• Journal of the Korean Institute of Gas
• /
• v.27 no.2
• /
• pp.95-103
• /
• 2023

In this paper, in order to evaluate the deformation characteristics of the hydrogen gas storage vessel(Type 1) when considering gas pressure, the VMS generated in the hydrogen gas storage vessel according to the notch shape of ISO 18119 was interpreted as a FEM(Finite Element Method). According to the analysis results, the maximum VMS generated in the longitudinal notch was higher than the transverse notch. In addition, the stress of the storage vessel was analyzed by the stress ratio, which is the yield strength ratio of the material to the VMS generated. According to the analysis results, in the case of a storage vessel with a notch formed in the longitudinal direction, the inside and outside of the storage vessel increased to 0.85 and 0.50 at a gas pressure of 50 MPa, respectively, but were analyzed to be lower than 1.

• Journal of Hydrogen and New Energy
• /
• v.16 no.3
• /
• pp.262-268
• /
• 2005

[ $Zn(BH_4)_2$ ](8.4 wt% theoretical hydrogen storage capacity powders have been successfully synthesized by mechanochemical reaction from mixtures of $ZnCl_2$ and $NaBH_4$ powders in a 1:2 molar ratio in different times. $$ZnCl_2+2NaBH_4{\rightarrow}Zn(BH_4)_2+2NaCl$$ (1) $Zn(BH_4)_2$ powders were characterized by X-ray diffractometry(XRD), and Furier Transform Infrared spectrometry(FT-IR). The thermal stabilities of $Zn(BH_4)_2$ powders were studied by Differential scanning calorimetry(DSC), Thermogravimetry analysis(TGA), and Mass spectrometry(MS). $Zn(BH_4)_2$ can be tested for hydrogen evolution without further purification. The reaction to yield hydrogen is irreversible, the other products being compounds of Zn, and borane. $Zn(BH_4)_2$ thermally decomposes to release borane and hydrogen gas between about 85 and 150$^{\circ}C$.

• Journal of Hydrogen and New Energy
• /
• v.30 no.5
• /
• pp.385-394
• /
• 2019

The analysis of temperature behavior of a hydrogen tank during refueling is of significance to clarify the safety of the compressed hydrogen storage in vehicles since the temperature at a tank rises with inflow of hydrogen. A mass balance and an energy balance were combined to obtain analytical model for temperature change during the hydrogen refueling. The equation was coupled to Peng-Robinson-Gasem (PRG) equation of state (EOS) for hydrogen. The PRG EOS was adopted after comparison with other four different cubic EOSs. A parameter of the model was determined to fit data from experiments of various inlet flow rates and temperatures. The temperature and pressure change with refueling time were obtained by the developed model. The calculation results revealed that the extent of precooling was more effective than the flow rate control.

• Journal of the Korean Society of Safety
• /
• v.34 no.5
• /
• pp.7-14
• /
• 2019

The type III vessel, which is used to store high-pressure hydrogen gas, is made by wrapping the vessel's liner with carbon fiber composite materials for strength performance and lightening. The liner seals the internal gas and the composite resists the internal pressure. The properties of the fiber composite material depends on the angle and thickness of the fiber. Thus, engineers should consider these various design variables. However, it significantly increases the design cost due to the trial and error under designing based on experience or experiments. And, for aluminum liners, fatigue loads due to using and charging could give a huge impact on the performance of the structure. However, fatigue failure does not necessarily occur in the position under the highest load in use. Therefore, for hydrogen storage vessel, fatigue evaluation according to design patterns is essential because stress distribution varies depend on composite layer patterns. This study performed an optimization analysis and evaluated a high-pressure hydrogen storage vessel to minimize these trial and error and improve the reliability of the structure, while simultaneously conducting fatigue assessment of all patterns derived from the optimization analysis process. The results of this study are thought to be useful in the strength improvement and life design of composite reinforced high-pressure storage vessels.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.2
• /
• pp.95-99
• /
• 2006

Electrochemical properties were studied for a single particle of active material of hydrogen storage alloy $(MmNi_{3.55}Co_{0.75}Mn_{0.4}Al_{0.3})$ and nickel hydroxides $(NiOH)_2$ for the secondary Nickel Metal Hydride (Ni-MH) batteries using the microelectrode, which was manipulated to make electrical contact with an active material particle for cyclic voltammograms (CV) and potential-step experiments. As a result of CV test, it was found that three kinds of hydrogen oxidation peaks at -0.9, -0.75 and -0.65 V and hydrogen evolution peak at -0.98 V for hydrogen storage alloy were separately observed and two kinds of peaks of proton oxidation/reduction at 0.45 and 0.32 V and oxygen evolution reaction (OER) at 0.6 V for nickel hydroxides were also more clearly observed. Furthermore hydrogen diffusion coefficient within a single particle was also found to vary the order between $10^{-9}\;and\;10^{-10}cm^2/s$ over the course of hydrogenation and dehydrogenation process for potential-step experiments.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2001.05a
• /
• pp.389-389
• /
• 2001

