• Journal of Electrical Engineering and information Science
• /
• v.1 no.2
• /
• pp.96-100
• /
• 1996

This paper describes a concrete method for computing characteristic impedances and effective dielectric constants of the microstrip coupled lines without and with a dielectric overlay. The frequency-independent spectral domain method is used for the analysis of these lines. This method is a powerful, accurate, and numerically efficient approach for planar transmission line structure. For designing the optimal directional coupler, the velocities of even and odd mode must be equal but velocities of these two modes are different in the conventional coupled line which is inhomogeneous. The results show that these two velocities can be almost same according to variations of structural and material parameters in terms of the overlay(superstrate).

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.7-13
• /
• 2008

To obtain a shear-wave velocity profile in geotechnical practice, various seismic investigation methods which have their own strength and weakness are being frequently used. Generally, geotechnical site have lateral variation of the properties, so it is needed to determine 2-dimensional shear wave velocity imaging of the site. In this study, harmonic wavelet analysis of wave (HWAW) method is applied to determination of 2-D $V_s$ imaging. HWAW method which is based on time-frequency analysis using harmonic wavelet transform have been developed to determine phase and group velocities of waves. HWAW method uses the signal portion of the maximum local signal/noise ratio to evaluate the phase velocity to minimize the effects of noise. HWAW method determine detailed local $V_s$ profile because one experimental setup which consists of one pair of receivers with spacing of 1~3m is used to determine the dispersion curve of the whole depth. So, 2-D Vs imaging with relatively high resolution can be determined through a series of HWAW test. In order to estimate the applicability of HWAW method, field tests were performed in 4 sites. Through field applications and comparison with other test results, the good accuracy and applicability of the proposed method were verified.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.32 no.1
• /
• pp.38-46
• /
• 2016

Purpose: study for discriminating method of origin side vibration from non-symptomatic clicking group. Materials and Methods: 60 joints vibrations of 30 subjects in non-symptomatic clicking group was recorded via subject's awareness, examiner's palpation and JVA analysis. Origin side vibration was discriminated with consideration for frequency spectrum, time delay and phase shift of waveforms, analysis of numeric values. Results: There were all unilateral vibrations with JVA analysis and number of origin vibrations were 42. 11 pairs of vibrations showed time delay and phase shift and transferred side vibrations showed smaller values of total integral and bigger values of > 300 / < 300 ratio than origin side vibrations except one pair of vibrations. Also as the ipsi-lateral joint vibrations with smaller values of total integral showed bigger values of > 300 / < 300 ratio than the contra-lateral joint vibrations and there all ipsi-lateral vibrations were showed small values of total integral below 10 and hard to detect time delay and phase shift. So the features were used in discrimination of origin side vibrations. Conclusion: There should be all-around considerations for discrimination of origin side vibrations that is frequency spectrum, phase shift and time delay and analysis of numeric values.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.11
• /
• pp.73-81
• /
• 2016

In general, infrared images have less sharpness and image details than visible images. So, the prior image upscaling methods are not effective in the infrared images. In order to solve this problem, this paper proposes an algorithm which initially up-scales an input infrared (IR) image by using adaptive dynamic range encoding (ADRC)-based super-resolution (SR) method, and then fuses the result with the corresponding visible images. The proposed algorithm consists of a up-scaling phase and a fusion phase. First, an input IR image is up-scaled by the proposed ADRC-based SR algorithm. In the dictionary learning stage of this up-scaling phase, so-called 'pre-emphasis' processing is applied to training-purpose high-resolution images, hence better sharpness is achieved. In the following fusion phase, high-frequency information is extracted from the visible image corresponding to the IR image, and it is adaptively weighted according to the complexity of the IR image. Finally, a up-scaled IR image is obtained by adding the processed high-frequency information to the up-scaled IR image. The experimental results show than the proposed algorithm provides better results than the state-of-the-art SR, i.e., anchored neighborhood regression (A+) algorithm. For example, in terms of just noticeable blur (JNB), the proposed algorithm shows higher value by 0.2184 than the A+. Also, the proposed algorithm outperforms the previous works even in terms of subjective visual quality.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.2 no.4
• /
• pp.42-51
• /
• 2003

In this paper, we are going to analyze on relation of an output spectrum along phase distortion of power amplifier in wireless LAN system, and then considered an ACPR characteristic of power amplifier and consideration of an OFDM method for this. Also, we did implementation for OFDM modulation and transmission section of an IEEE 802.11a standard to have transmission speed of the maximum 54Mbps in order to know an OFDM modulation method and relation of non-linear characteristic of power amplifier. The non-linear characteristic of power amplifier did modeling with AM-to-AM and AM-to-PM, and we analyzed an output spectrum characteristic along phase distortion composed input signal supply for power amplifier. When output spectrum analysis results phase distortion increased, and an AM-to-PM characteristic of power amplifier in 5 degrees, the output spectrum was satisfied with a demand spectrum in P1 dB, but 10-20 degrees were able to confirm what cannot be satisfied with a demand spectrum in phase distortion. Also, an output spectrum of power amplifier by frequency re-growth generated by a non-linear characteristic of power amplifier did not satisfied in P1dE. therefore, a back-off value was requested according to an AM-to-PM distortion degree, and smaller back-off value were able to know what demand became in case of modulation section that used OFDM.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.1
• /
• pp.37-49
• /
• 2007

