect of heat treatment on magnetic properties of products examined. The composition, lattice constant and crystal phase of products depend on the Ba/Fe mole ratio in suspension. Ba content in surface or outer part of Ba-ferrite powder is higher than inner and heterogeneous, and the excess Ba ions in the inner part of particle move into the outer by heating, so that the mole ratio of BaO/Fe2O3 in the more jinner approaches more to the stoichiometric composition 1 : 6. The crystallinity, coercivity and saturation magnetization of products are increased by heat treatment, and the heat-treated samples synthesized hydrothermally in lower temperature are appreciated to have better powder characteristics.

• Journal of Powder Materials
• /
• v.18 no.1
• /
• pp.14-17
• /
• 2011

$TiO_2$ nanopowders with anatase structure were firstly prepared by controlling the pH value of a precursor solution without any heat-treatment at room temperature. The prepared $TiO_2$ nanopowders were hydrothermally treated in 10M NaOH solution at $170^{\circ}C$. Then, the samples were washed in DI water or 0.1M HCl. The $TiO_2$ nanotubes were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM). The gas sensitivity of $TiO_2$ nanotubes for toluene gas was also investigated. The results show that $TiO_2$ nanotubes can be prepared by hydrothermal treatment. The morphology of $TiO_2$ nanotubes prepared by 0.1M HCl washing is destroyed to some extent. $TiO_2$ nanotubes with DI water washing show better sensitivity than that with 0.1M HCl washing.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.21 no.1
• /
• pp.33-42
• /
• 2005

This study was performed to investigate the surface properties and in vitro biocompatibility of electrochemically oxidized Ti-6Al-7Nb alloy by anodic spark discharge technique. Discs of Ti-6Al-7Nb alloy of 20 mm in diameter and 2 mm in thickness were polished sequentially from #300 to 1000 SiC paper, ultrasonically washed with acetone and distilled water for 5 min, and dried in an oven at $50^{\circ}C$ for 24 hours. Anodizing was performed using a regulated DC power supply. The applied voltages were given at 240, 280, 320, and 360 V and current density of $30mA/cm^2$. Hydrothermal treatment was conducted by high pressure steam at $300^{\circ}C$ for 2 hours using a autoclave. Samples were soaked in the Hanks' solution with pH 7.4 at $36.5^{\circ}C$ during 30 days. The results obtained were summarized as follows; 1. The oxide films were porous with pore size of $1{\sim}5{\mu}m$. The size of micropores increased with increasing the spark forming voltage. 2. The main crystal structure of the anodic oxide film was anatase type as analyzed with thin-film X-ray diffractometery. 3. Needle-like hydroxyapatite (HA) crystals were observed on anodic oxide films after hydrothermal treatment at $300^{\circ}C$ for 2 hours. The precipitation of HA crystals was accelerated with increasing the spark forming voltage. 4. The precipitation of the fine asperity-like HA crystals were observed after being immersed in Hanks' solution at $37^{\circ}C$. The precipitation of HA crystals was accelerated with increasing the spark forming voltage and the time of immersion in Hanks' solution. 5. The Ca/P ratio of the precipitated HA layer was equivalent to that of HA crystal as increasing the spark forming voltage and the time of immersion in Hanks' solution.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.22 no.1
• /
• pp.101-110
• /
• 2006

This study was performed to investigate the surface properties and in vitro biocompatibility of electrochemically oxidized Ti-6Al-7Nb alloy by anodic spark discharge technique. Discs of Ti-6Al-7Nb alloy of 20 mm in diameter and 2 mm in thickness were polished sequentially from #300 to 1000 SiC paper, ultrasonically washed with acetone and distilled water for 5 min, and dried in an oven at $50^{\circ}C$ for 24 hours. Anodizing was performed using a regulated DC power supply. The applied voltages were given at 240, 280, 320, and 360 V and current density of $30mA/cm^2$. Hydrothermal treatment was conducted by high pressure steam at $300^{\circ}C$ for 2 hours using a autoclave. Samples were soaked in the Hanks' solution with pH 7.4 at $36.5^{\circ}C$ during 30 days. The results obtained were summarized as follows; 1. The oxide films were porous with pore size of $1{\sim}5{\mu}m$. The size of micropores increased with increasing the spark forming voltage. 2. The main crystal structure of the anodic oxide film was anatase type as analyzed with thin-film X-ray diffractometery. 3. Needle-like hydroxyapatie (HA) crystals were observed on anodic oxide films after hydrothermal treatment at $300^{\circ}C$ for 2 hours. The precipitation of HA crystals was accelerated with increasing the spark forming voltage. 4. The precipitation of the fine asperity-like HA crystals were observed after being immersed in Hanks' solution at $37^{\circ}C$. The precipitation of HA crystals was accelerated with increasing the spark forming voltage and the time of immersion in Hanks' solution. 5. The Ca/P ration of the precipitated HA layer was equivalent to that of HA crystal as increasing the spark forming voltage and the time of immersion in Hanks' solution.

