• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.7
• /
• pp.21-29
• /
• 2004

Hot carrier degradation characteristics of Nano-scale CMOSFETs with dual gate oxide have been analyzed in depth. It is shown that, PMOSFET lifetime dominate the device lifetime than NMOSFET In Nano-scale CMOSFETs, that is, PMOSFET lifetime under CHC (Channel Hot Carrier) stress is much lower than NMOSFET lifetime under DAHC (Dram Avalanche Hot Carrier) stress. (In case of thin MOSFET, CHC stress showed severe degradation than DAHC for PMOSFET and DAHC than CHC for NMOSFET as well known.) Therefore, the interface trap generation due to enhanced hot hole injection will become a dominant degradation factor in upcoming Nano-scale CMOSFET technology. In case of PMOSFETs, CHC shows enhanced degradation than DAHC regardless of thin and thick PMOSFETs. However, what is important is that hot hole injection rather than hot electron injection play a important role in PMOSFET degradation i.e. threshold voltage increases and saturation drain current decreases due to the hot carrier stresses for both thin and thick PMOSFET. In case of thick MOSFET, the degradation by hot carrier is confirmed using charge pumping current method. Therefore, suppression of PMOSFET hot carrier degradation or hot hole injection is highly necessary to enhance overall device lifetime or circuit lifetime in Nano-scale CMOSFET technology

• Journal of Agricultural Extension & Community Development
• /
• v.18 no.2
• /
• pp.281-313
• /
• 2011

67.82% of domestic hot springs are in rural areas. (Ministry of Public Administration and Security statistics, 2010) Most of hot spring's facilities are aging and inability to accommodate the current changes of leisure patterns. So, a decrease of the number of visitor to the hot spring resulted in economic decline of rural areas. Hot spring has been studied, but Architecture of Hot Springs has never been interested in and research. Therefore, Nation architecture of Hot spring and foreign architecture was compared and analyzed. Then, Architectural characteristics of Hot spring in rural areas was identify. The architecture of Hot spring type of foreign and images are routinely burned, the organic form and old-fashioned adrift. However, our country found in Hot spring architecturally and daily life had any features. Thus, the country's hot springs spa area for construction of the architecture design should be characterized. And, through institutional guidelines and deliberations should be provided in the right direction.

• Design & Manufacturing
• /
• v.6 no.1
• /
• pp.39-44
• /
• 2012

Hot tool steel, in general, has not been used as a material in hot forging. However such a hot tool steel is recently applied to forging materials by recent forging technology. DH32 is known as a kind of hot tool steels, which is developed for characteristics of excellent strength and toughness in high temperature. Feasibility of DH32 to hot forging material has been researched to develop the hot forging technology of a plunger used for a large-sized marine fuel pump. Hot compression experimental works were performed to investigate the hot strain characteristic of DH32 and with the experimental results FE simulations were also conducted for the design of forging processes and preform. It is found out through the hot compression experimental works that DH32 has a hot brittleness at more than $1150^{\circ}C$.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.10a
• /
• pp.115-118
• /
• 1997

Recently, hot rolling oil lubrication technology is required to face with the new environments such as the rapid introduction of high wear resistent high speed steel roll the development of continuous hot rolling technology. In the hot strip mill, according to rolling and quality required conditions are constrict, Roll material of hot rolling finishing stand is changing Hi-Cr Roll to High Speed Steel [HSS] Roll. The problem of HSS Roll of roll force and strip scale defects are increasing in hot strip mill, So we have tested HSS Roll in hot rolling simulator as rolling condition, rolling speed, draft, hot oil concentration. To reduce roll force and prevent scale defects. We get some merit rolling force, rolling torque, roll wear reduction, roll and strip surface roughness and hot rolling critical oil concentration 0.4%. Finally we are going to investigate the effect of hot rolling oil of on rolling with HSS Roll.

• Journal of Magnetics
• /
• v.11 no.3
• /
• pp.103-107
• /
• 2006

In grain oriented electrical steel process, hot band annealing has thought to be essential for obtaining good magnetic properties. New hot rolling method of heavy reduction in early hot rolling stage was applied to obtain good magnetic properties in GO process without hot band annealing. Hot rolling was carried out by varyinghot rolling reduction distribution along hot rolling pass. The heavy hot rolling reduction in rear stand improves the magnetic flux density in the case of no hot band annealing. The hot band specimens of the heavy reduction in front stand shows the elongated hot deformed microstructures in the center layer and strong {001}<110> texture.On the contrary, the heavily reduced specimens in rear stand shows the recrystallization in the center layer of hot band and strong {111}<112> and {110}<001> textures.

• 전자공학회논문지 IE
• /
• v.45 no.4
• /
• pp.7-10
• /
• 2008

In this work investigates hot carrier stress on the RF power of SOI MOSFET using load-pull measurement. We found that the RF power characteristics are affected by the hot carrier stress, and the DC performance of SOI MOSFET is clearly degraded after hot carrier stress at constant voltage measurement. And these experimental observations can be explained by the change of DC performance degradation coefficient under hot carrier stress.