• Journal of Hydrogen and New Energy
• /
• v.19 no.5
• /
• pp.394-402
• /
• 2008

The Effects of Cu or Ni additives co-added with Ce/Zr mixed oxides to Fe-based oxide mediums were investigated for the purpose of the replacement of Rh, a precious metal additive, in terms of hydrogen storage(reduction by hydrogen) and release(water splitting). From the results of temperature programmed reduction(TPR), initial reduction rate of iron oxide in the mediums was greatly increased with the addition of Cu, similar to that of Rh. For isothermal redox reaction of 10 cycles, the total amounts of hydrogen evolved in water splitting steps for the mediums added with Cu or Ni were highly maintained at ca. 7 mmol/g-material, even though the oxidation rates were slightly lower than that for the medium added with Rh. This result suggests that the replacement of Rh to Cu or Ni is possible as a co-additive for Fe-based oxide mediums.

• Korean Journal of Metals and Materials
• /
• v.50 no.12
• /
• pp.949-953
• /
• 2012

$MgH_2$ was employed as a starting material instead of Mg in this work. A sample with a composition of 94 wt% $MgH_2-6$ wt% Ni (called $MgH_2-6Ni$) was prepared by reactive mechanical grinding. The hydriding and dehydriding properties were then examined. An $MgH_2-Ni$ hydrogen storage alloy that does not require an activation process was developed. The alloy was prepared in a planetary ball mill by grinding for 4 h at a ball disc revolution speed of 250 rpm under a hydrogen pressure of about 12 bar. The sample absorbed 3.74 wt% H for 5 min, 4.07 wt% H for 10 min, and 4.41 wt% H for 60 min at 573 K under 12 bar $H_2$, and desorbed 0.93 wt% H for 10 min, 1.99 wt% H for 30 min, and 3.16 wt% H for 60 min at 573 K under 1.0 bar $H_2$. $MgH_2-6Ni$ after reactive mechanical grinding contained ${\beta}-MgH_2$ (a room temperature form of $MgH_2$), Ni, ${\gamma}-MgH_2$ (a high pressure form of $MgH_2$), and a very small amount of MgO. Reactive mechanical grinding of Mg with Ni is considered to facilitate nucleation, and to reduce the particle size of Mg. $Mg_2Ni$ formed during reactive mechanical grinding also increases the hydriding and dehydriding rates of the sample.

• Journal of Hydrogen and New Energy
• /
• v.17 no.3
• /
• pp.317-323
• /
• 2006

Electric conductive material should be homogeneously mixed with sulfur in sulfur electrode fabrication of lithium/sulfur battery, because sulfur is electric insulator. In this paper electrochemical properties of Li/S battery was studied with various compositions of sulfur electrodes. When content of sulfur changed from 40 wt.% to 80 wt.%, the 60 wt.% sulfur electrode showed the maximum capacity of 1489 mAh/g-sulfur. Electrochemical properties of Li/S battery using 60 wt.% sulfur was also investigated with various carbon contents. The discharge capacity changed as a function of carbon contents. The optimum composition was 25 wt.% carbon for 60 wt.% sulfur electrode.

• Journal of the Korean Institute of Gas
• /
• v.26 no.3
• /
• pp.38-44
• /
• 2022

As the supply of hydrogen charging stations for hydrogen supply accelerates due to the hydrogen economy revitalization policy, the risk of accidents is also increasing. Since most hydrogen explosion accidents lead to major accidents, it is very important to secure safety when using hydrogen energy. In order to utilize hydrogen energy, it is essential to secure the safety of hydrogen storage containers used for production, storage, and transportation of liquid hydrogen. In this paper, in order to evaluate the structural safety of a hydrogen-filled pressure vessel, the behavioral characteristics of gas pressure were analyzed by finite element analysis. SA-372 Grade J / Class 70 was used for the material of the pressure vessel, and a hexahedral mesh was applied in the analysis model considering only the 1/4 shape because the pressure vessel is axisymmetric. A finite element analysis was performed at the maximum pressure using a hydrogen gas pressure vessel, and the von Mises stress, deformation, and strain energy density of the vessel were observed.