• Structural Engineering and Mechanics
• /
• v.75 no.4
• /
• pp.435-444
• /
• 2020

Ultrasonic guided wave testing is a very promising non-destructive testing method for rails, which is of great significance for ensuring the safe operation of railways. On the basis of the semi-analytical finite element (SAFE) method, a analytical model of 59R2 grooved rail was proposed, which is commonly used in the ballastless track of modern tram. The dispersion curves of ultrasonic guided waves in free rail and supported rail were obtained. Sensitivity analysis was then undertaken to evaluate the effect of rail elastic modulus on the phase velocity and group velocity dispersion curves of ultrasonic guided waves. The optimal guided wave mode, optimal excitation point and excitation direction suitable for detecting rail integrity were identified by analyzing the frequency, number of modes, and mode shapes. A sinusoidal signal modulated by a Hanning window with a center frequency of 25 kHz was used as the excitation source, and the propagation characteristics of high-frequency ultrasonic guided waves in the rail were obtained. The results show that the rail pad has a relatively little influence on the dispersion curves of ultrasonic guided waves in the high frequency band, and has a relatively large influence on the dispersion curves of ultrasonic guided waves in the low frequency band below 4 kHz. The rail elastic modulus has significant influence on the phase velocity in the high frequency band, while the group velocity is greatly affected by the rail elastic modulus in the low frequency band.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.1
• /
• pp.1-8
• /
• 2017

The optimal gain design method of a three-phase boost converter is proposed in this study. The control system has a two-loop configuration, in which each controller is coupled closely; thus, the optimal design is difficult to achieve using conventional gain-tuning method. The proposed method is adopted to the MATLAB SISO TOOL software and is based on the controller requirements, which are phase margin and cut-off frequency of the open-loop system. The optimal proportional -integral gains can be designed easily using the proposed interactive method of the SISO TOOL. The performance of the proposed system is verified through simulation and experiments.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.3
• /
• pp.81-86
• /
• 2010

Since CORDIC (COordinate Rotation DIgital Computer) is able to carry out the phase operation, such as vector to phase conversion or rotation of vectors, with adders and shifters, it is well suited for the design of the frequency synchronization unit in OFDM receivers. It is not easy, however, to fully utilize the CORDIC in the OFDM demodulator because of the non-linear characteristics of the direction sequence (DS), which is the representation of the phase in CORDIC. In this paper a new representation method is proposed to linearize the direction sequence approximately. The maximum phase error of the linearized binary direction sequence (LBDS) is also discussed. For the purpose of designing the hardware, the architectures for the binary DS (BDS) to LBDS converter and the LBDS to BDS inverse converter are illustrated. Adopting LBDS, the overall frequency synchronization hardware for OFDM receivers can be implemented fully utilizing CORDIC and general arithmetic operators, such as adders and multipliers, for the phase estimation, loop filtering of the frequency offset, derotation for the frequency offset correction. An example of the design of 22 bit LBDS for the T-DMB demodulator is also presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.499-506
• /
• 2012

In this paper, we analyze the effects of phase noise and frequency offset that cause performance degradation. Basically, we like to propose reduced PNFS(Phase Noise and Frequency offset Suppression) algorithm. The OFDM system is seriously affected by ICI component such as phase noise, frequency offset and Doppler effects. Especially, complicated processing algorithm with high complexity was required it in order to compensate those ICI components. So, we propose PNFS algorithm that can decrease complexity and compensate ICI components. We propose a method decreased complexity by approximation of parameters that affect slightly performance change and compare the quantity of conventional and revised PNFS algorithm. Also, simulation shows that BER performance of revised PNFS algorithm can be improved slightly.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.2
• /
• pp.101-105
• /
• 2018

Shortage of electric power occurs frequently along with increased electric power demand. ESS is a precaution to solve this issue. Household ESS has a capacity of approximately 3 kW/7 kWh. Household ESS batteries are typically designed with nominal voltages between 40 and 50 V. To connect household ESS with a 220 V AC system, low battery voltages in power conditioning system (PCS) should be boosted. To boost low battery voltage and match it with AC grid voltage, the use of a transformer for a commercial frequency can be considered. To attenuate switching harmonics of the household single-phase ESS-PCS, LC filter can be installed in two positions: on the primary side or on the secondary side of a transformer. A method has been used generally in single-phase inverters for the ESS-PCS. In another method, however, the output efficiency of the ESS-PCS may be decreased. Parasitic components of the transformer can affect voltage losses, when the square wave with the switching frequency in the ESS-PCS is passed through the transformer windings. In this work, the characteristics of the transformer according to the position of an LC filter are investigated for household single-phase ESS-PCS.