• Journal of the Korean Society of Safety
• /
• v.27 no.2
• /
• pp.7-12
• /
• 2012

This paper describes electrical fire on electric pad caused by defect of hot wires. We analyzed two type electric pad using by carbon type hot wire and magnetic shielded type hot wire. First, a carbon type hot wires electric pad is virtually impossible to connect hot wire as a method of electrical welding or soldering. In order to connect between hot wires, that has to splice carbon type material connector. If junction of hot wires was occurrence of poor connection on electric pad, it increase contact resistance on this junction point. With increasing contact resistance, junction of hot wires on electric pad generates local heating and finally leads to electrical fire. An electric pad using by a magnetic shielded type hot wire happened local heating on signal wire for sensing temperature-rise caused by applying current for magnetic shielded. With increasing local heating of signal wire, insulated coating of hot wire was melted. Finally the magnetic shielded type hot wire electric pad lead to electrical fire with breakdown between signal wire and hot wire. In this paper, we analyzed shape of damage in hot wire caused by electrical local heating and investigated fire cause on electric pad due to defect of hot wires.

• Journal of The Korean Society of Integrative Medicine
• /
• v.11 no.4
• /
• pp.189-198
• /
• 2023

Purpose: This study aims to investigate the preferences of hot spring users regarding the utilization of Asan's hot springs after the COVID-19 pandemic. Methods: A survey was conducted on 340 hot spring users visiting hot spring resorts in the Onyang, Dogo, and Asan hot spring districts. The survey was conducted twice from November 5th to November 7th, 2021, and from May 25th to 26th, 2022. The survey included general questions, such as the frequency of hot spring usage, the purpose of visits, and the intention for future visits. Specific questions were related to Asan hot springs, focusing on the reasons for choosing Asan, its perceived advantages, and improvement suggestions. Results: The survey revealed that the average number of visits to hot springs was less than five in the past five years, and the main reason for visiting was to recover from fatigue. A percentage of respondents said they would use hot springs more often when the COVID-19 pandemic ends. When asked about their reasons for visiting Asan hot springs, responses varied by age. However, across all groups, the majority considered "good water" as an advantage of Asan hot springs, while improvements to "hot spring facilities" was the highest response among all age groups. Thus, despite the decline in the number of customers due to COVID-19, the overall perception of hot springs remains positive. This suggests a promising future for the hot spring industry, with the potential for a return to pre-pandemic usage levels. Conclusion: These results provide valuable foundational data for informing policy development aimed at revitalizing the hot spring industry in the post-COVID-19 era.

• Journal of the East Asian Society of Dietary Life
• /
• v.25 no.5
• /
• pp.842-849
• /
• 2015

The purpose of this study was to determine the optimal mixing ratio of hot-air dried loquat leaf powder and optimum conditions for making Jeolpyun containing hot-air dried loquat leaf powder (LLP). Samples of Jeolpyun were prepared with different contents of hot-air dried LLP (0%, 3%, 6%, 9%, 12%) followed by analysis of chemical properties, moisture contents, color, mechanical quality characteristics, amylograph, and sensory tests. Chemical analysis showed that hot-air dried LLP consisted of 11.41% water, 8.34% crude protein, 1.90% crude fat, 7.74% crude ash, and 16.95% crude fiber, with $^{\circ}Brix$ of 2.07, and pH of 5.78. Moisture contents of samples ranged from 52.22 to 50.06%. L-value decreased with addition of hot-air dried LLP, whereas a-value increased with increasing amount of hot-air dried LLP, and no significant differences were observed regarding b-value. In the mechanical evaluation of physical properties, hardness deceased with increasing amount of hot-air dried LLP. The starting temperature amylograph of Jeolpyun was higher in samples with hot-air dried LLP than those without hot-air dried LLP. Set back was slower with increasing amount of hot-air dried LLP, an increasing amount of hot-air dried LLP made set back of Jeolpyun slower. In the sensory test, Jeolpyun with 6% hot-air dried LLP was the most preferred with less bitterness and proper softness, moisture and chewiness. Therefore, addition of 6% hot-air dried LLP to Jeolpyun made with rice flour showed the best overall preference. Based on the results of this experiment, samples with hot-air dried LLP showed slower hardening than those without hot-air dried LLP in textural changes during storage, and Jeolpyun with 6% hot-air dried LLP is expected to increase quality and preference of Jeolpyun.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.375-378
• /
• 2009

Hot press forming is a new forming process which also names as hot stamping. It can greatly enhance the formability of forming parts. This paper researches the formability of boron steel sheet in hot bending process which is a kind of hot press forming. In the text, the influence of hot press forming processing parameters, such as the heating temperature, blank holding force, punch speed and punch and die radius, on the mechanics properties and microstructure of the hot bending parts was analyzed by tension test and the metallographic observation on the parts with various processing parameters. The relationship between blank holding force and punch load was also presented.