To detect islanding mode when the grid is being tripped is a major safety issue in utility interactive PV(UIPV) system. Widely used techniques among various active methods to detect islanding mode are Reactive power variation (RPV)method and Active frequency drift(AFD) method. In this paper, analytical design method is suggested for AFD and RPV method under IEEE recommended islanding test condition. And in order to show the validity of proposed method, EMTP based simulation was done for UIPV system with RPV method and AFD method. Results shows proposed method is very useful.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.4
• /
• pp.71-79
• /
• 1992

In general, the accelerogram of earthquake ground motion or the accelerogram obtained from dynamic tests contain various errors. In these errors of the accelerograms, there are instrumental errors(magnitude and phase distortion) due to the response characteristics of accelerometer and the digitizing error concentrated in low and high frequency components and random errors. Then, these errors may be detrimental to the results of data processing and dynamic analysis. An efficient method which can correct the errors of the accelerogram is proposed in this study. The correction of errors can be accomplished through four steps as followes ; 1) using an interpolation method a data form appropriate to the error correction is prepared, 2) low and high frequency errors of the accelerogram are removed by band-pass filter between prescribed frequency limits, 3) instrumental errors are corrected using dynamic equilibrium equation of the accelerometer, 4) velocity and displacement are obtained by integrating corrected accelerogram. Presently, infinite impulse response(IIR) filter and finite impulse response (FIR) filter are generally used as band-pass filter. In the proposed error correction procedure, the deficiencies of FIR filter and IIR filter are reduced and, using the properties of the differentiation and the integration of Fourier transform, the accuracy of instrument correction and integration is improved.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.3
• /
• pp.83-89
• /
• 2000

In hydraulic control system turbine and gear motor type flowmeters are widely used to measure the flow rate under steady flow conditions. With the recent growth of interest in the measurement of instantaneous values of unsteady flow rate the test of the transient response of these flowmeters are in some significance. however an unsteady flow rate mea-surment and its calibration method with a fast response and a high accuracy have not beendeveloped. In this research particularly the dynamic characteristics of turbine and gear motor type flowmeters are investigated experimentally and simple mathematical models are proposed. The measured flow rate waveforms are compared with those by remote instan-taneous flow rate measurement method(RIFM) which has been developed by author and used for calibration As the result of frequency response test gain and phase between the measured flow rate waveforms by turbine type flowmeter and those estimated by RIFM are in good agreement up to 70Hz For the gear motor type flowmeter th simulated results by a math-ematical model proposed here agree well with the experiment nearly up to 100Hz. Also it if sound that the pressure drop across the flowmeter is increased in proportion to the frequency of the flow rate variation in a high frequency region of more than 100Hz. It can be explained that the dealy of gear motor type flowmeter in high frequency regionis mainly attributed to a first order delay consisting of the inertia of gears and internal leakage of the gear motor.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.9
• /
• pp.64-72
• /
• 1998

In this paper, the design of a current integrator for low-voltage, low-power, and high frequency applications using complementary high swing cascode current-mirror is presented. The proposed integrator decreases output current errors due to non-zero input resistance and non-infinite output resistance of the simple current integrator. As a design example, the 3rd order Butterworth lowpass filter is designed by a leapfrog method. Also, we apply the predistortion design method to reduce the magnitude distortion which occurs at a cutoff frequency by the undesirable phase shift of a lossless current integrator. The designed current-mode filter is simulated and examined by SPICE using 0.8$\mu\textrm{m}$ CMOS n-well process parameters. The simulation results show 20MHz cutoff frequency and 615㎼ power dissipation with a 2V power supply. And the cutoff frequency of the filters can be easily changed by the DC bias current.

• Nuclear Engineering and Technology
• /
• v.55 no.1
• /
• pp.109-118
• /
• 2023

In this paper, the evaluation method of fluidelastic instability (FEI) of newly designed steam generator tubing in pressurized water reactor (PWR) nuclear power plants is discussed. To obtain the parameters for prediction of the critical velocity of FEI for steam generator tubes, experimental research is carried out, and the design parameters are determined. Using CFD numerical simulation, the tube array scale of the model experiment is determined, and the experimental device is designed. In this paper, 7 groups of experiments with void fractions of 0% (water), 10%, 20%, 50%, 75%, 85% and 95% were carried out. The critical damping ration, fundamental frequency and critical velocity of FEI of tubes in flowing water were measured. Through calculation, the total mass and instability constant of the immersed tube are obtained. The critical damping ration measured in the experiment mainly included two-phase damping and viscous damping, which changed with the change in void fraction from 1.56% to 4.34%. This value can be used in the steam generator design described in this paper and is conservative. By introducing the multiplier of frequency and square root of total mass per unit length, it is found that the difference between the experimental results and the calculated results is less than 1%, which proves the rationality and feasibility of the calculation method of frequency and total mass per unit length in engineering design. Through calculation, the instability constant is greater than 4 when the void fraction is less than 75%, less than 4 when the void fraction exceeds 75% and only 3.04 when the void fraction is 95%.