• Journal of the Institute of Convergence Signal Processing
• /
• v.15 no.3
• /
• pp.91-96
• /
• 2014

For Sound source direction and separation method, Frequency Domain Binaural Model(FDBM) shows low computational cost and high performance for sound source separation. This method performs sound source orientation and separation by obtaining the Interaural Phase Difference(IPD) and Interaural Level Difference(ILD) in frequency domain. But the problem of reflection occurs in practical environment. To reduce this reflection, a method to simulate the sound localization of a direct sound, to detect the initial arriving sound, to check the direction of the sound, and to separate the sound is presented. Simulation results show that the direction is estimated to lie close within 10% from the sound source and, in the presence of the reflection, the level of the separation of the sound source is improved by higher Coherence and PESQ(Perceptual Evaluation of Speech Quality) and by lower directional damping than those of the existing FDBM. In case of no reflection, the degree of separation was low.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.7
• /
• pp.29-36
• /
• 2013

In this paper, a new DC offset elimination filter is proposed for an accurate phasor extraction of fundamental frequency component. The proposed method can eliminate a DC offset component which is decayed exponentially. The proposed method uses only one cycle of data for phasor extraction computation, which does not need to preset the time constant of the DC offset component. Also, the other advantages of the proposed method is that gain compensation or phase compensation is not required after filtering. Simulations using ATP were performed to evaluate the performance of the proposed filter method, and the results were compared to the ones obtained by conventional methods.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.4
• /
• pp.1558-1565
• /
• 2018

Three-phase current is reconstructed from the dc-link current in an AC machine drive with a single current sensor. Switching pattern modification methods, in which the magnitude of the effective voltage vector is secured over its minimum, are investigated to accurately reconstruct the three-phase current. However, the existing methods that modify the switching pattern cause voltage and current distortions that degrade sensorless performance. This paper proposes a variable-magnitude voltage signal injection method based on a high frequency voltage signal injection. The proposed method generates a voltage reference vector that ensures the minimum magnitude of the effective voltage vector by varying the magnitude of the injection signal. This method can realize high quality current reconstruction without switching pattern modification. The proposed method is verified by experiments in a 600W Interior permanent magnet synchronous machine (IPMSM) drive system.

• Sleep Medicine and Psychophysiology
• /
• v.19 no.1
• /
• pp.11-17
• /
• 2012

Objective: Among various methods developed to quantitatively explore electroencephalograms (EEG), we focused on a wavelet method that was known to yield robust results under nonstationary conditions. The aim of this study was thus to introduce the wavelet method and demonstrate its potential use in clinical sleep studies. Method: This study involved artificial EEG specifically designed to validate the wavelet method. The method was performed to obtain time-dependent spectral power and phase angles of the signal. Synchrony of multichannel EEG was analyzed by an order parameter of the instantaneous phase. The standard methods, such as Fourier transformation and coherence, were also performed and compared with the wavelet method. The method was further validated with clinical EEG and ERP samples available as pilot studies at academic sleep centers. Result: The time-frequency plot and phase synchrony level obtained by the wavelet method clearly showed dynamic changes in the EEG waveforms artificially fabricated. When applied to clinical samples, the method successfully detected changes in spectral power across the sleep onset period and identified differences between the target and background ERP. Conclusion: Our results suggest that the wavelet method could be an alternative and/or complementary tool to the conventional Fourier method in quantifying and identifying EEG and ERP biomarkers robustly, especially when the signals were nonstationary in a short time scale (1-100 seconds).

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.1
• /
• pp.111-117
• /
• 2003

In the design of the split type free displacer Stilting cryocooler the motion of the displacer is very important to decide the cooling capacity, which depends upon the working gas pressure, the swept volume in the compression space and the expansion space, operating frequency, the phase shift between piston and displacer, etc. In this study, Stirling cryocooler actuated by the electric farce of the dual linear motor is designed and manufactured. Cool down characteristics of the cold end with laser displacement sensor in the expander of the Stilting cryocooler is evaluated. The charging pressure was 15kg$_{f}$/$\textrm{cm}^2$ and operating frequency was 50Hz. Input power and the lowest temperature were about 32W and 67K, respectively. And, displacement of the piston is measured by LVDTs (Linear Variable Differential Transformers), displacement of thedisplacer is measured by laser optic method, and phase shift between piston and displacer is discussed. As the peak-to-peak pressure of the compressor was increased, peak-to-peak displacement of the displacer was increased. The peak-to-peak displacement of the displacer increases in the range of 0 - 64.5Hz(resonant frequency of the displacer), but decreases steeply when the operating frequency is bigger than the resonant frequency. Finally when the phase shift between displacements of the Piston and displacer is 45。, operating frequency is optimum and is decided by resonant frequency of the expander, mass and cross section area of the displacer and constant by friction and flow resistance.e.