• Korean Journal of Materials Research
• /
• v.17 no.8
• /
• pp.437-441
• /
• 2007

Preparation and morphology control of $TiO_2$ nano powders for gas sensor applications are investigated. $TiO_2$ nanopowders with rutile and anatase structures were prepared by controlling the pH value of a precursor solution without any heat treatment. The mean particle size of $TiO_2$ powders were below 10nm. The prepared $TiO_2$ nano powders were hydrothermal treated by NaOH solution. The sample was washed in HCl solution. As a result and $TiO_2$ nanotubes were formed. The lengths of $TiO_2$ nanotube were $1{\mu}m$ and the diameters were 10nm. Crystal structure and microstructure of $TiO_2$ nanotube were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscope (TEM). As-prepared $TiO_2$ nanotube powders have several advantages of nano particle size and high surface area and could be a prominent candidate for nano-sensors. The sensitivity of $TiO_2$ nanotube sensor was measured for toluene and NO in this study.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.4
• /
• pp.590-594
• /
• 2012

ZnO nanowires were fabricated by hydrothermal synthesis technique for field emission device application. Al-doped zinc oxide (AZO) thin films were prepared as seed layer of catalyst for the ZnO nanowire synthesis, for which conductivity of the seed layer was tried to be improved for enhancing the field emission property of the ZnO nanowire. The AZO seed layer revealed specific resistivity of $ 7.466{\times}10^{-4}[{\Omega}{\cdot}cm]$ and carrier mobility of 18.6[$cm^2$/Vs]. Additionally, upper tip of the prepared ZnO nanowires was treated by hydrochloric acid (HCl) to form a nanocone shape of ZnO nanowire, which was aimed for enhanced focusing of electric field on that and resultingly to improve field emission property of the ZnO nanowires. The ZnO nanowire with nanocone shape revealed decreased threshold electric field and increased current density than those of the simple ZnO nanowires.

• Journal of the Korean Geophysical Society
• /
• v.4 no.4
• /
• pp.251-256
• /
• 2001

Korean natura1 zeolite with fe1dspar and illite as impurities was purified by an air c1assification method. X-ray powder diffraction ana1yses showed that the air c1assification effectively separated zeolite and impurities, and reduce the amount of impurity of the natura1 zeolite. The zeolite with air c1assification was treated with 1N NaOH solutions at temperatures at 100, 150, 200 ℃ for 17hours. The obtained hydrotherma1 treatment of phase change to philli1site and ana1cime from mordenite and clinopti10lite.

• Journal of the Korean Ceramic Society
• /
• v.41 no.5
• /
• pp.370-374
• /
• 2004

Sr$_{l-x}$Ba$_{x}$Al$_2$O$_4$:Eu (x = 0, 0.1, 0.2, and 0.3 mol) phosphor was synthesized by the hydrothermal method and its properties of photoluminescence and long-afterglow were investigated. The mixtures of Sr(NO$_3$)$_2$, Al(NO$_3$)$_3$9$H_2O$, and Eu(NO$_3$)$_3$$.$6$H_2O$ salts dissolved in distilled water, after controlling their pH by NH$_4$OH solution, put into an Autoclave reactor with high temperature and pressure to react. Such synthesized SrAl$_2$O$_4$:Eu powders showed homogeneous and ultra-fine particles of sub-micron size. In order to have the photoluminescence characteristic, powders were heat treated at 1100 -140$0^{\circ}C$ for 2 h in Ar/H$_2$ reduction atmosphere. Photoluminescence spectra showed a excitation along the wide wavelength of 250 ∼ 450 nm, and broaden emission with maxima peak at 520 nm. Also, it showed a good long afterglow with decaying over 1000 sec after excitation illumination for 10 min. In addition, the microstructure and crystal structure of SrAl$_2$O$_4$:Eu powders were investigated by an SEM and XRD, respectively.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.32 no.5
• /
• pp.537-541
• /
• 1999

Fish heads of the main by-product is fishery processing were treated to extract nutrients by heating the fish heads with 1.5 or 3.0 times added water during 9, 12 or 15 hours. The yield, chemical compositions and physical properties of the hydrothermal extracts were studied. The yield was increased with the amount of water added and the extracting hours. The extract contained about $80\%$ protein in solid basis, but has no lipid. In essential amino acid, glutamic acid was most abundant and Iysine was abundant. In free amino acid, $\delta$-hydroxylysine and L-histidine in Cypyrinus carpio linnaeus had 5 times more than those in Onchorhynchus keta, The solution of the extracts was known as Newtonian fluid and the color of the extracts showed lower whiteness, higher redness and higher yellowness.